Items where Subject is "Materials Science"

Sridhar, Seetharaman and Sampson, Erica (2013) Recycling High-Residual Scrap in EAF – Fundamental Research Aimed at pushing the limits. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking , December 16-18, 2013, CSIR-NML Jamshedpur.

A

Abdlmanam, S and Elmaryami, A and Omar, Badrul (2011) Developing 1-D mm of axisymmetric transient quenched molybdenum steel AISI-SAE 4037H to determine lowest hardness point. Journal of Metallurgy and Materials Science, 53 (3). pp. 289-303.

Abhilash, and Meshram, Pratima (2019) Recovery of Rare Earth Elements from Metallurgical Wastes. In: Sustainable and Economic Waste Management-Resource Recovery Techniques. CRC Press, Australia, pp. 247-262. ISBN 9780367232559

Addanki Rao, S and Lahiri, A K and Banerjee, T (1961) Corrosion of Nickel in Steam Condensate Containing Air and Carbondioxide. NML Technical Journal, 3 (4). pp. 21-24.

Adeleke, A A and Kanna, M Barath and Kolawole, J Odusote and Malathi, M and Ajani, O Lasode and Paswan, Dayanand (2017) Influence of binder composition on briquetting of coal slacks. In: Influence of binder composition on briquetting of coal slacks, Dec 2017, IIT Kanpur.

Agarwal, P K (1994) Thermo-Chemical Surface Hardening Treatment of Steels. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Aggarwal, Nishant (2013) Effect of Phosphorus on Mild Steel - From A Structural Engineer’s View. In: Proceeding Of International Seminar on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Agrawal, A and Bagchi, D and Kumari, S and Kumar , Vinay and Pandey, B D (2008) Hydrogen reduction of bleed stream of an Indian copper industry to produce nickel powder. Materials Letters, 62 (17-18). pp. 2880-2882.

Agrawal, A and Kumar, Vinay and Pandey, B D and Sahu, K K (2006) A comprehensive review on the hydro metallurgical process for the production of nickel and copper powders by hydrogen reduction. Materials Research Bulletin, 41 (4). pp. 879-892.

Agrawal, A and Manoj, M K and Kumari, S and Bagchi, D and Kumar, Vinay and Pandey, B D (2008) Extractive separation of copper and nickel from copper bleed stream by solvent extraction route. Minerals Engineering, 21 (15). pp. 1126-1130.

Agrawal, A and Pal, C and Sahu, K K (2008) Extractive removal of chromium (VI) from industrial waste solution. Journal of Hazardous Materials, 159 (2-3). pp. 458-464.

Agrawal, A and Sahu, K K (2005) Detoxification of cadmium from industrial effluents using solid waste generated after sea nodule processing. In: Proceedings of the Sixth (2005) ISOPE Ocean Mining Symposium, 2005, ISOPE Ocean Mining Symposium.

Agrawal, A and Sahu, K K (2005) Influence of temperature on the exchange of alkaline earth and transition metals on iminodiacetate resin. Solvent Extraction and Ion Exchange, 23 (2). pp. 265-287.

Agrawal, A and Sahu, K K (2006) Kinetic and isotherm studies of cadmium adsorption on manganese nodule residue. Journal of Hazardous Materials, 137 (2). pp. 915-924.

Agrawal, A and Sahu, K K (2009) An overview of the recovery of acid from spent acidic solutions from steel and electroplating industries. Journal of Hazardous Materials, 171 (1-3). pp. 61-75.

Agrawal, A and Sahu, K K (2005) Potential utilisation of manganese nodule leach residue as a scavenger for cadmium from industrial effluents. Journal of Metallurgy and Materials Science, 47 (3). pp. 141-148.

Agrawal, A and Sahu, K K (2010) Problems, prospects and current trends of copper recycling in India: An overview. Resources, Conservation and Recycling, 54 (7). pp. 401-416.

Agrawal, A and Sahu, K K (2006) Separation and recovery of lead from a mixture of some heavy metals using Amberlite IRC 718 chelating resin. Journal of Hazardous Materials, 133 (1-3). pp. 299-303.

Agrawal, A and Sahu, K K (2009) Value Addition to Sulfate Waste Pickle Liquor of Steel Industry Using Hydrometallurgical Processes. Metallurgical and Materials Transactions B, 40 (6). pp. 877-885.

Agrawal, A and Sahu, K K and Pandey, B D (2004) Recent trends and current practices for secondary processing of zinc and lead. Part I: lead recovery from secondary sources. Waste Management & Research, 22 (4). pp. 240-247.

Agrawal, A and Sahu, K K and Pandey, B D (2004) Removal of zinc from aqueous solutions using sea nodule residue. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 237 (1-3). pp. 133-140.

Agrawal, A and Sahu, K K and Pandey, B D (2004) Separation and removal of cobalt and zinc from chloride solution by Indion BSR - A chelating resin. Separation Science and Technology, 39 (10). pp. 2373-2388.

Agrawal, A and Sahu, K K and Pandey, B D (2005) Systematic studies on adsorption of lead on sea nodule residues. Journal of Colloid and Interface Science, 281 (2). pp. 291-298.

Agrawal, A and Sahu, K K and Rawat, J P (2003) Kinetic studies on the exchange of bivalent metal ions on amberlite IRC-718-an iminodiacetate resin. Solvent Extraction and Ion Exchange, 21 (5). pp. 763-782.

Agrawal, A and Sekhar, K C and Pandey, L P (1994) Spectrophotometric determination of ce(iv) using o-phenylenediamine in steels. Bulletin of Materials Science, 17 (7). pp. 1467-1471.

Agrawal, J C and Davis Jr, W L (1962) Recent Advances in Blast-Furnace Technology. NML Technical Journal, 4 (4). pp. 23-30.

Ahmad, Khalil and Ali, Muhammad and Ibrahim , Ather and Baig, Waqas Mehmood (2014) Optimising the yield of silicon carbide synthesised from indigenous biomass husk using different catalysts. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 23-27.

Ahmed, Zanab and Kumari, Sarita and Goswami, N G and Sinha, Arvind and Bandyopadhyaya, Rajib (2016) A Report on the 6th Annual Conference of "National Academy of Sciences, India (NASI)" (September 24-25, 2014; Venue-CSIR-National Metallurgical Laboratory, Jamshedpur-831007). National Academy Science Letters - India, 39(2) (IF-0.369). pp. 133-134.

Ahuja, P L and Halder, B N and Bhatnagar, S S (1971) Structures of some 17% Cr(Mn, N) stainless steels. Journal of Materials Science, 6 (5). pp. 439-447.

Aich, S and Das, D and Al-Omari, I A and Alagarsamy, P and Ghosh Chowdhury, S and Chakraborty, M and Shield, J E and Sellmyer, D J (2009) Microstructures and magnetic properties of rapidly solidified Ni54Fe27-2xGa19+2x ferromagnetic Heusler alloys. Journal of Applied Physics, 105 (7). 07A943.

Aireddy, H and Mishra, S C (2011) Tribological behavior and mechanical properties of Bio-waste reinforced polymer matrix composites. Journal of Metallurgy and Materials Science, 53 (2). pp. 139-152.

Akhtar, M and Khajuria, A (2020) Effects of prior austenite grain size on impression creep and microstructure in simulated heat affected zones of boron modified P91 steels. Materials Chemistry and Physics, 249 (IF-3.408). p. 122847.

Akhtar, Mohammad Nishat and Khan, Muneer and Khan, Sher Afghan and Afzal, Asif and Subbiah, Ram and Ahmad, Sheikh Nazir and Husain, M M and Butt, Mohammad Mursaleen and Othman, Abdul Rahim and Bakar, Elmi Abu (2021) Determination of Non-Recrystallization Temperature for Niobium Microalloyed Steel. Materials, 14(10) . p. 2639.

AL-Jarrah, J A and Ghosh, P K and Ray, S (1998) Mixing & solidification Processing of AI-AI2o3 Composite. In: UNSPECIFIED.

Al-Samman, T and Li, X and Ghosh Chowdhury, S (2010) Orientation dependent slip and twinning during compression and tension of strongly textured magnesium AZ31 alloy. Materials Science and Engineering: A, 527 (15). pp. 3450-3463.

Alex, T C (2014) An insight into the changes in the thermal analysis curves of boehmite with mechanical activation. Journal of Thermal Analysis and Calorimetry, 117 (IF-2.206). pp. 163-171.

Alex, T C and Kailath, A J and Kumar, Rakesh (2020) Al-Monohydrate (Boehmite) to Al-Trihydrate(Bayerite/Gibbsite) Transformation During High-Energy Milling. Metallurgical and Materials Transactions B, 51 (IF-1.874). pp. 443-451.

Alex, T C and Kumar, Rakesh and Roy, S K and Mehrotra, S P (2014) Mechanically induced reactivity of gibbsite: Part 1. Planetary milling. Powder Technology, 264 (IF-2.269). pp. 105-113.

Alex, T C and Kumar, Rakesh and Roy, S K and Mehrotra, S P (2014) Mechanically induced reactivity of gibbsite: Part 2. Attrition milling. Powder Technology, 264 (IF-2.269). pp. 229-235.

Alex, T C and Kumar, Rakesh and Roy, S K and Mehrotra, S P (2008) Stirred bead mill grinding of gibbsite: Surface and morphological changes. Advanced Powder Technology, 19 (5). pp. 483-491.

Alex, T C and Kumar, Rakesh and Roy, S K and Mehrotra, S P (2014) Towards ambient pressure leaching of boehmite through mechanical activation. Hydrometallurgy, 144 (IF-2.224). pp. 99-106.

Alex, T C and Kumar, Rakesh and Upadhyay, A K and Mishra, T and Mahato, B and Mehrotra, S P (2007) Role of Mineralogy and Origin of Mechanically Activated (Indian) bauxite in Bayer Process. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Alex, T C and Sasikumar, C and Kailath, A J and Kumar, Rakesh and Roy, S K and Mehrotra, S P (2011) Analysis of Mechanically Induced Reactivity of Boehmite Using Kinetics of Boehmite to gamma-Al2O3 Transformation. Metallurgical and Materials Transactions B-Process Metallurgy and Materials Processing Science, 42 (3). pp. 592-603.

Alhozaimy, Abdulrahman and Hussain, Raja Rizwan and Al-Negheimish, Abdulaziz and Al-Zaid, Rajeh and Singh, D D N (2014) Effect of Simulated Concrete Pore Solution Chemistry, Chloride Ions, and Temperature on Passive Layer Formed on Steel Reinforcement. ACI Materials Journal, 111/4 (IF-1.123). pp. 411-421.

Ali, F and Scudino, S and Anwar, M S and Shahid, R N and Srivastava, V C and Uhlenwinkel, V and Stoica, M and Vaughan, G and Eckert, J (2014) Al-based metal matrix composites reinforced with Al-Cu-Fe quasicrystalline particles: Strengthening by interfacial reaction. Journal of Alloys and Compounds, 607 (IF-2.407). pp. 274-279.

Ali, Rashid and Akhtar, Muhammad Umair and Zahoor, Aqib and Ali, Fahad and Scudino, Sergio and Shahid, Rub Nawaz and Tariq, Naeem ul Haq and Srivastava, V C and Uhlenwinkel, V and Hasan, B A and Eckert, J (2020) Study of thermal and structural characteristics of mechanically milled nanostructured Al-Cu-Fe quasicrystals. Materials Chemistry and Physics, 251 (IF-3.408). p. 123071.

Ali, Tayyab and Venkataraman, A (2013) Preparation and characterization of g-Fe2O3 dispersed polyvinyl alcohol (PVA) Nanocomposite film. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 293-297.

Ali, Tayyab and Venkataraman, A (2014) Synthesis and characterization of polyaniline coated functionalized g-Fe O nanoparticles. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 35-39.

Altekar, V A (1981) National Metallurgical Laboratory. In: International Symposium on Modern Developments in Steel making, February 15, 1981, NML, Jamshedpur.

Altekar, V A (1975) Some problems of technology transfer in India. NML Technical Journal, 17 (3-4). pp. 9-12.

Altekar, V A and Shahani, M J and Saha, A K (1974) Adsorption of nickel by lignite. Fuel, 53 (1). pp. 29-31.

Altekar, V A and Singh, S R and Rao, G N and Virdhi, P S and Dash, R R (1978) Melting trials with cast-iron boring briquettes in cupola and arc furnace. Transactions of the Indian Institute of Metals, 31 (3). pp. 221-223.

Ananda Kumar, S and Meenakshi, K Shree and Narasimhan, B R V and Srikanth, S and Arthanareeswaran, G (2009) Synthesis and characterization of copper nanofluid by a novel one-step method. Materials Chemistry and Physics, 113 . pp. 57-62.

Ananda Kumar, S and Sundara Raman, S Ganesh and Sankara Narayanan, T S N and Gnanamoorthy, R (2012) Fretting wear behaviour of surface mechanical attrition treated alloy 718. Surface and Coatings Technology, 206 . pp. 4425-4432.

Anantharaman, T R (1997) The Iron Pillar at Delhi. In: Iron and Steel Heritage of India, November, 1997, IIM & Tata Steel, Jamshedpur.

Anil, M and Srivastava, V C and Ghosh, M K and Ojha, S N (2010) Influence of tin content on tribological characteristics of spray formed Al–Si alloys. Wear, 268 (11-12). pp. 1250-1256.

Anjaneyulu, Ch and Murty, B S (2017) Soft magnetic properties of Fe-based bulk metallic glass system containing niobium and copper. Journal of Metallurgy and Materials Science, 59(3) . pp. 103-110.

Aruna, V A J and Ravi, B P and Haran, N P and Ram, Mohan and Gundewar, C S (2013) Recovery of phosphate from lean resources. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 209-217.

Arunagiri, S and Venkataraman, G (1976) Creep rupture failures in superheater tubes of high pressure boilers. NML Technical Journal, 18 (4). pp. 81-86.

Ashok, K and Sankar, P and Maruthupandian, K (2013) Process Evaluation of AOD Stainless Steel Making In Salem Steel Plant, SAIL. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

B

Babu, M Nani and Sahu, K K and Pandey, B D and Mankhand, T R (2004) Kinetics of leaching of zinc from sphalerite concentrate with sodium persulphate. Canadian Metallurgical Quarterly , 43 (3). pp. 321-328.

Bacon, N H (1958) Segregation and Internal Weakness in Forging Ingots. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Bagchi, M and Akerkar, D D (1977) Selective separation and extraction of nickel from ammoniacal leach liquors using a chelating agent. Transactions of the Indian Institute of metals, 30 (3). pp. 177-179.

Bagchi, R K and Bandhu, Vishva (2013) Technology in Secondary Steel Sector. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Bagui, S and Narasaiah, N and Bar, H N and Das, Swapan K and Parida, N and Upadhyay, A K and Sharma, R K (2011) Evaluation of Center Buffer Coupler. Sponsored (SSP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Bagui, S and Ray, Ashok K and Sahu, J K and Parida, N and Swaminathan, J and Tamilselvi, M and Mannan, S L (2013) Influence of Saline Environment on creep rupture life of Nimonic-263 for marine turbine application. Material Science and Engineering A-Stuctural Materials properties Microstructure and processing, 566 (IF-2.003). pp. 54-60.

Bagui, Sumanta and Laha, K and Mitra, R and Tarafder, S (2018) Accelerated creep behavior of Nb and Cu added 18Cr-8Ni austenitic stainless steel. Materials Research Express, 5 . p. 116515.

Bahadur, Aruna (1996) Aluminum coatings for steel. Materials and Manufacturing Processes, 11 (2). pp. 225-232.

Bahadur, Aruna (1987) Behavior of Al-Mg alloys at high-temperature. Journal of Materials Science, 22 (6). pp. 1941-1944.

Bahadur, Aruna (1981) Dendritic cell-size - its growing importance. Transactions of the Indian Institute of metals, 34 (3). pp. 229-233.

Bahadur, Aruna (1998) Development and evaluation of a low chromate corrosion inhibitor for cooling water systems. Canadian Metallurgical Quarterly, 37 (5). pp. 459-468.

Bahadur, Aruna (1993) Effect of ph on corrosion inhibition of mild-steel by chromates. Materials Transactions JIM, 34 (12). pp. 1191-1194.

Bahadur, Aruna (2003) Enhancement of high temperature strength and room temperature ductility of iron aluminides by alloying. Materials Science and Technology, 19 (12). pp. 1627-1634.

Bahadur, Aruna (1988) Intermetallic phases in Al-Mn alloys. Journal of materials science, 23 (1). pp. 48-54.

Bahadur, Aruna (1996) Low chromate corrosion inhibitor with borate and hexametaphosphate. Materials Transactions JIM, 37 (4). pp. 605-611.

Bahadur, Aruna (1998) Partial substitution of chromate by borate for cooling water inhibition. ISIJ International, 38 (5). pp. 469-473.

Bahadur, Aruna (1985) Radio isotopes as a tool in metallurgical research and industry. Transactions of the Indian Institute of metals, 38 (4). pp. 301-308.

Bahadur, Aruna (1998) Study of Film Growth on Copper in Chromate Solution by a Radioactive Tracer Technique. Journal of Materials Science Letters, 17 (8). pp. 701-704.

Bahadur, Aruna and Kumar, Rajendra (1972) A study of solidification of aluminum and aluminum-copper alloys by anodic oxidation technique. Metallography, 5 (3). pp. 275-284.

Bahadur, Aruna and Maji, K D and Kumar, Rajendra (1975) Analysis of alloys and salt-solutions by beta-ray backscattering. Journal of applied chemistry and biotechnology, 25 (7). pp. 515-522.

Bahadur, Aruna and Mitra, A and Ravi Kumar, B and Palit Sagar, S (2007) Evaluation and Correlation of Residual Stress Measurement in Steel. Evaluation and Correlation of Residual Stress Measurement in Steel , 26 (2-4). pp. 47-55.

Bahadur, Aruna and Mohanty, O N (1995) Aluminum diffusion coatings on medium-carbon steel. Materials Transactions JIM, 36 (9). pp. 1170-1175.

Bahadur, Aruna and Mohanty, O N (1991) The Development of FE-AL Intermetallics. Journal of Materials Science, 26 (10). pp. 2685-2693.

Bahadur, Aruna and Mohanty, O N (1990) Structural studies of calorized coatings on mild-steel. Materials Transactions JIM, 31 (11). pp. 948-953.

Bahadur, Aruna and Mohanty, O N (1991) Structural studies of hot dip aluminized coatings on mild-steel. Materials Transactions JIM, 32 (11). pp. 1053-1061.

Bahadur, Aruna and Prasad, R S (1992) Anodic etching technique for observation of microstructural change during the solidification and precipitation process in al-cu alloy. Journal of Materials Science Letters, 11 (20). pp. 1349-1352.

Bahadur, Aruna and Ravi Kumar, B and Ghosh Chowdhury, S (2003) Effect of Thermomechanical Treatment on X-Ray Elastic Constants and Residual Stresses in HSLA-100 Steel. Journal of Nondestructive Evaluation, 22 (2). pp. 53-62.

Bahadur, Aruna and Ravi Kumar, B and Kumar, A Seshu and Sarkar, G G and Rao, J S (2004) Development and comparison of residual stress measurement on welds by various methods. Materials Science and Technology, 20 (2). pp. 261-269.

Bahadur, Aruna and Ravi Kumar, B and Mohanty, O N (1995) Ductility improvement in iron aluminides. Journal of Materials Science, 30 (14). pp. 3690-3696.

Bahadur, Aruna and Sharma, T L and Parida , N and Mukherjee, A N and Mohanty, O N (1993) Structure-property correlation in al-diffusion coated steels. Journal of Materials Science, 28 (19). pp. 5375-5381.

Bahl, O P and Mathur, R B and Dwivedi, Hariom (1998) Correlation between the Surface Energetics of Reinforcement and Mechanical Properties of Carbon/Carbon Composites. In: UNSPECIFIED.

Bairwa, Rajdeep and Kishore, Kaushik (2011) Analysis of strain hardening behaviour of high performance TWIP,TRIP and FBDP Steels-I. Training Report (TR). National Metallurgy Laboratory, Jamshedpur. (Submitted)

Balasubramani, N and Srinivasan, A and Pillai, U T S and Raghukandan, K and Pal, B C (2008) Effect of antimony addition on the microstructure and mechanical properties of ZA84 magnesium alloy. Journal of Alloys and Compounds, 455 (1-2). pp. 168-173.

Balasubramani, N and Suresh, M and Srinivasan, A and Pillai, U T S (2007) Observation of the suppression of Mg17Al12 formation in a La-containing AZ91 alloy. Journal of Materials Science, 42 (19). pp. 8374-8376.

Balasubramanian, Krishnan (2011) NDE Tools for process and product monitoring in manufacturing. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Ballal, N B and Kadri, Irfan and Kothari, Anil Kumar and Viswanathan, N N (2013) Modelling of Processes in the Trickling Zone of the Iron Blast Furnace. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Balon, R and Poos, A (1963) Experience with a hundred percent pellet burden and a low slag volume. NML Technical Journal, 5 (2). pp. 17-24.

Balusamy, T and Sankara Narayanan, T S N and Ravichandran, K and Park, Song and Lee, Min Ho (2013) Effect of surface mechanical attrition treatment (SMAT) on pack boronizing of AISI 304 stainless steel. Surface and Coatings Technology, 232 (IF-1.941). pp. 60-67.

Balusamy, T and Sankara Narayanan, T S N and Ravichandran, K and Park, Song and Lee, Min Ho (2013) Pack boronizing of AISI H11 tool steel: Role of surface mechanical attrition treatment. Vacuum, 97 (IF-1.530). pp. 36-43.

Balusamy, T and Sankara Narayanan, T S N and Ravichandran, K and Park, Song and Lee, Min Ho (2013) Plasma nitriding of AISI 304 stainless steel: Role of surface mechanical attrition treatment. Materials Characterization, 85 (IF-1.880). pp. 38-47.

Balusamy, T and Venkateswarlu, M and Murthy, K S N and Vijayanand, S and Sankara Narayanan, T S N (2014) Effect of Surface Mechanical Attrition Treatment (SMAT) on the Surface and Electrochemical Characteristics of Pb-Sn Alloy. International Journal of Electrochemical Science, 9(1) (IF-1.956). pp. 96-108.

Bandopadhyay, A and Ganguly, Amit and Gupta, K N (1996) Investigations on the anomalous oxidation behaviour of high-carbon gas-based direct reduced iron (DRI). Thermochimica Acta, 276 . pp. 199-207.

Bandyopadhyay, D and Chakravorty, N (1993) A study on the kinetics of iron-oxide reduction by solid carbon. Steel Research, 64 (7). pp. 340-345.

Bandyopadhyay, D and Ghosh, Arindam (1996) Validity of rate equation based on Langmuir-Hinshelwood mechanism for gasification of carbon - A reappraisal. Steel Research, 67 (3). pp. 79-86.

Bandyopadhyay, D and Pathak, L C and Mukherjee, I and Das, S K and Ganguly, R G and Ramachandrarao, P (1997) Fabrication of Al2O3-SiCw in situ composite through a new combustion technique. Materials Research Bulletin, 32 (1). pp. 75-82.

Bandyopadhyay, D and Singh, S D and Sanyal, D and Singh, K N (2003) A study on dissolution kinetics of carbon in liquid iron bath. Chemical Engineering Journal, 94 (2). pp. 79-92.

Banerjee, Arunima and Sivaprasad, S (2012) Fracture and Deformation Behaviour of Materials. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Banerjee, G and Pal, T K and Das, Goutam (2009) Performance Evaluation of Resistance Spot Welded Interstitial Free Steel Under Cryogenic Conditions. Journal of Testing And Evaluation, 37 (6). pp. 566-572.

Banerjee, K and Roy, Nilima and Ghosh, R N and Chatterjee, U S (2004) Strain rate dependence of plastic flow behaviour of HSLA-100 steel in seawater during cathodic charging of hydrogen. Transactions of the Indian Institute of Metals, 57 (6). pp. 611-616.

Banerjee, M K and Mukherjee, A N and Pandey, J L and Bhattamishra, A K (1991) Studies on Active-Passive Transition behaviour of Stainless Steels. NML Technical Journal, 33 (3-4). pp. 10-17.

Banerjee, M K and Singh, Inder and Nag, P S and Mukherjee, K P (1994) Effect of cold deformation and hydrogen charging on ttf and hardness of 0.1 c steel. Anti-corrosion methods and materials, 41 (2). pp. 10-12.

Banerjee, P K (1994) An Overview of Manufacturing Methods of Tin Hell Buck Plate ('IMBP) and its Quality Requirements. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Banerjee, S (1997) Indigenous Steel Technology of India : What we could learn from it. In: Iron and Steel Heritage of India, November 1997, IIM & Tata Steel, Jamshedpur.

Banerjee, T (1969) Theory on mechanism of phase-transformation in electrolytic alloys. NML Technical Journal, 11 (1). pp. 4-5.

Bansal, A and Sinha, Arvind (2012) Dehydration driven changes in the structure and mechanical behavior of electrospun poly (vinyl alcohol) nanofibers. Materials Science and Engineering: C, 32 (3). pp. 587-593.

Bansal, G K and Chandan, A K and Ghosh, C and Srivastava, V C and Dutta, Monojit and Ghosh Chowdhury, S (2021) The Pros and Cons of an Energy-Efficient Q&P Approach to Develop Advanced Steels. Next Generation Materials and Processing Technologies, Part of the Springer Proceedings in Materials book series (SPM, volume 9) . pp. 15-26.

Bansal, G K and Chandan, A K and Mandal, G K and Srivastava, V C (2020) High Entropy Alloys: An Overview on Current Developments" in the book "High Entropy Alloys: Innovations, Advances, and Applications. High Entropy Alloys: Innovations, Advances, and Applications (Book). pp. 1-68.

Bansal, G K and Chandan, A K and Srivastava, V C and Gopalakrishna, K and Das, Goutam and Rajkumar, S and Ghosh Chowdhury, S and Tarafder, S (2021) Studies on Tensile Behaviour of Selective Laser Melted 316L Stainless Steel Using SEM Straining Stage. Transactions of the Indian National Academy of Engineering . pp. 1-11.

Bansal, G K and Ghosh, C and Rajinikanth, V and Ghosh Chowdhury, S (2021) Effect of Finish Rolling Temperature on Microstructure and Mechanical Properties of Low-Si Steel After Quenching and Nonisothermal Partitioning. Transactions of the Indian Institute of Metals .

Bansal, G K and Jena, P S M and Ghosh, C and Srivastava, V C and Rajnikanth, V and Dutta, Monojit and Ghosh Chowdhury, S (2020) Quench Temperature-Dependent Mechanical Properties During Nonisothermal Partitioning. Metallurgical and Materials Transactions A, 51A (IF-2.050). pp. 5088-5100.

Bansal, G K and Rajnikanth, V and Ghosh, Chiradeep and Srivastava, V C and Dutta, Monojit and Ghosh Chowdhury, S (2020) Effect of cooling rate on the evolution of microstructure and mechanical properties of nonisothermally partitioned steels. Materials Science and Engineering: A, 788 (IF-4.652). p. 139614.

Bansal, G K and Sahoo, Biraj and Chandan, A K (2020) Metallurgical Perspective on Quench and Partitioned Advanced High Strength Steels. Steel Tech, 14(4) (NonSCI). pp. 60-64.

Bar, H N and Parida, N and Palit Sagar, S and Ghosh, R N (2007) Evaluation of Prototype Horton Sphere using Acoustic Emission. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Bar, H N and Sahu, J K and Parida, N and Gunjan, M K (2011) Failure Investigation of Components of Aero Engine No. HDR-80376U. Other (TMP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Bar, H N and Sivaprasad, S and Narasaiah, N and Paul, S K and Sen, B N and Chandra, Sanjay (2013) Low Cycle and Ratchetting Fatigue Behavior of High UTS/YS Ratio Reinforcing Steel Bars. Journal of Materials Engineering and Performance, 22(6) (IF- 0.92). pp. 1701-1707.

Baral, Jayashree (2011) Creep characterization of Boron added P91 steel in the temperature range 600 - 650 degree C. Masters thesis, National Metallurgical Laboratory (NML).

Baral, Jayashree and Swaminathan, J and Chakrabarti, D and Ghosh, R N (2015) Creep behavior of P91B steel in the presence of a weld joint. Materials Science and Engineering A, 631 (IF-2.409). pp. 220-229.

Baral, Jayashree and Swaminathan, J and Ghosh, R N (2013) Creep Behaviour of 9CrMoNbV (P91) Steel having a Small Amount of Boron. Procedia Engineering, 55 . pp. 88-92.

Barat, K and Bar, H N and Mandal, D and Roy, H and Sivaprasad, S and Tarafder, S (2014) Low temperature tensile deformation and acoustic emission signal characteristics of AISI 304LN stainless steel. Materials Science and Engineering A, 597 (IF-2.409). pp. 37-47.

Barat, K and Metya, A and Sathpathy, S and Sivaprasad, S and Tarafder, S and Kar, Sujoy Kumar (2015) Ultrasonic quantification of high temperature cyclic damage in an advanced nickel based superalloy. Materials Science and Engineering A, 625 (IF-2.409). pp. 194-204.

Barat, Kaustav and Sivaprasad, S and Kar, Sujoy Kumar and Tarafder, S (2020) A novel rate based methodology for creep fatigue life estimation of superalloys. International Journal of Pressure Vessels and Piping, 182 (IF-2.230). p. 104064.

Barman, H and Hamada, A S and Sahu, T and Mahato, B and Talonen, J and Shee, S K and Sahu, Puspendu and Porter, D A and Karjalainen, L P (2014) A Stacking Fault Energy Perspective into the Uniaxial Tensile Deformation Behavior and Microstructure of a Cr-Mn Austenitic Steel. Metallurgical and Materials Transaction A, 45A(4) (IF-1.730). pp. 1937-1952.

Barraclough, K C (1958) The Effects of Hydrogen on Alloy Steel Production. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Basak, A C and Ghosh, K C and Paul, A R and Bhattacharjee, S and Pandey, L P (1995) A review on thiocyanate methods for the estimation of molybdenum by molecular absorption spectroscopy. Talanta, 42 (4). pp. 497-506.

Basak, A C and Ghosh, K C and Sircar, J K and Paul, A R and Pandey, L P and Bhattacharjee, S (1996) A Sensitive Method for the Determination of Silicon by Molecular Absorption Spectroscopy. Microchemical Journal, 54 (1). pp. 48-53.

Basak, G (1980) Distillation of zinc .2. Studies on lead content in distilled zinc dust. Transactions of the Indian Institute of metals, 33 (4). pp. 327-328.

Basak, P and Dev, S C and Dubey, R K (1986) Process parameters in the development of Ag-AgCdO composites-Study and standardisation. NML Technical Journal, 28 (1-4). pp. 30-36.

Basanth Kumar, K and Saxena, Kuldeep K and Dey, Suhash R and Pancholi, Vivek and Bhattacharjee, A (2016) Microstructural evolution in hot compressed TiHy 600 titanium alloy. Journal of Metallurgy and Materials Science, 58(3) (IF 0.04). pp. 147-152.

Basariya, M R and Roy, Rajat K and Pramanick, A K and Srivastava, V C and Mukhopadhyay, N K (2015) Structural transition and softening in Al-Fe intermetallic compounds induced by high energy ball milling. Materials science and engineering a-structural materials properties microstructure and processing, 638 (IF-2.567). pp. 282-288.

Basariya, M R and Srivastava, V C and Mukhopadhyay, N K (2015) Comparative Studies on Al-Based Composite Powder Reinforced with Nano Garnet and Multi-wall Carbon Nanotubes. Journal of Materials Engineering and Performance, 24(11) (IF-0.998). pp. 4200-4205.

Basariya, M R and Srivastava, V C and Mukhopadhyay, N K (2014) Microstructural characteristics and mechanical properties of carbon nanotube reinforced aluminum alloy composites produced by ball milling. Materials & Design, 64 (IF-3.171). pp. 542-549.

Basavaraja, C (2015) Microwave absorption studies of polyaniline nanocomposites containing Poly (2-acrylamido-2- methyl-1-propanesulfonicacid)/graphene nanoplatelet. Journal of Metallurgy and Materials Science, 57(3) . pp. 135-141.

Basavaraja, C (2015) Partially degradable electrically conductive poly (3,4-ethylenedioxy-thiophene)/sigma cellulose polymer composites. Journal of Metallurgy and Materials Science, 57(4) . pp. 251-255.

Basavaraja, C and Kumar, K B Satish and Vishnuvardhan, T K (2014) Hony comb patterns and DC conductivity of cellulose multiwalled carbon nanotube composite films. Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 209-215.

Basoalto, H C and Ardakani, M and Ghosh, R N and Mclean, M (2002) Multiaxial lifetime predictions of single-crystal superalloys: Use of reference stresses. Materials and Manufacturing Processes, 17 (4 (Special Issue)). pp. 519-528.

Basu, A and Majumdar, J Dutta and Ghosh Chowdhury, S and AjiKumar, P K and Tyagi, A K and Baldevraj, and Manna, I (2007) Microstructural and texture studies of gas-nitrided Cr-coated low-alloy high-carbon steel. Surface and Coatings Technology, 201 (16-17). pp. 6985-6992.

Basu, Bikramjit and Mishra, Suman K (2006) Development of toughened zirconia composites ceramics for tribological application. Grant in Aid (GAP). CSIR-NML, Jamshedpur. (Submitted)

Basu, D K and Bhattamishra, A K and Dev, S C and Singh, Inder (1995) Studies on corrosion behavior of Cu-Si alloys in sulfide and chloride media. Anti-corrosion Methods & Materials, 42 (5). pp. 14-16.

Basu, Projjal and Sarkar, S B and Ray, H S (1989) Isothermal reduction of coal mixed iron-oxide pellets. Transactions of The Indian Institute of Metals, 42 (2). pp. 165-172.

Bera, S and Ghosh Chowdhury, S and Lojkowsky, W and Manna, I (2012) Synthesis of CuCr and CuCrAg alloys with extended solid solubility with nano-Al2O3 dispersion by mechanical alloying and consolidation by high pressure sintering. Materials Science and Engineering : A, 558 (IF-2.003). pp. 298-308.

Bera, Supriya and Ghosh Chowdhury, S and Estrin , Yuri and Manna, I (2013) Mechanical properties of Al7075 alloy with nano-ceramic oxide dispersion synthesized by mechanical milling and consolidated by equal channel angular pressing. Journal of Alloys and Compounds, 548 (IF-2.390). pp. 257-265.

Berg, Frenk van den and Yang, Haibing (2011) Real-time Meniscus Level and Slag Thickness Measurement by RADAR. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Berg, Frenk van den and Yang, Haibing (2011) Real-time Meniscus Level and Slag Thickness Measurement by RADAR. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Berlia, Rohit and Ghosh Chowdhury, S (2012) Mechanical behaviour of TWIP steels:effect of grain size and composition. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Bhadani, S N and Tewari, M and Agrawal, A and Sekhar, K C (1994) Extraction-spectrophotometric determination of nickel as ni-(par)(2)-(ctab)(2) complex in polymetallic sea-bed nodules and steels. Fresenius journal of analytical chemistry, 349 (6). pp. 478-481.

Bhadani, S N and Tewari, M and Agrawal, A and Sekhar, K C (1998) Extractive-photometric determination of cobalt(II) in steels using 4-(2-pyridylazo)resorcinol and xylometazoline hydrochloride. Journal of the indian chemical society, 75 (3). pp. 176-177.

Bhadani, S N and Tiwari, M and Agrawal, A and Kavipurapu, C S (1994) Spectrophotometric determination of fe(iii) with tiron in the presence of cationic surfactant and its application for the determination of iron in al-alloys and cu-based alloys. Mikrochimica Acta, 117 (1-2). pp. 15-22.

Bhagat, A N and Ranganathan, S and Mohanty, O N (2003) Electrical resistivity studies in low carbon and HSLA-100 steels. Materials Science and Technology, 19 (3). pp. 343-346.

Bhagat, R P (1999) Factors affecting return sinter fines regimed and strand productivity in iron ore sintering. ISIJ International, 39 (9). pp. 889-895.

Bhagat, R P (1999) Kinetics of sodium dodecyl benzene sulfonate adsorption on hematite. Scandinavian Journal of Metallurgy, 28 (4). pp. 156-161.

Bhagat, R P (1999) Replacement of coke breeze by Leco-fines from Neyveli in iron ore sintering. Transactions of the indian institute of metals, 52 (5). pp. 299-304.

Bhagat, R P (1996) Settling test and size determination - Loading effect in settling of unflocculated particles and their size distribution. Scandinavian journal of metallurgy, 25 (2). pp. 48-50.

Bhagat, R P (1992) Studies on calcination of limestone and its assimilation by hematite during the sintering using thermo-gravimetric and x-ray-diffraction analyses. Scandinavian Journal of Metallurgy, 21 (6). pp. 246-250.

Bhagat, R P (2015) Study on utilisation coal fines generated in sponge iron making through pelletisation. Journal of Metallurgy and Materials Science, 57(3) . pp. 143-149.

Bhagat, R P and Dey, Shobhana (1999) Flocculation of iron ore slimes from Joda and Kiriburu mines. Indian journal of chemical technology, 6 (5). pp. 280-284.

Bhagat, R P and Nayak, B and Bhattacharyya, K K and Goswami, M C (2014) Mineralogy of iron ore pellet and its correlation with crushing strength. Journal of Metallurgy and Materials Science, 56(2) (NON-SCI). pp. 117-123.

Bhagat, R P and Pathak, P N (1997) Effect of solid concentration on settling rate of granite ore slimes. Transactions of the Indian Institute of Metals, 50 (2-3). pp. 209-212.

Bhagat, R P and Ray, H S and Gupta, Saibal Kanti (1991) Improvement in Performance of Blast Furnace at Bhilai through Statistical Analysis and Improvement in Burden Preparation. ISIJ International, 31 (7). pp. 669-676.

Bhagat, R P and Schieder, D and Immler, J and Dobias, B (1997) Adsorption of H+/OH- and sulfonate ions on hematite. Metals Materials and Processes, 8 (4). pp. 323-328.

Bhaskar Raju, G and Karuppiah, M T and Latha, S S and Parvathy, S and Prabhakar, S (2008) Treatment of wastewater from synthetic textile industry by electrocoagulation-electrooxidation. Biochemical Engineering Journal, 144 (1). pp. 51-58.

Bhaskar Raju, G and Khangaonkar, P R (1982) Electro-flotation of chalcopyrite. International Journal of Mineral Processing, 9 . pp. 133-143.

Bhaskar Raju, G and Khangaonkar, P R (1982) Electro-flotation of chalcopyrite fines. International Journal of Mineral Processing, 9 (2). pp. 133-143.

Bhaskar Raju, G and Khangaonkar, P R (1984) Electroflotation of chalcopyrite fines with sodium diethyldthiocarbamate as collector. International Journal of Mineral Processing, 13 . pp. 211-221.

Bhaskar Raju, G and Prabhakar, S and Sankaran, C (1993) Beneficiation of iron-ores by column flotation. Transactions of the institution of mining and metallurgy section c-mineral processing and extractive metallurgy, 102 ( ). C132-C135.

Bhatnagar, S S and Guha, B K and Sinha, R K (1979) Vanadium high-strength low-alloy steels for low-temperature use. Journal of Materials Science, 14 (7). pp. 1631-1640.

Bhattacharjee, A K and Mahanta, B Cmu and Mukherjee, K K and Rout, M K (1986) Relative acidity of 5-hydroxyperinaphthindane-1,3-dione. Journal of the Indian Chemical Society, 63 (4). pp. 406-407.

Bhattacharjee, A K and Singh, Inder (1995) A mathematical account of marine corrosion behaviour of galvanised steel structures installed in Digha coast of Bay of Bengal. Indian Journal of Marine Sciences, 25 (3). pp. 280-281.

Bhattacharjee, A K and Singh, Inder (1995) Studies on the presence of copper in the galvanized coating on weathering steel and the adherence characteristic of the protective copper complex formed on galvanized weathering steel. Journal of materials science, 30 (6). pp. 1617-1620.

Bhattacharjee, PP and Tsuji, N (2012) Development of Cube Texture in Pure Ni Following Ultrahigh by Accumaulative Roll Bonding and Annealing. Materials Science Forum, 715-716 . 521- .

Bhattacharjee, S (1993) Geometric volume and new refrigerants—I. Halomethanes. Computers & Chemistry, 17 (4). pp. 383-388.

Bhattacharjee, S (1995) Geometric volume and new refrigerants—II. Haloethanes. Computers & Chemistry, 19 (1). pp. 51-58.

Bhattacharjee, S (1994) Haloethanes, geometric volume and atomic contribution method. Computers & Chemistry, 18 (4). pp. 419-429.

Bhattacharjee, S and Basak, A C and Dasgupta, P (1992) Molecular property correlation in haloethanes with geometric volume. Computers & Chemistry, 16 (3). pp. 223-228.

Bhattacharjee, S and Bhattacharyya, G and Mitra, A (2003) Chronological development of heavy metal accumulation research in earthworms - A review. Journal of Metallurgy and materials Science, 45 (1). pp. 19-37.

Bhattacharjee, S and Chakravarty, S and Maity, S and Dureja, V and Gupta, K K (2005) Metal contents in the groundwater of Sahebgunj district, Jharkhand, India, with special reference to arsenic. Chemosphere, 58 (9). pp. 1203-1217.

Bhattacharjee, S and Chakravarty, S and Maity, S and Kar, S and Thakur, P and Bhattacharyya, G (2003) Removal of lead from contaminated water bodies using sea nodule as an adsorbent. Water Research, 37 (16). pp. 3954-3966.

Bhattacharjee, S and Chatterjee, N N and Gupta, K K (1990) Gpack-i - an application software for drawing calibration curves. Computers & Chemistry, 14 (3). pp. 247-248.

Bhattacharjee, S and Dasgupta, P (1994) Molecular property correlation in alkanes with geometric volume. Computers & Chemistry, 18 (1). pp. 61-71.

Bhattacharjee, S and Dasgupta, P and Jha, S N and Rao, A S and Gupta, K K and Pandey, L P (1993) Computational elimination of interelemental interference in the analysis of copper, cobalt and nickel in polymetallic sea bed nodules by flame atomic absorption spectrometry. Talanta, 40 (5). pp. 675-680.

Bhattacharjee, S and Dasgupta, P and Paul, A R and Ghosal, S and Padhi, K K and Pandey, L P (1998) Mineral element composition of spinach. Journal of the science of food and agriculture, 77 (4). pp. 456-458.

Bhattacharjee, S and Gupta, K K (1992) A new technique for surface optimization. Computers & Chemistry, 16 (3). pp. 229-232.

Bhattacharjee, S and Gupta, K K and Chakravarty, S and Thakur, P and Bhattacharyya, G (2005) Separation of iron, nickel, and cobalt from sulphated leach liquor of low nickel lateritic oxide ore. Separation Science and Technology, 39 (2). pp. 413-429.

Bhattacharjee, S and Kar, S and Chakravarty, S (2004) Mineral compositions of Datura: A traditional tropical medicinal plant. Communications in Soil Science and Plant Analysis, 35 (7-8). pp. 937-946.

Bhattacharjee, S and Rao, A S and Dasgupta, P (1991) A new index for molecular property correlation in halomethanes. Computers & chemistry, 15 (4). pp. 319-322.

Bhattacharjee, S and Roy, Nilima and Dey, A K and Banerjee, M K (1993) Statistical appraisal of the atmospheric corrosion of mild steel. Corrosion Science, 34 (4). pp. 573-581.

Bhattacharya, A K (1992) Observation of dendritic cavities in “nickel-free” austenitic stainless steel. Journal of Materials Science Letters, 11 (1). pp. 26-28.

Bhattacharya, A K and Parida, N and Gope, P C (1992) Monitoring hydrogen embrittlement cracking using acoustic emission technique. Journal of Materials Science, 27 ( 6). pp. 1421-1427.

Bhattacharya, D K (1995) Characterisation of microstructure in steels by magnetic techniques - An overview. Transactions of the indian institute of metals, 48 (6). pp. 495-513.

Bhattacharya, D K (1995) Microstructure of Welded Joints. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory (CSIR), Jamshedpur.

Bhattacharya, D K (2003) NDT for residual life assessment in Indian industry. Insight, 45 (1). pp. 31-40.

Bhattacharya, D K (2001) Non-Destructive Techniques for Microstructural and Structural Characterisation. In: UNSPECIFIED.

Bhattacharya, D K (1994) Testing Methods for Heat Treated Steel Products. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Bhattacharya, D K and Vaidyanathan, S (1997) Effect of the demagnetisation factor on the Barkhausen noise signal. Journal of Magnetism and Magnetic Materials, 166 (1-2). pp. 111-116.

Bhattacharya, J (1975) Cold extrusion of copper powder. Metallurgia and metal forming, 42 (2). p. 36.

Bhattacharya, J and Ghosh, B N and Banerjee, S K (1984) Differential deformation during roll bonding of stainless-steel to aluminum sheet. Transactions of the Indian Institute of metals, 37 (5). 552-&.

Bhattacharya, J and Ghosh, B N and Chaudhury, S K and Chakraborty, S and De , P K and Mohanty, O N (1992) Structure property correlation in thermo-mechanically processed ultra high-carbon steel. Scandinavian Journal Of Metallurgy, 21 (6). pp. 279-283.

Bhattacharya, S and Dhar, S and Das, S K and Ganguly, Ranjan and Webster, T J and Nayar, S (2014) Colloidal graphite/graphene nanostructures using collagen showing enhanced thermal conductivity. International Journal of Nanomedicine, 9 (IF-4.195). pp. 1287-1298.

Bhattacharya, S and Jenamoni, K and Nayar, S (2012) Stability of biomimetic ferrofluids established by a systematic study using microwave irradiation at defined wattages. Journal of Magnetism and Magnetic Materials, 324 (20). pp. 3261-3266.

Bhattacharya, S and Roychowdhury, Anirban and Das, D and Nayar, S (2015) Multi-functional biomimetic graphene induced transformation of Fe3O4 to ε-Fe2O3 at room temperature. RSC Advance (IF-3.84). pp. 89488-89497.

Bhattacharya, Soumya and Mishra, Swati and Gupta, P and Pranav, P and Ghosh, M and Pramanick, A K and Mishra, D P and Nayar, S (2015) Liquid phase collagen modified graphene that induces apoptosis. RSC Advances, 5(55) (IF-3.84). pp. 44447-44457.

Bhattacharya, Soumya and Roychowdhury, Anirban and Tiwari, V and Prasad, A B Krishna and Ningthoujam, R S and Patel, A B and Das, Dipankar and Nayar, S (2015) Effect of biomimetic templates on the magneto-structural properties of Fe3O4 nanoparticles. RSC Advances, 5(18) (IF-3.708). pp. 13777-13786.

Bhattacharyya, A S and Das, G C and Mukherjee, S and Mishra, Suman K (2009) Effect of radio frequency and direct current modes of deposition on protective metallurgical hard silicon carbon nitride coatings by magnetron sputtering. Vacuum, 83 (12). pp. 1464-1469.

Bhattacharyya, A S and Mishra, Suman K (2011) Micro/nanomechanical behavior of magnetron sputtered Si-C-N coatings through nanoindentation and scratch tests. Journal of Micromechanics and Microengineering, 21 (1). 015011.

Bhattacharyya, A S and Mishra, Suman K and Mukherjee, S (2010) Correlation of structure and hardness of rf magnetron sputtered silicon carbonitride films. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 28 (4). pp. 505-509.

Bhattacharyya, A S and Mishra, Suman K and Mukherjee, Surojit and Das, G C (2009) A comparative study of Si–C–N films on different substrates grown by RF magnetron sputtering. Journal of Alloys and Compounds, 478 (1-2). pp. 474-478.

Bhattacharyya, P (2021) Conducting-Polymer-Based Supercapacitors. In: Handbook of Nanocomposite Supercapacitor Materials III. Springer Fachmedien Wiesbaden GmbH, Germany. ISBN ISBN: 978-3-030-68363-4

Bhattamishra, A K (1992) Observation of dendritic cavities in nickel-free austenitic stainless-steel. Journal of Materials Science Letters, 11 (1). pp. 26-28.

Bhattamishra, A K (2006) Study of hot-dip galvanised zinc and zinc-copper alloy coatings in chloride and chloride containing carboxylic acids media. Journal of Metallurgy and Materials Science, 48 (4). pp. 215-220.

Bhattamishra, A K and Banerjee, M K (1993) Corrosion behavior of al-zn-mg alloys in nacl solution in presence of cerium salts. Zeitschrift fur metallkunde, 84 (10). pp. 734-736.

Bhattamishra, A K and Basu, D K (2001) A comparative study on the performance of inhibitors for protection of recirculating cooling water system. Journal of Metallurgy and materials Science, 43 (2). pp. 141-145.

Bhattamishra, A K and Chattoraj, I and Basu, D K and De, P K (2000) Study on the influence of the Si/Fe ratio on the corrosion behaviour of some Al-Fe-Si alloys. Zeitschrift Fur Metallkunde, 91 (5). pp. 393-396.

Bhattamishra, A K and Lal, Kishori (1998) Influence of ageing on corrosion behaviour of Al-Mg-Si alloys in chloride and acid media. Zeitschrift fur metallkunde, 89 (11). pp. 793-796.

Bhattamishra, A K and Lal, Kishori (1997) Microstructural studies on the effect of Si and Cr on the intergranular corrosion in Al-Mg-Si alloys. Materials & Design, 18 (1). pp. 25-28.

Bhattamishra, A K and Mishra, G S and Banerjee, M K (1992) On the effect of misch metal addition on corrosion behavior of aluminum in inorganic and organic-acids. Zeitschrift Fur Metallkunde, 83 (10). pp. 766-768.

Bhende, Vinay P (1963) Development Planning in under developed countries. NML Technical Journal, 5 (4). pp. 4-10.

Bhoray, S S and Sampath, V S and Bhatnagar, P P (1969) Studies on desilication of siliceous bauxite from Kashmir. NML Technical Journal, 11 (2). pp. 30-35.

Bid, S and Sahu, Puspendu and Pradhan, S K (2007) Microstructure characterization of mechanosynthesized nanocrystalline NiFe2O4 by Rietveld's analysis. Physica E: Low-dimensional Systems and Nanostructures, 39 (2). pp. 175-184.

Bishop, Tom (1958) Recent Developments in Alloy and Special Steels in Great Britain. In: Symposium on Production, Properties & Applications of Alloy & Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Biswal, Vivekananda and Soni, Sunny and Jena, D P and Kumar, Rajesh (2008) Application of image processing in estimation of area of heat affected zone. Journal of Metallurgy and Materials Science, 50 (4). pp. 219-225.

Biswas, A and Nistala, Harsha and Sinha, Moni (2015) Effect of flux granulometry on the sintering process using thermodynamic analysis. Journal of Metallurgy and Materials Science, 57(2) . pp. 67-74.

Biswas, D K and Ashana, S R and Rau, V G (2003) Some studies on energy savings in sponge iron plants. Journal Of Energy Resources Technology-Transactions Of The, 125 (3). pp. 228-237.

Biswas, D K and Asthana, S R and Rau, V G (2001) Pollution management with techno-economic evaluation for coke based and cokeless cupolas. Applied Thermal Engineering, 21 (3). pp. 359-379.

Biswas, Nabonita and Ghosh, T K and Mukherjee, Rajesh and Rao, S Mohan (2013) Exploiting iron values from iron ore source rock: Opportunities. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 305-311.

Biswas, P K (1998) Manufacturing Processes of Polymer Matrix Composite Material for Aerospace Application. In: UNSPECIFIED.

Biswas, P K and Godiwalla, K M and Sanyal, D (2002) A simple technique for measurement of apparent viscosity of slurries: sand–water system. Materials & Design, 23 (5). pp. 511-519.

Biswas, P K and Godiwalla, K M and Sanyal, D and Dev, S C (2002) A simple technique for measurement of apparent viscosity of slurries: sand-water system. Materials & Design, 23 (5). pp. 511-519.

Biswas, Piyalee and Das, S and Sarkar, Paromita and Choudhary, Kamal and Baidya, Prasanta and Giri, P and Ghosal, A and Bandyopadhyay, A K (2013) Rectificaton of Energy transport in nonlinear metamaterials via ratchets. Journal of Physics D-Applied Physics, 46(20) (IF-2.528).

Biswas, S C (1958) Practical Problems in the Manufacture of Alloy Steel. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Biswas , P K (1994) Tailoring of Properties through Squeeze Castic Technique. In: Tailoring of Properties through Squeeze Casting Technique, 23-24, September 1994, NML, Jamshedpur.

Biswas , P K and Dev, S C and Krishnan, C S S (1998) Some Critical Issues in the Processing of Magnesium Alloys & Composites. In: UNSPECIFIED.

Bjorling, G and Elfstrom, N G (1962) Electrolytic Manganese in a Non-Diaphragm Cell. NML Technical Journal, 4 (1). pp. 30-32.

Bodas, M G and Akerkar, D D (1991) Extraction of nickel and cobalt from over-burden sample of chromite ore mines of orissa mining corporation. Transactions of the Indian Institute of Metals, 44 (6). pp. 433-440.

Bodas, M G and Akerkar, D D and Altekar, V A (1979) Thermal-decomposition of manganese carbonate for the production of manganese-dioxide. Transactions of the Indian Institute of Metals, 32 (5).

Bodas, M G and Bagchi, D and Akerkar, D D (1988) Characterization and leaching studies of the manganese residue generated in the treatment of polymetallic sea nodules. Transactions of the Indian Institute of metals, 41(6) . pp. 615-617.

Bodas, M G and Mathur, S B (1997) Studies in reduction-roast leaching ion exchange of copper converter slag from an Indian copper complex, Ghatshila. Industrial & Engineering Chemistry Research, 36 (12). pp. 5419-5424.

Booth, N (1960) Pilot Plants in Pyrometallurgy. NML Technical Journal, 2 (1). pp. 47-51.

Bose, A K (1995) Development of high-temperature aluminous mortar. Transactions of the indian institute of metals, 48 (2). pp. 115-119.

Bose, B C and Choudhury, V N and Pandey, L P (1980) Simultaneous complexometric determination of iron and calcium in phosphate rock. Indian journal of chemistry section A-Inorganic bio-inorganic physical theoretical & analytical chemistry, 19 (2). pp. 180-181.

Bose, S C and Roy, Nilima and Ghosh, R N (2009) Probabilistic creep life assessment of austenitic stainless steel. In: NMD - ATM 2009, November 14, 2009 to November 17, 2009, Science City Complex,Kolkata, India.

Bose, S C and Singh, K and Sarma, D S (2008) Effect of service simulated ageing on microstructure and creep rupture properties of I CrMoV (Casing Casting) steel vis-a-vis remnant life assessment in view of latent creep strength. In: UNSPECIFIED.

Bose, S C and Singh, K and Swaminathan, J and Sarma, D S (2004) Prediction of creep life of X10CrMoVNbN-91 (P-91) steel through short term stress relaxation test methodology. Materials Science and Technology, 20 (10). pp. 1290-1296.

Bose, S K and Altekar, V A (1982) Studies on iron reduction of stibnite by x-ray diffraction and scanning electron microscopy. NML Technical Journal, 24 (1-2). pp. 5-7.

Bose, S K and Altekar, V A (1980) Thermal-reaction in the iron reduction of stibnite. Transactions of the Indian Institute of Metals, 33 (3). pp. 201-203.

Bose, S K and Gupta, R D and Kumar, Rajendra (1987) Transformation characteristics of supersaturated aluminium-chromium solid-solution. Transactions of the Indian Institute of metals, 40 (5). pp. 389-393.

Bose, S K and Kumar, Rajendra (1973) Structure of rapidly solidified aluminum-silicon alloys. Journal of materials science, 8 (12). pp. 1795-1799.

Brisby, M D J (1960) The Development of a Steel Industry-Factors Affecting the Econonmics of Steel. NML Technical Journal, 2 (1). pp. 36-46.

Bucknall, E H (1958) Alloy Steels- Technical and Economic Background. In: Symposium on Production , Properties & Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Budhani, R K (1976) Creep resistant steels for the heavy electrical industry. NML Technical Journal, 18 (4). pp. 63-68.

Bui, Q V and Nam, N D and Choi, D H and Lee, J B and Lee, C Y and Kar, Abhijit and Kim, J G and Jung, S B (2010) Corrosion protection of ENIG surface finishing using electrochemical methods. Materials Research Bulletin, 45 (3). pp. 305-308.

Bui, Q V and Nam, N D and Yoon, J W and Choi, D H and Kar, Abhijit and Kim, J G and Jung, S B (2011) Effect of Gold on the Corrosion Behavior of an Electroless Nickel/Immersion Gold Surface Finish. Journal of Electronic Materials, 40 (9). pp. 1937-1942.

C

Cadambe, V (1958) Application of Alloy Steels to Aircraft Industry. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Calla, O P N and Rathore, Inder Singh (2011) Complex dielectric constant measurement of glass epoxy and zinc oxide at temperature ranging from -1960C to +2000C at microwave frequencies. Journal of Metallurgy and Materials Science, 53 (2). pp. 161-173.

Callender, W (1959) Studies in the Sintering Permeability and Pellet Strength of Australian Hematite Ores. NML Technical Journal, 1 (1). pp. 47-58.

Chakrabarti, Kaushik and Sarkar, B and Ashok, V D and Das, K and Chaudhuri, S S and Mitra, A and De, S K (2014) Exchange bias effect in BiFeO3-NiO nanocomposite. Journal of Applied Physics, 115(1) (IF-2.185). 013906.

Chakraborty, Dolly and Ranganathan, S and Sinha, S N (2010) Carbothermic Reduction of Chromite Ore Under Different Flow Rates of Inert Gas. Metallurgical and Materials Transactions B, 41 (1). pp. 10-18.

Chakraborty, Dolly and Ranganathan, S and Sinha, S N (2003) Kinetics of reduction of chromium in chromite ore. Transactions Of The Indian Institute Of Metals , 56 (4). pp. 335-339.

Chakraborty, J (2014) Diffraction stress analysis of fiber textured Ti thin films undergoing hcp - fcc phase transformation. International Confrence on Residual Stresses 9 (ICRS 9), 768-769 . pp. 257-263.

Chakraborty, J (2021) Lattice expansion and phase stability in nanocrystalline titanium thin films. Philosophical Magazine Letters, 101(8) . pp. 330-340.

Chakraborty, J and Das, Swapan K and Rao, Venkatesh and Sinha, Arvind (2003) Behaviour of iron ion in the morphosynthesis of magnetite particles. Materials Transactions , 44 (6). pp. 1124-1127.

Chakraborty, J and Ghosh, M and Ranjan, R and Das, Goutam and Das, D and Chandra, Sanjay (2013) X-ray diffraction and Mossbauer spectroscopy studies of cementite dissolution in cold-drawn pearlitic steel. Philosophical Magazine, 93(36) . pp. 4598-4616.

Chakraborty, J and Maiti, Tias and Ghosh, M and Das, Goutam and Chandra, Sanjay (2014) Cementite dissolution in cold drawn pearlitic steel wires: role of dislocations. International Confrence on Residual Stresses 9 (ICRS9), 768-769 . pp. 304-312.

Chakraborty, Jay and Kumar, Kishor and Ranjan, R and Ghosh Chowdhury, S and Singh, S R (2010) Stress, Texture and Phase Transformation in Titanium Thin Films. Texture and Anisotropy of Polycrystals, 160 . pp. 109-116.

Chakraborty, Jay and Kumar, Kishor and Ranjan, Rajeev and Ghosh Chowdhury, S and Singh, S R (2011) Thickness-dependent fcc–hcp phase transformation in polycrystalline titanium thin films. Acta Materialia, 59 (7). pp. 2615-2623.

Chakraborty, Jui and Nayar, S and Singh, T B and Bhattacharyya, D and Sinha, Arvind (2004) Templated growth of mesoporous aluminum phosphate tubules using protein molecules of tobacco. Journal of Materials Science, 39 (1). pp. 285-288.

Chakraborty, M (2011) Chemical Synthesis and Characterization of Nickel Powder. Metallurgical and materials transactions B-Process metallurgy and materials processing science, 42 (2). pp. 380-384.

Chakraborty, M and Ghosh, M and Das, S K and Mahato, B (2009) Synthesis and characterization of superparamagnetic Co & CoNi particles. In: TMS 2009 138th Annual Meeting & Exhibition - Supplemental Proceedings, Feb, 2009, TMS.

Chakraborty, M and Srikanth, S (2000) Kinetics of salt roasting of chalcopyrite using KCl. Thermochimica Acta, 362 (1-2). pp. 25-35.

Chakraborty, S K (2015) E-waste recycling. Journal of Metallurgy and Materials Science, 57(2) . pp. 107-113.

Chakraborty, S P and Chaudhury, S K and Dubey, R K (1978) Ausrolling of spring steel for automotive applications. Transactions of the Indian Institute of Metals, 31 (5-6). pp. 420-423.

Chakraborty, S P and Choudhury, S K and De, P K and Dubey, R K (1986) Some observations on hot-forging characteristics of iron-powder preforms. NML Technical Journal, 28 (1-4). pp. 26-29.

Chakraborty, S P and Dubey, R K and Gupte, P K (1971) Some observations on ausforming of high-carbon, high-chromium die steel. NML Technical Journal, 13 (2). pp. 52-57.

Chakravarty, S and Bhattacharjee, S and Gupta, K K and Singh, Manjit and Chaturvedi, Hema T and Maity, S (2007) Adsorption of zinc from aqueous solution using chemically treated newspaper pulp. Bioresource Technology, 98 (16). pp. 3136-3141.

Chakravarty, S and Dureja, V and Bhattacharyya, G and Maity, S and Bhattacharjee, S (2002) Removal of arsenic from groundwater using low cost ferruginous manganese ore. Water Research, 36 (3). pp. 625-632.

Chakravarty, S and Mohanty, Ashok and Nag, Sudha T and Upadhyay, A K and Konar, J and Sircar, J K and Madhukar, A and Gupta, K K (2010) Removal of Pb(II) ions from aqueous solution by adsorption using bael leaves (Aegle marmelos). Journal of Hazardous Materials, 173 (1-3). pp. 502-509.

Chakravarty, S and Pimple, S and Chaturvedi, Hema T and Singh, S and Gupta, K K (2008) Removal of copper from aqueous solution using newspaper pulp as an adsorbent. Journal of Hazardous Materials, 159 (2-3). pp. 396-403.

Chakravorty, M and Paramguru, R K and Sircar, J K and Jena, P K (1997) Electro-dissolution of nichrome in hydrochloric acid. Bulletin of Electrochemistry, 13 (6). pp. 269-274.

Chalavadi, G and Singh, R K and Sharma, Mamta and Singh, Ratnakar and Das, Avimanyu (2016) Development of a Generalized Strategy for Dry Beneficiation of Fine Coal over a Vibrating Inclined Deck. International Journal of Coal Preparation and Utilization, 36(1) (IF-0.673). pp. 10-27.

Chandan, A K and Sahoo, Biraj K and Bansal, G K (2021) Medium Manganese Steel: A Promising Candidate for Automotive Applications. Steel Tech, 15(2) . pp. 60-66.

Chandan, A K and Tripathy, S and Sen, B and Ghosh, M and Ghosh Chowdhury, S (2021) Temperature dependent deformation behavior and stacking fault energy of Fe40Mn40Co10Cr10 alloy. Scripta Materialia, 199 (IF-5.079). p. 113891.

Chandwani, R and Timbrell, C M and Wiehahn, M A (2008) Crack modelling in power plant components. In: UNSPECIFIED.

Charles, J A (1959) Iron Pretreatment Research. NML Technical Journal, 1 (1). pp. 68-79.

Chatterjea, A B (1974) International-Symposium on Science and Technology of Sponge Iron and Its Conversion to Steel. Journal of Scientific & Industrial Research, 33 (1). pp. 7-9.

Chatterjea, A B and Nijhawan, B R and Goswami, J and Biswas, S K and Singh, Santokh R and Padan, J S (1967) Production of pig iron from Andhra Pradesh raw materials. NML Technical Journal, 9 (1). pp. 16-22.

Chatterjee, B and Roy, P L (1992) Some Observations on the Selection of Ceramic Shell Mould Materials for Investment Casting. NML Technical Journal, 34 (3-4). pp. 9-16.

Chatterjee, G P (1958) Development of Creep-Resistant Alloy Steels. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Chatterjee, P and Banerjee, M K and Mukherjee, K P (1991) Synergistic inhibition of inorganic anions with pyridine-derivatives for steel in hydrochloric-acid. Indian Journal of Technology, 29 (4). pp. 191-194.

Chatterjee, Partho Pratim (2014) Embryonic improvements of solar photovoltaics. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 67-72.

Chatterjee, Partho Pratim (2015) Generation of piezoelectric potential difference from solar energy induced thermo-mechanical stress. Journal of Metallurgy and Materials Science, 57(1) . pp. 19-25.

Chatterjee, S and Bhagat, A N and Gope , N (2002) Development of Semi-Processed Steels for Electrical Lamination Applications at Tata Steel. In: Proceedings of Seminar on Resurgence of Metallic Materials the Current Scenario(ROMM-2002), Oct. 24 & 25, 2002, National Metallurgical Laboratory(CSIR), Jamshedpur.

Chattopadhyay, Lalitha (1996) Size effect on crack-tip creep. Engineering Fracture Mechanics, 53 (2). pp. 309-310.

Chattopadhyay, Lalitha (1995) Size effect on plastic energy dissipation during stable crack growth. Engineering Fracture Mechanics, 51 (4). pp. 697-700.

Chattopadhyay, R and Guha, B K and Bhatnagar, S S (1968) The effect of normalising on the properties of low carbon vanadium-niobium-nitrogen structural steels. NML Technical Journal, 10 (1). pp. 10-14.

Chattopadhyay, S (1988) A mathematical-modeling of the thermal profile of an ESR Ingot during controlled cooling. Transactions of the Indian Institute of metals, 41 (4). pp. 349-356.

Chattoraj, I (1995) The effect of hydrogen-induced cracking on the integrity of steel-components. Sadhana-academy proceedings in engineering sciences, 20 ( ). pp. 199-211.

Chattoraj, I (1993) The effect of near-crystallization temperature annealing on the electrochemical behavior of amorphous Fe77.5B15Si7.5 fibres in borate buffer. Scripta Metallurgica et Materialia, 29 (5). pp. 611-616.

Chattoraj, I (1995) Hydrogen-induced cracking on the integrity of steel-components. Sadhana-Academy Proceedings In Engineering Sciences, 20 . pp. 199-211.

Chattoraj, I (2001) Notch Effects in Corrosive Failure. In: UNSPECIFIED.

Chattoraj, I (1997) Stepwise cracking in a longitudinally welded steel linepipe. Transactions of the Indian Institute of Metals, 50 (1). pp. 97-102.

Chattoraj, I and Bhattamishra, A K and Joarder, A and Bhattacharya, D K (1995) Identification of the corrosion mechanism in a boiler drum by corrosion product analysis. Anti-corrosion methods and materials, 42 (3). pp. 4-6.

Chattoraj, I and Bhattamishra, A K and Mitra, A (1992) The effect of corrosion on the magnetic properties of papidly solidified Fe-Si-B amorphous fibres. Scripta Metallurgica et Materialia, 26 (7). pp. 1013-1017.

Chattoraj, I and Bhattamishra, A K and Mitra, A (1993) Polarization and resistivity measurements of post-crystallization changes in amorphous Fe-B-Si alloys. Corrosion, 49 (9). pp. 707-713.

Chattoraj, I and Das, Swapan K and Jana, S and Chakraborty, S P and Bhattamishra, A K (1995) Passivity breakdown due to discontinuous precipitation during aging of 21Cr-1oMn-5Ni stainless-steel. Journal of Materials Science, 30 (20). pp. 5313-5320.

Chattoraj, I and Joarder, A and Bhattamishra, A K and Bhattacharya, D K and Ghosh, R N (1997) Crevice attack of a boiler steam drum. Canadian Metallurgical Quarterly, 36 (2). pp. 143-148.

Chattoraj, I and Kumar, A and Das, Swapan K and Tarafder, Mita and Tarafder, S (2003) Factors influencing the extent of hydrogenenhanced brittle cracking in a Cu-strengthened HSLA steel during monotonic loading. Zeitschrift Fur Metallkunde , 94 (11). pp. 1228-1233.

Chattoraj, I and Mitra, A (1996) Micromagnetic studies on hydrogenated steel. In: Trends in NDE science and technology - Proceedings of the 14th world conference on NDT, 1996, 14th WCNDT.

Chattoraj, I and Mitra, A (1998) Structure-electrochemical correlations in amorphous and devitrified Fe-based ferromagnetic alloys. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Chattoraj, I and Pathak, L C (1998) Electrochemical behavior of superconducting Bi1.4Pb0.6Sr2Ca2Cu3O10 in halide-containing acetate buffer. Corrosion Science, 54 (6). pp. 435-443.

Chattoraj, I and Wilde, B E (1992) The effect of shot peening on calculated hydrogen surface coverage of AISI 4130 steels. Scripta Metallurgica et Materialia, 26 (1). pp. 89-94.

Chaudhary, P N (2009) Extractive Metallurgy. In: A Continuing Education Course on Metallurgy for Engineers, December 14-16, 2009, NML, Jamshedpur.

Chaudhary, S K (2003) An innovative solution for deterioration of railway track. Journal of Metallurgy and Materials Science . pp. 45-53.

Chaudhuri, S (2008) Creep and life assessment of engineering components in power plants and process industries. In: UNSPECIFIED.

Chaudhuri, S (1994) Heat Treatment of Stainless Steels. In: Workshop on Heat Treatment & Surface Engineering of Iron & Steels(HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Chaudhuri, S (2008) Philosophy of integrity assessment of engineering components. Materials Science and Engineering: A, 489 (1-2). pp. 259-266.

Chaudhuri, S (1993) Some aspects of creep behaviour of 2.25 Cr-1Mo Steel. PhD thesis, IIT Kharagpur.

Chaudhuri, S and Ghosh, R N (2009) Creep Behavior Of 2.25cr1mo Steel-Effects Of Thermal Ageing And Pre-Strain. Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing , 510-11 (sl. lss). pp. 136-141.

Chaudhuri, S and Ghosh, R N (1998) Some aspects of mechanisms and modelling of creep behaviour of 2.25Cr-1Mo steel. ISIJ International, 38 (8). pp. 881-887.

Chaudhuri, S and Roy, Nilima and Ghosh, R N (2008) Assessment of creep and rupture behavior of 2.25Cr-1Mo steel – A strain-based approach and its limitation. In: 5th International Conference on Creep, Fatigue and Creep-Fatigue Interaction, September 24-26, 2008, Kalpakkam.

Chaudhuri, S and Roy, Nilima and Ghosh, R N (1993) Modelling high temperature creep of Cr---Mo steel. Acta Metallurgica et Materialia, 41 (1). pp. 273-278.

Chaudhury, S K and Singh, A K and Sivaramakrishnan, C S and Panigrahi, S C (2004) Preparation and thermomechanical properties of stir cast Al-2Mg-11TiO2 (rutile). Bulletin of Materials Science, 27 (6). pp. 517-521.

Chaudhury, S K and Singh, A K and Sivaramakrishnan, C S and Panigrahi, S C (2005) Wear and friction behavior of spray formed and stir cast Al–2Mg–11TiO2 composites. Wear, 258 (5-6). pp. 759-767.

Chaudhury, S K and Singh, A K and Sivaramakrishnan, C S and Panigrahi, S C (2004) Tensile and fracture behavior of spray formed and stir cast Al–2Mg–TiO2 composites. Materials Science and Engineering A, 374 (1-2). pp. 184-190.

Chaudhury, S K and Sivaramakrishnan, C S and Panigrahi, S C (2004) A new spray forming technique for the preparation of aluminium rutile (TiO2) ex situ particle composite. Journal of Materials Processing Technology, 145 (3). pp. 385-390.

Chennakesavulu, K and Basariya, M R and Sreedevi, P and Bhaskar Raju, G and Prabhakar, S and Subba Rao, S (2011) Study on thermal decomposition of calix[4]arene and its application in thermal stability of polypropylene. Thermochimica Acta, 515 (1-2). pp. 24-31.

Chennakesavulu, K and Bhaskar Raju, G and Prabhakar, S and Nair, C M and Murthy, K V G K (2009) Adsorption Of Oleate On Fluorite Surface As Revealed By Atomic Force Microscopy. International Journal of Mineral Processing, 90 (1-4). pp. 101-104.

Chesters, J H (1960) The Encouragement of Productive Research. NML Technical Journal, 2 (4). pp. 24-26.

Chetal, S C and Sabharwal, M C (1976) Design basis and materials requirements for sodium heated steam generators for fast reactors. NML Technical Journal, 18 (4). pp. 73-80.

Chidambaram, S and Kamaraj, A (2017) Failure investigation of an industrial crankshaft made of ductile iron. Advances in natural and applied sciences, 11(8) . pp. 25-30.

Chokshi, Yakshil and Dutta, S K (2013) Production of Iron Ore-Coal Composite Briquette/Pellet by Using Fly-Ash and Other Binders. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Choubey, R and Banerjee, T (1969) Standardisation and design criteria relating to high temperature tensile and creep properties. NML Technical Journal, 11 (1). pp. 17-22.

Choubey, R and Das, M R (1972) An analysis of procedure for acceptance creep testing of ferritic low alloy steels for high temperature service. NML Technical Journal, 14 (4). pp. 137-140.

Choubey, R and Gibbons, T B and Prasad, K (1977) Creep-properties and microstructure of austenitic steels containing manganese. Metals technology, 4 (issue:Nov). pp. 524-529.

Choudhary, B N and Roy, B N and Vaish, A K (2015) Production of foundry grade iron from sponge iron fines. Journal of Metallurgy and Materials Science, 57(4) . pp. 211-224.

Choudhary, B N and Roy, B N and Vaish, A K and Singh, S D (2014) Smelting of sponge iron fines for the production of steel grade iron. Journal of Metallurgy and Materials Science, 15(2) (NON-SCI). pp. 107-116.

Choudhury, Deepak and Mittal, Kapil (2012) A metallurgical investigation of microstructure of the weld bead in submerged arc welding. Journal of Metallurgy and Materials Science, 54(4) . pp. 311-320.

Choudhury, S B and Khan, Z H and Nag, P S (1979) Investigation of stress corrosion cracking in mild steel stainless steel and brass by stress relaxation technique. NML Technical Journal, 21 (3-4). pp. 30-36.

Choudhury, Samrat Sen and Bhattacharjee, S (2011) Application of an aqueous nanometric aluminum oxide suspension for fluoride remediation. Journal of Metallurgy and Materials Science, 53 (4). pp. 355-367.

Choudhury, V N and Mukherjee, B C and Bose, B C and Pandey, L P (1980) Simultaneous chelatometric determination of calcium and magnesium in magnesite. Indian Journal of Technology, 18 (1). pp. 45-46.

Chowdhury, A and Bijalwan, P K and Sahu, Ranjan K (2014) Investigations on the role of alkali to obtain modulated defect concentrations for Cu2O thin films. Applied Surface Science, 289 (IF-2.538). pp. 430-436.

Chowdhury, T and Sivaprasad, S and Bar, H N and Tarafder, S and Bandyopadhyay, N R (2015) Cyclic fracture behaviour of 20MnMoNi55 steel at room and elevated temperatures. Fatigue & Fracture of Engineering Materials & Structures, 38 (IF-1.561). pp. 813-827.

Chowdhury, T and Sivaprasad, S and Bar, H N and Tarafder, S and Bandyopadhyay, N R (2015) Incremental cyclic fracture behaviour of 20MnMoNi55 steel at room temperature. International Journal of Fracture, 192(1) (IF-1.348). pp. 117-132.

Chvoj, Z and Srikanth, S and Ramachandrarao, P (1999) Thermodynamic limits and kinetic probabilities during homogeneous nucleation in liquid Ag-Cu alloys. Journal of non-equilibrium thermodynamics, 24 (4). pp. 360-371.

Cicalé, C and Abbruzzese, G and Fortunati , S (2013) Historical Development, Present Status and Future of Electrical Steel. In: Proceedin of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Coheur, P (1959) On the Bottom Blown Processes and the LD-AC Process. NML Technical Journal, 1 (1). pp. 105-114.

Colclough, T P (1959) Developments in Blast Furnace Practice. NML Technical Journal, 1 (1). pp. 59-67.

Crafts, Walter and Hilty, D C (1958) Deoxidation and Inclusion Control for Alloy Steel. In: Symposium on Production, Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

CSIR, (2010) CSIR Technofest - 2010: Theme 12: Mining, Minerals & Materials. In: CSIR Technofest - 2010, 14-27 November, 2010, New Delhi. (Unpublished)

D

Dadhich S, Devesh and Sahu, Ranjan K (2012) Study of Photocatalytic degradation of Congo red pollutants using microwave derived SrFe12O19. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Dadhich S, Devesh and Sahu, Ranjan K (2012) Study of Transition Element doped Oxide based Permanent Magnets. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Das, Samar (1995) Specimen Preparation for Electron Microscopy. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Das, Anindya (2011) High Strain Rate Tensile Deformation of Low Carbon Steels (OLP-0160). Masters thesis, National Metallurgical Laboratory (NML).

Das, Arpan (2015) Crystallographic variant selection of martensite at high stress/strain. Philosophical Magazine, 95(20) (IF-1.427). pp. 2210-2227.

Das, Arpan (2015) Crystallographic variant selection of martensite during fatigue deformation. Philosophical Magazine, 95(8) (IF-1.427). pp. 844-860.

Das, Arpan (2015) Dislocation configurations through austenite grain misorientations. International Journal of Fatigue, 70 (IF-2.665). pp. 473-479.

Das, Arpan (2014) Magnetic properties of cyclically deformed austenite. Journal of Magnetism and Magnetic Materials, 361 (IF-2.002). pp. 232-242.

Das, Arpan (2013) Martensite–Void Interaction. Scripta Materialia, 68(7) (IF-2.821). pp. 514-517.

Das, Arpan (2014) Slip System Activity During Cyclic Plasticity. Metallurgical and Materials Transactions A, 45 A (7) (IF-1.730). pp. 2927-2930.

Das, Arpan and Chakraborti, P C and Tarafder, S and Bhadeshia, H K D H (2011) Analysis of deformation induced martensitic transformation in stainless steels. Materials Science and Technology, 27 (1). pp. 366-370.

Das, Arpan and Chowdhury, T and Tarafder, S (2014) Ductile fracture micro-mechanisms of high strength low alloy steels. Materials & Design, 54 (IF-3.171). pp. 1002-1009.

Das, Arpan and Das, Swapan K and Tarafder, S (2009) Correlation of Fractographic Features with Mechanical Properties in Systematically Varied Microstructures of Cu-Strengthened High-Strength Low-Alloy Steel. Metallurgical and Materials Transactions A, 40 (13). pp. 3138-3146.

Das, Arpan and Poddar, Palash (2013) Structure–wear-property correlation. Materials & Design, 47 (IF-2.913). pp. 557-565.

Das, Arpan and Roy, Nilima and Ray, Ashok K (2014) Stress induced creep cavity. Materials Science and Engineering A, 598 (IF-2.409). pp. 28-33.

Das, Arpan and Sivaprasad, S and Chakraborti, P C and Tarafder, S (2011) Connection between deformation-induced dislocation substructures and martensite formation in stainless steel. Philosophical Magazine Letters Online ISSN 1362-3036, 91 (10). pp. 664-675.

Das, Arpan and Sivaprasad, S and Chakraborti, P C and Tarafder, S (2008) Correspondence of fracture surface features with mechanical properties in 304LN stainless steel. Materials Science and Engineering: A, 496 (1-2). pp. 98-105.

Das, Arpan and Sivaprasad, S and Chakraborti, P C and Tarafder, S (2011) Morphologies and characteristics of deformation induced martensite during low cycle fatigue behaviour of austenitic stainless steel. Materials Science and Engineering A, 528 (27). pp. 7909-7914.

Das, Arpan and Sivaprasad, S and Tarafder, Mita and Das, S K and Tarafder, S (2013) Estimation of Damage in high strength steels. Applied Soft Computing, 13(2) (IF-2.140). pp. 1033-1041.

Das, Arpan and Tarafder, S (2009) Experimental investigation on martensitic transformation and fracture morphologies of austenitic stainless steel. International Journal of Plasticity, 25 (11). pp. 2222-2247.

Das, Arpan and Tarafder, S and Chakraborti, P C (2011) Estimation of deformation induced martensite in austenitic stainless steels. Materials Science and Engineering A, 529 (1). pp. 9-20.

Das, B N and Choubey, R and Goswami, K C (1960) Wear and Friction under Rolling with Slip. NML Technical Journal, 2 (4). pp. 15-21.

Das, Bhaskar and Hossain, S M and Pakhira, B and Pramanick, A K and Das, Rahul and Ray, M (2020) Fluorescence quenching based detection of p-nitrophenol using luminescent silicon nanocrystals and insights into the quenching mechanism. Semiconductor Science and Technology, 35(3) (IF-2.361). 035003 .

Das, C R and Albert, S K and Laha, K and Swaminathan, J and Ravi, S and Bhaduri, A K and Murty, B S and Mayer, P (2014) Influence of Coincidence Site Lattice Boundary on Creep Resistance of P91 Steel Weldments. Procedia Engineering, 86 (NIF-0.629). pp. 80-87.

Das, C R and Albert, S K and Swaminathan, J and Bhaduri, A K and Murty, B S (2013) Effect of Boron on Creep Behaviour of Inter-critically Annealed Modified 9Cr-1Mo Steel. Procedia Engineering, 55 . pp. 402-407.

Das, C R and Albert, S K and Swaminathan, J and Raju, S and Bhaduri, A K and Murty, B S (2012) Transition of Crack from Type IV to Type II Resulting from Improved Utilization of Boron in the Modified 9Cr-1Mo Steel Weldment. Metallurgical and Materials Transactions A, 43A . pp. 3724-3741.

Das, Goutam and Das, Mousumi and Ghosh, Sabita and Dubey, A K (2010) Effect of aging on mechanical properties of 6063 Al-alloy using instrumented ball indentation technique. Materials Science and Engineering: A, 527 (6). pp. 1590-1594.

Das, Goutam and Das, Mousumi and Sinha, Satish and Gupta, K K and Chakravarty, S and Ray, Ashok K (2009) Characterization of cast stainless steel weld pools by using ball indentation technique. Materials Science and Engineering: A, 513-514 . pp. 389-393.

Das, Goutam and Ghosh, Sabita and Sahay, S K (2005) Use of ball indentation technique to determine the change of tensile properties of SS316L steel due to cold rolling. Materials Letters, 59 (18). pp. 2246-2251.

Das, Goutam and Ghosh, Sabita and Sahay, S K and Ranganath, V R and Vaze, K K (2003) Development and validation of ball indentation technique to evaluate the mechanical properties of materials. Transactions Of The Indian Institute Of Metals , 56 (5). pp. 465-475.

Das, Goutam and Ghosh, Sabita and Sahay, S K and Ranganath, V R and Vaze, K K (2004) Influence of pre-straining on mechanical properties of HSLA steel by using ball indentation technique. Zeitschrift Fur Metallkunde, 95 (12). pp. 1120-1127.

Das, Goutam and Rao, V and Joarder, A and Mohanty, O N and Murthy, S G N and Mitra, A (1995) Magnetic characterization of 5cr-0.5Mo steel used in-process heater tubes. Journal of Physics D-Applied Physics, 28 (11). pp. 2229-2234.

Das, Goutam and Rao, Venkatesh and Joarder, A and Mohanty, O N and Murthy, S G N and Mitra, A (1995) Magnetic characterization of 5Cr-0.5Mo steel used in process 1 heater tubes. Journal of Physics D: Appl. Phys., 28 . pp. 2229-2234.

Das, H K and Basak, Sushovan and Das, Goutam and Pal, T K (2013) Influence of Energy Induced from Processing Parameters on the Mechanical Properties of friction stir welded lap joint of Aluminium to Coated Steel Sheet. The International Journal of Advanced Manufacturing Technology, 64(9-12) (IF-1.205). pp. 1653-1661.

Das, K P and Ganguly, S and Chattopadhyay, P P and Tarafder, S and Bandopadhyay, N R (2009) Exploring The Possibilities Of Development Of Directly Quenched TRIP-Aided Steel By The Artificial Neural Networks (ANN) Technique. Materials and Manufacturing Processes, 24 (1). pp. 68-77.

Das, L N (1985) High-accuracy temperature-measurement in creep testing of steels. Research and Industry, 30 (4). pp. 424-428.

Das, L N (1994) Ultrasonic acoustic transducers for underwater acoustic measurements. Ocean Technology Perspectives , 47 (1). pp. 57-66.

Das, L N and Kumar, S and Agadi, W and Das, V K and Desai, B N (1994) Ultrasonic acoustic transducers for underwater acoustic measurements. Ocean Technology Perspectives . pp. 625-629.

Das, M R and Gibbons, T B (1976) Diffusion creep in low-alloy steels. Scripta Metallurgica, 10 (3). pp. 231-233.

Das, Mousumi and Das, Goutam (2011) Role of dynamic precipitation on the strengthening mechanism of cryorolled 6063 Al alloy. Transactions of the Indian Institute of Metals, 64 (1-2). pp. 75-79.

Das, Mousumi and Das, Goutam and Ghosh, M and Wegner, Matthias and Rajnikanth, V and Ghosh Chowdhury, S and Pal, T K (2012) Microstructures and mechanical properties of HPT processed 6063 Al alloy. Materials Science and Engineering A, 558 (IF-2.108). pp. 525-532.

Das, Mousumi and Pal, T K and Das, Goutam (2012) Effect of aging and cryo rolling on microstructural chara-cterization and mechanical properties of precipitation hardenable 6063Al alloy. Material Science & Engineering, 552 (30). pp. 31-35.

Das, Mousumi and Pal, T K and Das, Goutam (2012) Use of Portable Automated Ball Indentation System to Evaluate Mechanical Properties of Steel Pipes. Transactions of the Indian Institute of Metals, 65 (2). pp. 197-203.

Das, N and Pandey, M C and Ghosh, R N (1998) High temperature creep behaviour of single crystal superalloy. Material Science and Technology, 14 (5). pp. 429-434.

Das, N and Singh, K K and Maiti, H S (2002) Preparation of alumina membranes for micro- and ultrafiltration applications. British Ceramic Transactions, 101 (5). pp. 208-212.

Das, N K and Mahanti, R K and Sivaramakrishnan, C S and Kumar, Rajendra (1982) Effect of 2-phase solidification on fracture-toughness of aluminum-alloys. Indian Journal of Technology, 20 (11). pp. 434-437.

Das, N K and Balasundaram, L J (1971) Some Experiences in Melting with Electron Beam Melting Furnace. NML Technical Journal, 13(3) . pp. 83-86.

Das, N N and Dash, A and Brahama, G S and Mohapatra, P (2003) Synthesis, characterisation and dissociation of a glycinate bridged trinuclear Co(III)-Cu(II)-Co(III) complex. Inorganic Reaction Mechanisms , 5 (1). pp. 73-77.

Das, N N and Jana, R K (2006) Adsorption of some bivalent heavy metal ions from aqueous solutions by manganese nodule leached residues. Journal of Colloid and Interface Science, 293 (2). pp. 253-262.

Das, N N and Konar, J and Mohanta, M K and Srivastava, V C (2004) Adsorption of Cr(VI) and Se(IV) from their aqueous solutions onto Zr4+-substituted ZnAl/MgAl-layered double hydroxides: effect of Zr4+ substitution in the layer. Journal of Colloid and Interface Science, 270 (1). pp. 1-8.

Das, N N and Konar, J and Mohanta, M K and Upadhyay, A K (2010) Synthesis, characterization and adsorptive properties of hydrotalcite-like compounds derived from titanium rich bauxite. Reaction Kinetics, Mechanisms and Catalysis, 99 (1). pp. 167-176.

Das, N N and Pattanaik, Pragyan and Das, Rita (2005) Defluoridation of drinking water using activated titanium rich bauxite. Journal of Colloid and Interface Science, 292 (1). pp. 1-10.

Das, N N and Samal, Amrendra (2004) Synthesis, characterisation and rehydration behaviour of titanium(IV) containing hydrotalcite like compounds. Microporous and Mesoporous Materials, 72 (1-3). pp. 219-225.

Das, S K and Biswas, A and Ghosh, R N (1993) Volume fraction dependent particle coarsening in plain carbon steel. Acta Metallurgica et Materialia, 41 (3). pp. 777-781.

Das, S K and Chatterjee, M K (1993) Specific surfaces and heat of adsorption of some Indian clays by dye-adsorption technique. Bulletin of Materials Science, 16 (3). pp. 205-211.

Das, S K and Daspoddar, P K (1997) Dehydration kinetics of hydrated calcium dialuminate. Thermochimica Acta, 293 (1-2). pp. 125-128.

Das, S K and Godiwalla, K M and Mehrotra, S P and Dey, P K and Mandal, D and Hegde, Shubha (2006) Mathematical modelling of ductile erosion behaviour of impacted fly ash particles on steel components of a coal fired boiler. In: 60 Annual Technical Meeting, November, 15-16 2006, IIM & Tata Steel,Jamshedpur.

Das, S K and Godiwalla, K M and Mehrotra, S P and Dey, P K and Mandal , D and Hegde, Shubha (2006) Mathematical Modelling of ductile erosion behaviour of impacted fly ash particles on steel components of coal fired boiler. In: 60 Annual Technical Meeting, November, 15-16, 2006, NML, Jamshedpur.

Das, S K and Kumar, Sanjay and Daspoddar, P K (1997) Crystal morphology of calcium aluminates hydrated for 14 days. Journal of Materials Science Letters, 16 (9). pp. 735-736.

Das, S K and Kumar, Sanjay and Poddar, P K D (1997) Effect of synthetic refractory aggregates on the hydraulic and other properties of commercial high alumina cement. Industrial Ceramics, 17 (1). pp. 17-22.

Das, Samar and Ghosh, Arindam and Kundu, Sukumar and Chatterjee, S (2004) A study on structure and properties of a hot forged HSLA-80 steel. Transactions of the Indian Institute of Metals, 57 (1). pp. 25-33.

Das, Samar and Joarder, A (1997) Effect of long-term service exposure at elevated temperature on microstructural changes of 5Cr-0.5Mo steels. Metallurgical and Materials Transactions A, 28 (8). pp. 1607-1616.

Das, Suchandan K (2001) Evaluation of solid-liquid interface profile during continuous casting by a spline based formalism. Bulletin of Materials Science, 24 (4). pp. 373-378.

Das, Suchandan K (1997) Function space theory of dynamic nucleation during solidification at high cooling rates. Bulletin of Materials Science, 20 (5). pp. 643-650.

Das, Suchandan K (1993) Mathematical investigation of the flow profile sensitivity of the electromagnetic velocimeter for metallurgical fluid-flow measurements. Transactions of the Indian Institute of Metals, 46 (3). pp. 141-145.

Das, Suchandan K (1993) Mathematical-modeling of transport phenomena in electrolysers with internal electrolyte recirculation. Bulletin of Electrochemistry, 9 (8-10). pp. 526-529.

Das, Suchandan K (1993) Numerical formalism for solving heat-transfer in continuous-casting process by nonorthogonal coordinate transformation strategy. Scandinavian Journal Of Metallurgy, 22 (4). pp. 198-202.

Das, Suchandan K (1996) Numerical modelling of the free boundary problem in levitation melting under continuous casting conditions. Scandinavian Journal of Metallurgy, 25 (5). pp. 187-192.

Das, Suchandan K (1999) Quantum mechanistic isomorphism of transient nucleation during rapid solidification processes. Transactions of the Indian Institute of Metals, 52 (4). pp. 205-210.

Das, Suchandan K (1999) Simulation of free boundary problem in electromagnetic levitation melting of metals in cold crucibles. Transactions of the Indian Institute of Metals, 52 (4). pp. 197-203.

Das, Suchandan K (1999) Thermal modelling of DC continuous casting including submould boiling heat transfer. Applied Thermal Engineering, 19 (8). pp. 897-916.

Das, Suchandan K (2003) Transport phenomena and process modelling issues in mineral processing operations. Transactions Of The Indian Institute Of Metals , 56 (3). pp. 269-279.

Das, Suchandan K and Godiwalla, K M (2006) Heat transfer characterization in the mould of a high speed continuous steel slab caster. In: 18th National & 7th ISHMT-ASME Heat and Mass Transfer Conference, Jan, 2006, IIT Guwahati.

Das, Suchandan K and Godiwalla, K M and Mehrotra, S P and Chatterjee, Amit and Krishnan, S H and Choudhary, P C (2005) Mathematical modelling of volatile matter evolution during carbonisation in metallurgical coke ovens. High Temperature Materials And Processes , 24 (5). pp. 301-314.

Das, Suchandan K and Godiwalla, K M and Mehrotra, S P and Dey, P K (2006) Mathematical modelling of erosion behaviour of impacted fly ash particles on coal fired boiler components at elevated temperature. High Temperature Materials And Processes , 25 (5-6). pp. 323-335.

Das, Suchandan K and Hedge, Shubha S and Godiwalla, K M and Mehrotra, S P and Dey, P K (2008) A probabilistic model to characterize erosion-oxidation damage on boiler grade steel impacted by solid particle. Journal Of Tribology-Transactions Of The Asme , 130 (4). 041601.

Das, Suchandan K and Mondal, G K and Sau, D C and Bandopadhay, D (2013) A Phenomenological Mathematical Model to Predict the Bosh Silicon Transport Under the Influence of Liquid Hold-up in the Dripping Zone of an Operating Blast Furnace. In: Proceeding of the International Conference on Science and Technology of ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Das, Suchandan K and Sarkar , A (1996) Computational modelling of thermal transport phenomena in continuous casting process based on non-orthogonal control volume approach. Communications in Numerical Methods in Engineering, 12 (10). pp. 657-671.

Das, Swapan K and Chatterjee, S and Tarafder, S (2006) Tensile fracture behaviour of microstructurally engineered Cu bearing high strength low alloy steel. Materials Science and Technology, 22 (12). pp. 1409-1414.

Das, Swapan K and Ghosh, R N and Sondhi, S K (2012) Prediction of carbide free layer formation in Fe-Ni Cr austentic steel process heater tube. Corrosion Engineering, Science and Technology, 47 (2). pp. 121-124.

Das, Swapan K and Mitra, A and Daspoddar, P K (1996) Thermal analysis of hydrated calcium aluminates. Journal of Thermal Analysis, 47 (3). pp. 765-774.

Das, Swapan K and Singh, S R and Gunjan, M K (2006) Investigation on Failure of Drop Tank Suspension Rod of Mig-21 T-96 Aircraft. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Das, T K and Mitra, A and Mandal, S K and Roy, Rajat K and Banerji, Pallab and Panda, A K (2014) Parametric controls on giant magnetoimpedance (GMI) behaviour of CoFeSiBCr amorphous wires for prospective sensor applications. Sensors and Actuators A-Physical , 220 (IF-1.841). pp. 382-387.

Das, T K and Panda, A K and Mitra, A and Banerji, Pallab and Mandal, S K (2014) Rapidly solidified CoFeSiBCr amorphous wire : From manipulation to giant magnetoimpedance sensor applications. 195 Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 195-202.

Das, Tuhin and Ghosh Chowdhury, S (2012) Micro Structural Characterization of Tensile Deformed TWIP Steel. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Das, Tuhin and Saha, Rajib and Bera, Supriya and Dahmen, Kirsten and Ghosh, M and Haldar, A and Bleck, Wolfgang and Ghosh Chowdhury, S (2015) Effect of High Tensile Strain Rate on the Evolution of Microstructure in Fe-Mn-C-Al Twinning-Induced Plasticity (TWIP) Steel. Metallurgical and Materials Transactions A, 46A (1) (IF-1.730). pp. 6-11.

Dasgupta, P and Bhattacharjee, S (1993) Prediction of boiling point of halomethanes by atomic contribution method and their correlation with geometric volume. Chemical Engineering Science, 48 (8). pp. 1535-1538.

Datar, N S and Reddy, S C and Chattopadhyay, R and Guha, B K and Bhatnagar, S S (1974) Industrial scale trails on niobium treated high strength low alloy structural steel. NML Technical Journal, 16 (2). pp. 1-4.

Datta, A K (2014) Low cycle fatigue life prediction of thin stiffened plates under repetitive stresses. In: International conference on Fatigue Damage of Structural Materials X, September 21-26, 2014, Hyannis, USA.

Datta, A K (2014) Responses of stiffened plates with varying depth of stiffeners under uniform lateral loads. In: International conference on Fatigue Damage of Structural Materials X, September 21-26, 2014, Hyannis, USA.

Datta, A K and Das, Goutam and De, P K (2006) Finite element modelling of steel rolling process. Journal of Metallurgy and Materials Science, 48 (3). pp. 173-180.

Datta, A K and Das, Goutam and De, P K (2006) Steel production in India and its impact in construction - A review. Journal of Metallurgy and Materials Science, 48 (4). pp. 205-214.

Datta, A K and Das, Goutam and De, P K and Ramachandrarao, P and Mukhopadhyay, M (2006) Finite element modeling of rolling process and optimization of process parameter. Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing , 426 (1-2). pp. 11-20.

Datta, A K and Mandal, D and Sahoo, K L (2011) Measuring uncertainties of metal working processes in computational simulations : A novel approach. Journal of Metallurgy and Materials Science, 53 (2). pp. 183-187.

Datta, A K and Sivaprasad, S and Bar, H N and Halder, N and Prasad, P (2015) Estimation of available in-elastic dissipation energy of high tensile steels against earthquake excitations. Journal of Metallurgy and Materials Science, 57(4) . pp. 197-209.

Datta, A K and Sivaprasad, S and Prasad, P (2017) Free vibration analysis and shape optimization of offshore tubular structures. Journal of Metallurgy and Materials Science, 59(3) . pp. 133-141.

Datta, S and Deb, P and Bandyopadhyay, N R and Banerjee, M K (1998) Reinforcing age Hardenable Al-Cr Matrix Alloy In-Situ and by SiC/Al2O3. In: UNSPECIFIED.

De, J and Bhattacharjee, S and Dhar, S and Acharyya, S K and Gupta, S K and Tarafder, S (2014) Finite Element Simulation of Multi-Axial Low Cycle Fatigue of Material SA333. Procedia Engineering, 86 (NIF-0.629). pp. 158-165.

De, Santanu and Palit Sagar, S and Dey, Swapna and Prakash, Amit and Chattoraj, I (2010) Quantification of pitting in two tempers of 7075 aluminium alloy by non-destructive evaluation. Corrosion Science, 52 (5). pp. 1818-1823.

De, Subhabrata and Bhattacharya, J (2014) Dependence of bioremediation performance of acid mine drainage on substrate characteristics. Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 203-207.

Deb, Arnab and Sarma, Deepankar and Banerjee, M K (2005) Significance of logarithmic averaging of soil resistivity data for underground piplines using impressed current cathodic protection system. Journal of Metallurgy and Materials Science, 47 (3). pp. 169-176.

Debnath, P C and Banerjee, N G and Kar, B C (1963) Determination of Hydrogen in Metals and Alloys by carrier gas method. NML Technical Journal, 5 (3). pp. 25-27.

Deole, G S and Tambavekar, A S and Baviskar, V R and Sable, S R and Chitale, M M and Nimbalkar, V M (2014) Development of novel Al-alloy (Al-5Mg)/10Wt.%TiB 2 metal matrix composites by in-situ reaction synthesis. Journal of Metallurgy and Materials Science, 56(3) (NON-SCI). pp. 179-186.

Deole, G S and Tambavekar, A S and Baviskar, V R and Sable, S R and Chitale, M M and Nimbalkar, V M (2014) Wear behavior of Al-Alloy (Al-5Mg) in-situ reinforced TiB particulate. 217 Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 217-222.

Desai, P K (2001) Life Extension of Aircraft Components - An IAF Perspective. In: UNSPECIFIED.

Deshpande, Pravin P and Vagge, Shashikant T and More, Mahendra A and Kelkar, Sarika A (2011) Galvano static deposition of conducting poly (o-toluidine -co-o-anisidine) coating on low carbon steel and its corrosion performance. Journal of Metallurgy and Materials Science, 53 (3). pp. 269-274.

Dev, S C (1994) Roll - Claddim - A IC11-10D of Improving Properties of Materials. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Dev, S C and Basak, O and Mohanty, O N (1993) Development of cadmium-free silver metal-oxide contact materials. Journal of materials science, 28 (24). pp. 6540-6544.

Dev, S C and Basak, P and Dubey, R K (1985) Development of silver-silver cadmium composite for electrical contacts. NML Technical Journal, 27 (1-2). pp. 9-13.

Dev, S C and Basak, P and Mohanty, O N (1992) Cadmium-free silver composite contacts by roll-cladding. Transactions of the indian institute of metals, 45 (3). pp. 185-188.

Dev, S C and Basak, P and Singh, Inder and Dubey, R K (1992) A copper-base brazing alloy for electronics industries. Journal of Materials Science, 27 (24). pp. 6646-6652.

Dev, S C and Mohanty, O N (1994) Rapidly solidified low-silver brazing filler alloy foils. Journal of Materials Science, 29 (23). pp. 6329-6334.

Dev, S C and Singh, Inder and Basu, D K (1997) Corrosion behaviour of silver brazing alloys in different environments. Anti-corrosion methods and materials, 44 (4). 260- .

Devi, S and Bose, S K (1977) Quantitative estimation of elements and compounds by x-ray integrated intensity measurements. NML Technical Journal, 19 (2). pp. 39-43.

Dey, K C and Sharma, V and Goswami, B (2012) Polyoxometalates : From green compounds to smart materials. Journal of Metallurgy and Materials Science, 54(2) . pp. 119-124.

Dey, Ramendra Sundar and Hajra, Saumen and Sahu, Ranjan K and Raj, C Retna and Panigrahi, M K (2012) A rapid room temperature chemical route for the synthesis of graphene: metal-mediated reduction of graphene oxide. Chemical Communications, 48 (12). pp. 1787-1789.

Dey, Shobhana and Bhattacharjee, S (2003) Collectorless flotation of a coking coal. Transactions Of The Indian Institute Of Metals , 56 (5). pp. 477-482.

Dey, Shobhana and Bhattacharjee, S and Bhattacharyya, K K (1997) Collectorless flotation of coal with two-stage addition of pine oil. Minerals & metallurgical processing, 14 (4). pp. 13-16.

Dey, Shobhana and Bhattacharyya, K K (2007) Split and collectorless flotation to medium coking coal fines for multi-product zero waste concept. Fuel Processing Technology, 88 (6). pp. 585-590.

Dey, Shobhana and Pathak, P N (2005) Comparative studies of amenability to processing of Graphite from different sources. Transactions of the Indian Institute of Metals, 58 (5). pp. 905-910.

Dhara, S and Kumar, R R and Mallick, A and Chowdhury, G M and Roy, B C and Das, A and Das, T P and Singh, U K (2013) Water Surface Tension and it’s Effect on Sintering: A Practical Experience in Bokaro Steel Plant. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Dhayal, Ashok Kumar and Pramanick, A K (2011) Oxide Layer Formation on Al-Si-Zr Alloy using Anodizing process. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Digges, Thomas G (1958) Boron Steels. In: Symposium on Production, Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Digges, Thomas G (1961) Research on Light Metals in the Metallurgy Division, National Bureau of Standards. NML Technical Journal, 3 (1). pp. 22-28.

Director, NML (1961) Abstracts of Papers. NML Technical Journal, 3 (1). pp. 11-21.

Director, NML (1960) Abstracts of Papers. NML Technical Journal, 2 (1). pp. 2-10.

Director, NML (1962) Abstracts of Papers. NML Technical Journal, 4 (1). pp. 11-19.

Director, NML (1964) Abstracts of papers -- Symposium on Micro-Metallurgy - The Role of Minute Additions to Ferrous and Non-ferrous Metals and Alloys. NML Technical Journal, 7 (1). pp. 14-26.

Director, NML (1964) Abstracts of papers- Symposium on Utilization of Metallurgical Wastes. NML Technical Journal, 6 (1). pp. 18-29.

Director, NML (1963) Abstracts of papers-Symposium on iron and steelmaking. NML Technical Journal, 5 (1). pp. 14-23.

Director, NML (1954) Annual Report 1954. NML, Jamshedpur.

Director, NML (1961) Annual Report 1960-1961. NML, Jamshedpur.

Director, NML (1964) Annual Report 1963-1964. NML, Jamshedpur.

Director, NML (1967) Annual Report 1966-1967. NML, Jamshedpur.

Director, NML (1970) Annual Report 1969-1970. NML, Jamshedpur.

Director, NML (1974) Annual Report 1973-1974. NML, Jamshedpur.

Director, NML (1975) Annual Report 1974-1975. NML, Jamshedpur.

Director, NML (1976) Annual Report 1975-1976. NML, Jamshedpur.

Director, NML (1977) Annual Report 1976-1977. NML, Jamshedpur.

Director, NML (1978) Annual Report 1977-1978. NML, Jamshedpur.

Director, NML (1979) Annual Report 1978-1979. NML, Jamshedpur.

Director, NML (1980) Annual Report 1979-1980. NML, Jamshedpur.

Director, NML (1986) Annual Report 1985-1986. NML, Jamshedpur.

Director, NML (1987) Annual Report 1986-1987. NML, Jamshedpur.

Director, NML (1990) Annual Report 1987-1990. NML, Jamshedpur.

Director, NML (1991) Annual Report 1990-1991. NML, Jamshedpur.

Director, NML (1994) Annual Report 1993-1994. NML, Jamshedpur.

Director, NML (1995) Annual Report 1994-1995. NML, Jamshedpur.

Director, NML (1996) Annual Report 1995-1996. NML, Jamshedpur.

Director, NML (1997) Annual Report 1996-1997. NML, Jamshedpur.

Director, NML (1998) Annual Report 1997-1998. NML, Jamshedpur.

Director, NML (1999) Annual Report 1998-1999. NML, Jamshedpur.

Director, NML (2000) Annual Report 1999-2000. NML, Jamshedpur.

Director, NML (2004) Annual Report 2003-2004. NML, Jamshedpur. ISBN 0972-4273

Director, NML (2005) Annual Report 2004-2005. NML, Jamshedpur. ISBN 0972-4273

Director, NML (2006) Annual Report 2005-2006. NML, Jamshedpur. ISBN 0972-4273

Director, NML (2007) Annual Report 2006-2007. NML, Jamshedpur. ISBN 0972-4273

Director, NML (2008) Annual Report 2007-2008. NML, Jamshedpur. ISBN 0972-4273

Director, NML (2011) Annual Report 2010-2011. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2012) Annual Report 2011-2012. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2013) Annual Report 2012-2013. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2014) Annual Report 2013-2014. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2015) Annual Report 2014-2015. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2017) Annual Report 2016-2017. CSIR- National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2018) Annual Report 2017-2018. CSIR- National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2019) Annual Report 2018-2019. CSIR- National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (2020) Annual Report 2019-2020. CSIR-National Metallurgical Laboratory, Jamshedpur. ISBN 0972-4273

Director, NML (1968) Awards, Honours and Nominations. NML Technical Journal, 10 (3). pp. 33-37.

Director, NML (1971) Central creep testing facility at the National Metallurgical Laboratory. NML Technical Journal, 13 (2). pp. 37-41.

Director, NML (1968) Commercial Processes and Techniques developed at the National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 39-41.

Director, NML (1969) Creep Testing. NML Technical Journal, 11 (3). 3- .

Director, NML (2012) CSIR-NML Exhibition Materials. [Show/Exhibition]

Director, NML (1959) Demonstration of Patented Process at the National Metallurgical Laboratory. NML Technical Journal, 1 (3). pp. 7-8.

Director, NML (1962) Developments in Iron and Steel making. NML Technical Journal, 4 (3). 3- .

Director, NML (2011) Director's Desk - 60th RC Meeting of CSIR-NML. CSIR-National Metallurgy Laboratory, Jamshedpur.

Director, NML (2011) Director's Desk - 60th RC Meeting of CSIR-NML (Hindi Version). CSIR-National Metallurgy Laboratory, Jamshedpur.

Director, NML (2012) Director's Desk - 61st RC Meeting of CSIR-NML (English Version). CSIR -National Metallurgical Laboratory, Jamshedpur.

Director, NML (2012) Director's Desk - 62nd RC Meeting of CSIR-NML (English Version). CSIR-NML, Jamshedpur.

Director, NML (2014) Director's Desk - 65th RC Meeting of CSIR-NML (English Version). CSIR-NML, Jamshedpur.

Director, NML (2015) Director's Desk - 67th RC Meeting of CSIR-NML (English Version). CSIR-NML, Jamshedpur.

Director, NML (2017) Director's Desk - 70th RC Meeting of CSIR-NML (English Version). CSIR- National Metallurgical Laboratory, Jamshedpur.

Director, NML (2016) Director's Desk - Special RC Meeting of CSIR-NML (English Version). CSIR- National Metallurgical Laboratory, Jamshedpur.

Director, NML (2010) Director's Desk: 58th RC Meeting of CSIR-NML (English Version). NML, Jamshedpur.

Director, NML (2011) Director's Desk: 59th RC Meeting of CSIR-NML. National Metallurgy Laboratory, Jamshedpur, Jamshedpur.

Director, NML (2015) Fatigue and Fracture - A compilation of 100 research publications. Compilation of 100 research publications . pp. 1-948.

Director, NML (1962) Ferro Alloy Symposium. NML Technical Journal, 4 (1). 3- .

Director, NML (1967) Ferro Alloys. NML Technical Journal, 9 (4). 3- .

Director, NML (1961) Ferro-Alloy Industry in India. NML Technical Journal, 3 (3). 3- .

Director, NML (1962) Ferro-Alloy Industry in India. NML Technical Journal, 4 (2). 3- .

Director, NML (1961) Ferro-Alloy Industry in India-A Symposium. NML Technical Journal, 3 (3). 2- .

Director, NML (1966) Fighting Against Corrosion. NML Technical Journal, 8 (4). 3- .

Director, NML (1966) Fighting Against Corrosion. NML Technical Journal, 8 (4). 3- .

Director, NML (1967) Fluorspar. NML Technical Journal, 9 (3). 3- .

Director, NML (1966) Foreign Collaboration. NML Technical Jounal, 8 (3). 3- .

Director, NML (1969) Foreword. NML Technical Journal, 11 (4). 3- .

Director, NML (1959) India 1958 Exhibition. NML Technical Journal, 1 (2). 44- .

Director, NML (1965) Indian Metallurgists and the Present Emergency. NML Technical Journal, 7 (4). 3- .

Director, NML (1963) International Symposium on Iron and Steelmaking. NML Technical Journal, 5 (2). 3- .

Director, NML (2011) la vintage metallurgie : 60 years of marriage of science to industry. In: la vintage metallurgie. National Metallurgical Laboratory, Jamshedpur, pp. 1-416.

Director, NML (1960) Light Metal Industry in India. NML Technical Journal, 2 (3). 5- .

Director, NML (1960) Light Metal Industry in India. NML Technical Journal, 2 (2). 6- .

Director, NML (1961) Light Metal Industry in India. NML Technical Journal, 3 (2). 3- .

Director, NML (1961) Light Metal Symposium. NML Technical Journal, 3 (1). 3- .

Director, NML (1964) List of Delegates. NML Techincal Journal, 6 (1). pp. 60-66.

Director, NML (1962) List of Delegates Attending the Symposium on "Ferro Alloy Industry in India" from overseas and outside Jamshedpur. NML Technical Journal, 4 (1). pp. 51-55.

Director, NML (1961) List of Delegates Attending the Symposium on "Light Metal Industry in India" from overseas and Outside Jamshedpur. NML Technical Journal, 3 (1). pp. 73-76.

Director, NML (1966) List of Delegates attending the Symposium on Metallurgy of Substitute Ferrous and Non-ferrous Alloys. NML Technical Journal, 8 (1). pp. 81-84.

Director, NML (1965) List of Delegates Attending the symposium on Micro-metallurgy. NML Technical Journal, 7 (1). pp. 71-74.

Director, NML (1960) List of Delegates Attending the Symposium on Pilot Plants in Metallurgical Research and Development from Overseas and Outside Jamshedpur. NML Technical Journal, 2 (1). pp. 60-64.

Director, NML (1959) List of delegates to the symposium on Iron and Steel Industry in India from Overseas and Outside Jamshedpur. NML Technical Journal, 1 (1). pp. 121-127.

Director, NML (1998) List of NML Technical reports. National Metallurgical Laboratory, Jamshedpur.

Director, NML (1967) Manufacture of Special Ferro-Alloys-Process developed at the National Metallurgical Laboratory. NML Technical Journal, 9 (3). 30- .

Director, NML (1964) Metallurgical Wastes. NML Technical Journal, 6 (2). 5- .

Director, NML (1964) Micro-Metallurgy. NML Technical Journal, 6 (3). 5- .

Director, NML (1965) Micro-Metallurgy. NML Technical Journal, 7 (2). 3- .

Director, NML (1959) N.M.L. - a year in retrospect. NML Technical Journal, 1 (2). pp. 4-5.

Director, NML (1967) National Metallurgical Laboratory Foundry Stations. NML Technical Journal, 9 (4). 32- .

Director, NML (2010) NML Diamond Jubilee Souvenir. In: NML Diamond Jubilee Souvenir. National Metallurgy Laboratory, Jamshedpur.

Director, NML (2010) NML Technology Handbook. National Metallurgical Laboratory, Jamshedpur.

Director, NML (2010) NML: Glimpses of Life and Times. In: NML Diamond Jubilee Celebrations, Nov 26-27, 2010, NML Jamshedpur, India.

Director, NML (1962) Non-Ferrous Metal Industry in India. NML Technical Journal, 4 (4). 3- .

Director, NML (1963) Non-ferrous Metals and Substitute Alloys. NML Technical Journal, 5 (4). 3- .

Director, NML (1967) Non-ferrous metals technology. NML Technical Journal, 9 (2). 3- .

Director, NML (1959) Notes and news. NML Technical Journal, 1 (2). pp. 41-43.

Director, NML (1959) Notes and News. NML Technical Journal, 1 (3). pp. 37-42.

Director, NML (1959) Notes and news. NML Technical Journal, 1 (4). pp. 41-49.

Director, NML (1960) Notes and News. NML Technical Journal, 2 (2). pp. 32-42.

Director, NML (1960) Notes and News. NML Technical Journal, 2 (2). pp. 26-33.

Director, NML (1960) Notes and News. NML Technical Journal, 2 (4). pp. 27-32.

Director, NML (1961) Notes and News. NML Technical Journal, 3 (2). pp. 36-44.

Director, NML (1961) Notes and News. NML Technical Journal, 3 (3). pp. 32-37.

Director, NML (1961) Notes and News. NML Technical Journal, 3 (4). pp. 25-27.

Director, NML (1962) Notes and News. NML Technical Journal, 4 (2). pp. 39-42.

Director, NML (1962) Notes and News. NML Technical Journal, 4 (3). pp. 33-37.

Director, NML (1962) Notes and News. NML Technical Journal, 4 (4). pp. 31-34.

Director, NML (1963) Notes and News. NML Technical Journal, 5 (2). pp. 38-40.

Director, NML (1963) Notes and news. NML Technical Journal, 5 (3). pp. 32-35.

Director, NML (1963) Notes and News. NML Technical Journal, 5 (4). pp. 33-35.

Director, NML (1964) Notes and news. NML Technical Journal, 6 (2). pp. 39-41.

Director, NML (1964) Notes and news. NML Technical Journal, 6 (4). pp. 31-33.

Director, NML (1965) Notes and news. NML Technical Journal, 7 (2). pp. 25-27.

Director, NML (1965) Notes and News. NML Technical Journal, 7 (3). pp. 28-31.

Director, NML (1965) Notes and News. NML Technical Journal, 7 (4). pp. 20-22.

Director, NML (1967) Notes and News. NML Technical Journal, 9 (1). pp. 35-36.

Director, NML (1967) Notes and News. NML Technical Journal, 9 (2). pp. 35-37.

Director, NML (1959) Ourselves. NML Technical Journal, 1 (1). 3- .

Director, NML (1968) Patents of National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 47-51.

Director, NML (1960) Pilot Plant Symposium. NML Technical Journal, 2 (1). iii- .

Director, NML (1968) Pilot Plants at National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 53-62.

Director, NML (1960) Pilot Plants in Metallurgical Research and Development. NML Technical Journal, 2 (2). 3- .

Director, NML (1960) pogramme-Symposium on "Pilot Plants in Metallurgical Research and Development". NML Technical Journal, 2 (1). iv-x.

Director, NML (1967) Process Developed at the National Metallurgical Laboratory - Production of Graphite Crucibles(Carbon and Clay bonded) Indian Patent Nos.58869 & 62352. NML Technical Journal, 9 (4). 31- .

Director, NML (1968) Process developed at the National Metallurgical Laboratory - Flux for submerged Arc welding. National Metallurgical Laboratory, Jamshedpur. (Submitted)

Director, NML (1967) Process Developed at the National Metallurgical Laboratory : Modification of Aluminium Silicon Alloys-Indian Patent No.76415. NML Technical Journal, 9 (2). 34- .

Indian Patent Nos. 58869 & 62352 (1967) Process developed at the National Metallurgical Laboratory: Production of Graphite Crucibles (Carbon and Clay bonded) - India Patents No. 58869 & 62352. Indian Patent Nos. 58869 & 62352.

Director, NML (1968) Processes developed at the National Metallurgical Laboratory for Commercial Exploitation. National Metallurgical Laboratory, Jamshedpur.

Director, NML (1968) Processes developed at the National Metallurgical Laboratory for Commercial Exploitation. NML Technical Journal, 10 (2). pp. 4-6.

Director, NML (1969) Profile of Prof. V.A. Altekar-Our New Director. NML Technical Journal, 11 (3). 4- .

Director, NML (1961) Programme-Symposium on "Light Metal Industry in India". NML Technical Journal, 3 (1). pp. 4-10.

Director, NML (1965) Programme-Symposium on Micro-Metallurgy-The Role of Minute Additions to Ferrous and Non-Ferrous Metals and Alloys. NML Technical Journal, 7 (1). pp. 6-13.

Director, NML (1963) Programme-Symposium on Recent Developments in Iron and Steelmaking with Special Reference to Indian Conditions. NML Technical Journal, 5 (1). pp. 4-12.

Director, NML (1964) Programme-Symposium on Utilization of Metallurgical Wastes. NML Technical Journal, 6 (1). pp. 8-17.

Director, NML (1968) Publications of National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 81-82.

Director, NML (1959) Recent Developments. NML Technical Journal, 1 (2). pp. 45-47.

Director, NML (1959) Recent Developments. NML Technical Journal, 1 (3). pp. 46-54.

Director, NML (1959) Recent Developments. NML Technical Journal, 1 (4). pp. 51-62.

Director, NML (1960) Recent Developments. NML Technical Journal, 2 (2). pp. 43-52.

Director, NML (1960) Recent Developments. NML Technical Journal, 4 (2). pp. 33-37.

Director, NML (1961) Recent Developments. NML Technical Journal, 3 (2). pp. 45-54.

Director, NML (1961) Recent Developments. NML Technical Journal, 3 (3). pp. 38-41.

Director, NML (1961) Recent Developments. NML Technical Journal, 3 (4). pp. 28-31.

Director, NML (1962) Recent Developments. NML Technical Journal, 4 (2). pp. 43-44.

Director, NML (1962) Recent Developments. NML Technical Journal, 4 (3). pp. 38-40.

Director, NML (1962) Recent Developments. NML Technical Journal, 4 (4). pp. 35-40.

Director, NML (1963) Recent Developments. NML Technical Journal, 5 (2). pp. 41-43.

Director, NML (1963) Recent Developments. NML Technical Journal, 5 (3). pp. 36-39.

Director, NML (1963) Recent Developments. NML Technical Journal, 5 (4). pp. 36-39.

Director, NML (1964) Recent Developments. NML Technical Journal, 6 (2). pp. 42-45.

Director, NML (1964) Recent Developments. NML Technical Journal, 6 (3). pp. 25-26.

Director, NML (1964) Recent Developments. NML Technical Journal, 6 (4). pp. 34-35.

Director, NML (1965) Recent Developments. NML Technical Journal, 7 (3). pp. 32-33.

Director, NML (1967) Research for Industry. NML Technical Journal, 9 (1). 3- .

Director, NML (1964) Research in Standardization. NML Technical Journal, 6 (4). 3- .

Director, NML (1961) Science's Return from Technology. NML Technical Journal, 3 (4). 3- .

Director, NML (1959) Scope of Pilot Plants. NML Technical Journal, 1 (3). 3- .

Director, NML (1970) The SCRATA Process for the Fumeless Decarburization of Steel by Oxide Injection. NML Technical Journal, 12 (4). 114- .

Director, NML (1968) The Set up of the National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 21-32.

Director, NML (1968) Silver Jubilee of Council of Scientific and Industrial Research. NML Technical Journal, 10 (3). 3- .

Director, NML (1968) Some Important Projects of National Metallurgical Laboratory. NML Technical Journal, 10 (3). pp. 79-80.

Director, NML (1968) Some Major Technical Consultancy Provided in Recent Years. NML Technical Journal, 10 (3). pp. 43-46.

Director, NML (1968) Special Equipment Available at National Metallurgical Laboratory for Research and Service Facilities. NML Technical Journal, 10 (3). pp. 63-78.

Director, NML (1959) Statistics. NML Technical Journal, 1 (2). 48- .

Director, NML (1959) Statistics. NML Technical Journal, 1 (3). pp. 55-59.

Director, NML (1959) Statistics. NML Technical Jounal, 1 (4). pp. 63-67.

Director, NML (1960) Statistics. NML Technical Journal, 2 (3). pp. 42-45.

Director, NML (1960) Statistics. NML Technical Journal, 2 (4). pp. 38-40.

Director, NML (1961) Statistics. NML Technical Journal, 3 (2). pp. 55-56.

Director, NML (1961) Statistics. NML Technical Journal, 3 (3). 42- .

Director, NML (1961) Statistics. NML Technical Journal, 4 (3). pp. 32-33.

Director, NML (1962) Statistics. NML Technical Journal, 4 (2). pp. 45-46.

Director, NML (1962) Statistics. NML Technical Journal, 4 (3). pp. 41-43.

Director, NML (1963) Statistics. NML Technical Journal, 5 (3). 40- .

Director, NML (1963) Statistics. NML Technical Journal, 5 (4). 40- .

Director, NML (1964) Statistics. NML Technical Journal, 6 (3). 27- .

Director, NML (1964) Statistics. NML Technical Journal, 6 (4). 36- .

Director, NML (1965) Statistics. NML Technical Journal, 7 (2). 28- .

Director, NML (1965) Statistics. NML Technical Journal, 7 (4). 23- .

Director, NML (1967) Statistics. NML Technical Journal, 9 (1). 37- .

Director, NML (1967) Statistics. NML Technical Journal, 9 (2). 38- .

Director, NML (1970) Studies on the Precipitation of AIN in Mild Steel. NML Technical Journal, 12 (1). pp. 29-31.

Director, NML (1965) Substitute Alloys. NML Technical Journal, 7 (2). 3- .

Director, NML (1966) Substitute Alloys. NML Technical Journal, 8 (2). 3- .

Director, NML (1963) Symposium on Iron and Steelmaking. NML Technical Journal, 5 (1). 3- .

Director, NML (1961) Symposium on Light Metal Industry in India. NML Technical Journal, 3 (2). pp. 4-6.

Director, NML (1964) Symposium on Metallurgical Wastes. NML Technical Journal, 6 (1). 7- .

Director, NML (1965) Symposium on Micro-Metallurgy. NML Technical Journal, 7 (1). 5- .

Director, NML (1960) Symposium on Pilot Plants in Metallurgical Research and Development-A Review. NML Technical Journal, 2 (2). pp. 4-7.

Director, NML (1994) Tailoring of Properties through Mechanical Processing. In: Tailoring of Properties through Mechanical Processing. NML, Jamshedpur, Jamshedpur.

Director, NML (1959) Technical aid to Industry. NML Technical Journal, 1 (2). pp. 6-7.

Director, NML (1960) Third five year plan. NML Technical Journal, 2 (4). 5- .

Director, NML (1959) Training in Research. NML Technical Journal, 1 (4). 3- .

Director, NML (1963) Utilisation of Metallurgical Wastes. NML Technical Journal, 5 (3). 3- .

Director, NML (1963) Utilisation of Metallurgical Wastes-A Symposium. NML Technical Journal, 5 (3). 4- .

Director, NML (1968) Utilization of Indigenous Technology. NML Technical Journal, 10 (1). 3- .

Director, NML (1969) Utilization of Low-grade Copper Ores. NML Technical Journal, 11 (2). 3- .

Director, NML (1966) Welcome to the Delegates. NML Technical Journal, 8 (1). 3- .

Director , NML (1959) Pilot Plants in Metallurgical Research and Development. NML Technical Journal, 1 (3). 5- .

Director , NML (1960) Recent Developments. NML Technical Journal, 2 (3). pp. 34-41.

Director , NML (1959) Symposium on "Iron and Steel Industry in India"-a review. NML Technical Journal, 1 (2). pp. 8-10.

Divya, M and Das, C R and Albert, S K and Goyal, Sunil and Ganesh, P and Kaul, R and Swaminathan, J and Murty, B S and Kukreja, L M and Bhaduri, A K (2014) Influence of welding process on Type IV cracking behavior of P91 steel. Materials Science and Engineering A, 613 (IF-2.409). pp. 148-158.

Divya, Nangunoori and Devender, V (2017) Mechanical behaviour of banana flax fiber reinforced soy resin composites. Journal of Metallurgy and Materials Science, 59(3) . pp. 111-116.

Dogan, Ali (1991) A Dynamical Model of Internal Friction in Formation of Martensite. NML Technical Journal, 33 (3-4). pp. 18-23.

Dogan , Ali (1992) Internal Friction and Its Relation with the Martensitic Transformation in In-TI Alloy. NML Technical Journal, 34 (1-2). pp. 3-7.

Dogan , Ali (1994) A Phase Stability Model for Martensite Transformation. NML Technical Journal, 36 (2). pp. 39-45.

Dubey, K S and Ramachandrarao, P and Lee, S (1996) Thermodynamic and viscous behaviour of undercooled liquids. Thermochimica Acta, 280-281 . pp. 25-62.

Dubey, R K (1963) Observations on oxygen melting of stainless steel. NML Technical Journal, 5 (3). pp. 10-17.

Dubey, R K and Chakraborty, S P and Gupte, P K (1968) Effect of bainite on mechanical properties of nickel-chromium constructional alloy steels. NML Technical Journal, 10 (1). pp. 4-9.

Dubey, R K and Chakravarty, S P and Gupte, P K (1969) Tempering of Die-steels based on indigenous materials. NML Technical Journal, 11 (3). pp. 26-29.

Dubey, R K and Gupte, P K (1969) Observations on continuous cooling transformation characteristics of alloy steels. NML Technical Journal, 11 (3). pp. 5-12.

Dubey, R K and Nag, P S and Gupte, P K (1968) Some observations on bainitic hardening of 18-4-1 high speed steel. NML Technical Journal, 10 (2). pp. 19-23.

Dunstone, Dick (2013) Coal Processing – Impact on Coke Quality. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Dutta, Anupama and Sivaprasad, S (2012) Study of Mechanical Behaviour of Materials. Training Report (TR). CSIR -NML, Jamshedpur. (Submitted)

Dutta, B M and Gupta, K N and Kapoor, A N (1967) Study of kinetics of hydrogen reduction of iron ores by electrical conductivity method. NML Technical Journal, 9 (1). pp. 23-28.

Dutta, S and Das, Arpan and Barat, K and Roy, Himadri (2012) Automatic characterization of fracture surfaces of AISI 304LN stainless steel using image texture analysis. Measurement: Journal of the International Measurement Confederation, 45 (5). pp. 1140-1150.

Dutta, Samik and Barat, K and Das, Arpan and Das, Swapan K and Shukla, A K and Roy, Himadri (2014) Characterization of micrographs and fractographs of Cu-strengthened HSLA steel using image texture analysis. Measurement, 47 (IF-1.526). pp. 130-144.

Dwivedi, Deepak and Singh, C B (2013) Reduction Kinetics of Iron Ore Pellets with Coal and Coal Dust. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, Jamshedpur.

E

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) Decreased chromia growth during isothermal and cyclic oxidation tests at 700ºC. Journal of Metallurgy and Materials Science, 53 (2). pp. 211-215.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2010) The effect of chromia scale thickness on ASR of solid oxide fuel cell interconnects at presence of Mn3O4 and MnFe2O4 spinels. Journal of Metallurgy and Materials Science, 52 (1). pp. 103-107.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2010) Evaluation of electrical conductivity activation energy of manganese coated Fe-17%Cr ferritic stainless steel. Journal of Metallurgy and Materials Science, 52 (3). pp. 273-278.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) Improved oxidation resistance of coated interconnects at 700ºC. Journal of Metallurgy and Materials Science, 53 (1). pp. 97-102.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) The influence of Mn spinel coatings on electrical conductivity of Fe-17%Cr alloy. Journal of Metallurgy and Materials Science, 53 (3). pp. 311-317.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) The influence of MnCo2O4, CoCr2O4, CoFe2O4 and Co3O4 spinels on the thickness of chromia scale during two types of oxidation tests. Journal of Metallurgy and Materials Science, 53 (2). pp. 205-209.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) Investigation on parabolic rate constant in presence of MnCo2O4, CoCr2O4, CoFe2O4 and Co3O4 coatings at 700ºC. Journal of Metallurgy and Materials Science, 53 (3). pp. 305-309.

Ebrahimifar, Hadi and Zandrahimi, Morteza (2011) Reduced electrical resistance of interconnects presence of Mn3O4 and MnFe2O4. Journal of Metallurgy and Materials Science, 53 (1). pp. 103-108.

Ebrahimifar, Hadi and Zandrahimia, Morteza (2010) Coating of AISI 430 ferritic stainless steel used in SOFCs in a Co-base pack mixture. Journal of Metallurgy and Materials Science, 52 (2). pp. 155-160.

El-Amoush, Amjad Saleh (2012) Effect of hydrogen charging conditions on the hardness of tin brass heat exchanger tube. Journal of Metallurgy and Materials Science, 54(1) . pp. 53-62.

Esfahani, Hamid Reza and Mirsalehi, Seyyed Ehsan (2014) Investigation on microstructure and mechanical properties of friction stir welded lap joints between commercially pure copper and St37-2 mild steel. Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 231-238.

F

Faivre, R and Bigot, R (1958) Studies on the Kinetics of very Rapid Cooling in Different Quenching Liquids- Application to Some Alloys of Iron, Nickel and Carbon. In: Symposium on Production, Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Fashu, Simbarashe and Li, Jianguo and Dan, Hu Qiao (2011) Purification of an industrial aluminum alloy by melt stirring during Ohno continuous casting process. Journal of Metallurgy and Materials Science, 53 (1). pp. 55-65.

Firoz, R and Basantia, S K and Khutia, N and Bar, H N and Sivaprasad, S and Murthy, G V S (2020) Effect of microstructural constituents on mechanical properties and fracture toughness of Inconel 718 with anomalous deformation behavior at 650 degrees C. Journal of Alloys and Compounds, 845 (IF-4.650). p. 156276.

G

Gaddu, Vinay D and Dawson, A S (2008) Case studies of failures in thermal power plant boilers. In: UNSPECIFIED.

Ganguly, Amit and Gupta, K N and Aswath, H S (1983) Gas based DRI for India. Iron and Steel International, 56 (4). pp. 143-149.

Garai, Subhadra and Sinha, Arvind (2014) Biomimetic nanocomposites of carboxymethyl cellulose-hydroxyapatite: Novel three dimensional load bearing bone grafts. Colloids and Surfaces B Biointerfaces, 115 (IF-4.287). pp. 182-190.

Garai, Subhadra and Sinha, Arvind (2016) Three dimensional biphasic calcium phosphate nanocomposites for load bearing bioactive bone grafts. Materials Science and Engineering C, 59 (IF-4.164). pp. 375-383.

Gaur, B and Singh, A K and Rao , N J (1994) Corrosion of mild-steel in hypochlorite solution - an electrochemical and weight-loss study. Indian Journal of Chemical Technology, 1 (4). pp. 225-229.

Gaur, B and Singh, T B and Singh, D D N (1996) Beneficial role of chloride ions during pickling of steel in sulfuric acid. Corrosion, 52 (2). pp. 154-159.

Ghali, Saeed Nabil and Eissa, Mamdouh and Faramawy, Hoda El and Ahmed, Azza and Mattar, Taha and Mishreky, Michael (2013) Production and Application of Advanced High Nitrogen Steel. In: Proceeding of the international Conference on Science and Technology of Ironmaking and Steelmaking , December 16-18, 2013, CSIR-NML Jamshedpur.

Ghali, Venkata Subbarao and Mulaveesala, Ravibabu (2011) Recent Advances in Non-stationary Thermal Non-destructive Characterization. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Ghosh, Arindam and Das, Samar and Chatterjee, S (2005) Ultrahigh strength hot rotted microalloyed steel: microstructure and properties. Materials Science and Technology, 21 (3). pp. 325-333.

Ghosh, Arindam and Shukla, R and Das, S and Chatterjee, S (2006) The structure and properties of a thermo-mechanically processed low carbon high strength steel. Steel Research International , 77 (4). pp. 276-283.

Ghosh, Arpita and Sivaprasad, S and Bhattacharjee, A and Kar, S (2013) Microstructure-fracture toughness correlation in an aircraft structural component alloy Ti-5Al-5V-5Mo-3Cr. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 568 (IF-2.108). pp. 61-67.

Ghosh, B N and Das, N K (1994) Thermomechanical Processing for Tailoring Properties in Steels. In: Tailoring of properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Ghosh, Ishita and Das, Suchandan K and Chakraborty, N (2014) An artificial neural network model to characterize porosity defects during solidification of A356 aluminum alloy. Neural Computing and Applications, 25 (IF-1.763). pp. 653-662.

Ghosh, K C and Mukherjee, B C and Ganguly, N N and Yusuf, M and Choudhury, V N (1992) A rapid complexometric scheme for analysis of iron, aluminum, calcium and magnesium in slags. Talanta, 39 (6). pp. 675-679.

Ghosh, M and Bansal, Gourav and Chandan, A and Shah, Minal and Tripathy, S and Murugaiyan, Premkumar and Sahoo, Biraj and Mukherjee, K and Srivastava, V C and Ghosh Chowdhury, S (2017) Functionally Driven Steels: A Review. Steel Tech, 12(1) (NonSCI). pp. 13-36.

Ghosh, M and Das, Swapan K and Singh, S R (2006) Investigation of caving-in incident of MIG 21 aircraft. In: National Conference on Failure Analysis – 2006, 22-23 Dec, 2006, Hyderabad.

Ghosh, M and Husain, M M and Das, Goutam and Das, S K and Upadhyay, A K and Singh, S R and Parida, N (2011) Metallurgical Analysis:Flying Accident to Mig-27 ML TS - 579. Sponsored (SSP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Ghosh, M and Husain, M M and Kumar, K and Kailas, S V (2013) Friction Stir-Welded Dissimilar Aluminum Alloys: Microstructure, Mechanical Properties, and Physical State. Journal of Materials Engineering and Performance , 22(12) (IF-0.915). pp. 3890-3901.

Ghosh, M and Kar, Abhijit and Ghosh, R N and Ray, Ajoy K (2008) A comparative study on the ageing behaviour of solder alloy-cu joint assemly using lead free solder and Sn-Pb eutectic solder alloy. In: The 3rd Asian Thermal Spray Conference (ATSC 2008), 2008, Singapore.

Ghosh, M and Kumar, K and Kailas, S V and Ray, Ajoy K (2010) Optimization of friction stir welding parameters for dissimilar aluminum alloys. Materials & Design, 31 (6). pp. 3033-3037.

Ghosh, M and Pramanick, A K and Ghosh Chowdhury, S and Singh, S R (2006) Phase Transformation in Secondary Reaction Zone (SRZ) in Polycrystalline Gas Turbine Blade made of Ni base Superalloy. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh, M and Singh, S R and Das, S K (2007) Metallurgical Analysis of the Damaged Wheel Hubs of AVRO HS-748 H-1517. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh, M and Singh, S R and Das, Swapan K (2007) Failure Investigation of Nose Jack Mounting Bracket of AVRO Aircraft H-1517. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh, M K (1978) Applications of solution technique using synthetic standards in spectrochemical analysis. NML Technical Journal, 20 (1-2). pp. 6-14.

Ghosh, M K (1970) Spectrographic analysis of low alloy steels by solution technique. NML Technical Journal, 12 (3). pp. 74-77.

Ghosh, M K and Gopalakrishna, S V (1970) Method of Spectrographic Analysis of Aluminium and Aluminium Alloys by Using Synthetic Standards. NML Technical Journal, 12 (2). pp. 61-64.

Ghosh, M K and Gopalkrishna, S V and Chakrabarti, H K (1975) Spectrochemical analysis of residual impurities in ferrro-chrome by solution-spark technique. Metallurgy & Metallurgical Engineering, 42 (12). p. 410.

Ghosh, M K and Gopalkrishna, S V and Chakrabarti, H K (1971) Spectrographic method of determination of niobium in steel. NML Technical Journal, 13 (4). pp. 100-103.

Ghosh, R N (1995) Basic Principles of Physical Metallurgy. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Ghosh, R N (1994) Modeling high-temperature creep of anisotropic material. Bulletin of Materials Science, 17 (7). pp. 1341-1350.

Ghosh, R N (2007) NDE Centre for Infrastructure Asset Management. Grant in Aid (GAP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh, R N (1994) Physical Metallurgy of Steel - Basic Principles. In: Workshop on Heat Treatment & Surface Engineering of Iron & Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Ghosh, R N (2001) Remaining Life Assessment of Engineering Components. In: UNSPECIFIED.

Ghosh, R N (1997) Structural and component integrity. In: UNSPECIFIED.

Ghosh, R N (2002) Superalloy: Processing and Performance. In: Proceedings of the Indo-Malaysian Joint Workshop (WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Ghosh, R N and Chaudhuri, S (1994) Creep strain prediction of 2-1/4-cr-1mo steel - a model-based approach. Bulletin of Materials Science, 17 (6). pp. 663-670.

Ghosh, R N and Chaudhuri, S and Roy, Nilima and Chattopadhyay, Lalitha (1995) Creep life extension of high-temperature components under wall thinning conditions. Sadhana-Academy Proceedings in Engineering Sciences, 20 ( ). pp. 331-339.

Ghosh, R N and Curtis, R V and MClean, M (1990) Creep deformation of single-crystal superalloys - modeling the crystallographic anisotropy. Acta Metallurgicaet Materiala, 38 (10). pp. 1977-1992.

Ghosh, R N and Das, S K and Mitra, A (2008) Damage assessment of process heater tube. In: UNSPECIFIED.

Ghosh, R N and Mclean, M (1992) High-temperature deformation in engineering alloys - modeling for strain or load control. Acta metallurgica et materialia, 40 (11). pp. 3075-3083.

Ghosh, R N and Mclean, M (1989) Modelling the orientation dependence of tertiary creep in single crystal superalloys. Scripta Metallurgica, 23 (8). pp. 1301-1306.

Ghosh, R N and Mitra, A (1983) Computer simulation of high temperature creep recovery and work hardening rate measurement techniques. Metal Science, 17 (12). pp. 590-600.

Ghosh, R N and Singh, R and Kumar, R (1985) An analysis of tertiary creep in Cr---1 Mo steel. Scripta Metallurgica, 19 (7). pp. 801-804.

Ghosh, R N and Singh, Raghubir and Kumar, Rajendra (1985) An analysis of tertiary creep in 2(1/4) Cr-1 Mo-steel. Scripta metallurgica, 19 (7). pp. 801-804.

Ghosh, Rita and Singh, D D N (2007) Kinetics, mechanism and characterisation of passive film formed on hot dip galvanized coating exposed in simulated concrete pore solution. Surface and Coatings Technology, 201 (16-17). pp. 7346-7359.

Ghosh, Rita and Singh, R J and Singh, D D N (2003) Comparing the corrosion resistance of thermo-mechanically treated rebars of low alloy and mild steels embedded in chloride-contaminated concrete mortars. Corrosion Prevention & Control , 50 (2). pp. 94-103.

Ghosh, Rita and Singh, R J and Singh, D D N (2003) Role of fluoride in accelerating corrosion and pitting of steel in concrete environments. Transactions Of The Indian Institute Of Metals , 56 (4). pp. 391-397.

Ghosh, S and Das, S K (1998) Carbide Morphology Observations in Rare-Earth-Treated Fe-Al-Si-C Alloys. Materials Characterization, 41 (5). pp. 217-221.

Ghosh, S and Prodhan, A and Mohanty, O N and Chakrabarti, A K (1996) A study on the oxidation characteristics of cast irons containing aluminum. Oxidation of Metals, 45 (1-2). pp. 109-131.

Ghosh, S and Sahu, Ranjan K and Raj, C Retna (2012) Pt-Pd alloy nanoparticle-decorated carbon nanotubes: a durable and methanol tolerant oxygen reduction electrocatalyst. Materials and Corrosion-Werkstoffe Und Korrosion, 23(38) .

Ghosh, Sabita and Das, Goutam (2012) Effect of pre strain on the indentation fracture toughness of high strength low alloy steel by means of continuum damage mechanics. Engineering Fracture Mechanics, 79 . pp. 126-137.

Ghosh, Sabita and Prakash, R V (2013) Study of Damage and Fracture Toughness due to Influence fo Creep and Fatigue of Commercially Pure Copper by Monotonic and Cyclic Indentation. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science , 44A(1) (IF-1.738). pp. 224-234.

Ghosh, Sabita and Sahay, S K and Das, Goutam (2004) Ball indentation technique - An important and useful method for studying the flow properties of materials. Transactions Of The Indian Institute Of Metals, 57 (1). pp. 51-60.

Ghosh, Sabita and Sahay, S K and Das, Goutam (2004) Effectiveness of ball indentation technique for evaluating mechanical properties of micro alloyed steel. Journal of Metallurgy and materials Science, 46 (2). pp. 95-105.

Ghosh, Sabita and Yadav, Sandip and Das, Goutam (2008) Ball Indentation Technique: A currently developed tool to study the effect of various heat treatments on the mechanical properties of En24 steel. Materials Letters, 62 (24). pp. 3966-3968.

Ghosh, Sabita and Yadav, Sandip and Das, Goutam (2008) Study of standard heat treatment on mechanical properties of Inconel 718 using ball indentation technique. Materials Letters, 62 (17-18). pp. 2619-2622.

Ghosh, Sourov and Sahu, Ranjan K and Raj, C Retna (2011) Shape-regulated high yield synthesis of electrocatalytically active branched Pt nanostructures for oxygen reduction and methanol oxidation reactions. Journal of Materials Chemistry, 21 (32). pp. 11973-11980.

Ghosh, Sukomal (1994) Heat Treatment of Cast Irons. In: Workshop on Heat Treatment & Surface Engineering of Iron & Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Ghosh, Sukomal (1995) Micro-Structural Characteristics of Cast Irons. In: Experimaental Techniques in Industrial Metallography [ETIM - 95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory (CSIR), Jamshedpur.

Ghosh, Sukomal and Kumar, A and Das, Swapan K and Das, Goutam and De, P K and Chakravarty, S (2006) Development of cast Al-Fe-V-Si alloys as a wear resistant and elevated temperature material for applications in engineering industries. Grant in Aid (GAP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh, Swati and Kain, V and Ray, A and Roy, H and Sivaprasad, S and Tarafder, S and Ray, K K (2009) Deterioration in Fracture Toughness of 304LN Austenitic Stainless Steel Due to Sensitization. Metallurgical and Materials Transactions A, 40 (12). pp. 2838-2949.

Ghosh , M and Husain, M M and Das, Goutam and Das, S K and Upadhyay, A K and Singh, S R and Parida, N (2011) Metallurgical Analysis : Ground Incident to MIG-27 ML TS-615. Other (TMP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Ghosh Chowdhury, S (2009) Physical Metallurgy. In: A Continuing Education Course on Metallurgy for Engineers, December 14-16, 2009, NML, Jamshedpur.

Ghosh Chowdhury, S and Das, Goutam and Das, Swapan K and Sivaprasad, S and Singh, S R and Ghosh, R N (2007) Failure Analysis of LP turbine free standing blade. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh Chowdhury, S and Das, Samar and Ravi Kumar, B and De, P K (2006) Twinning-induced sluggish evolution of texture during recrystallization in AISI 316L stainless steel after cold rolling. Metallurgical And Materials Transactions A-Physical Metallurgy And Materials, 37 A (8). pp. 2349-2359.

Ghosh Chowdhury, S and Das, Swapan K and Ravi Kumar, B and Kumar, S and Gottstein, G (2002) Textural development in AISI 316 stainless steel during cold rolling and annealing. Textures of Materials, 408-4 . pp. 1371-1376.

Ghosh Chowdhury, S and Gubicza, Jeno and Mahato, B and Chinh, Nguyen Q and Hegedus, Zoltan and Langdon, T G (2011) Texture evolution during room temperature ageing of silver processed by equal-channel angular pressing. Scripta Materialia, 64 (11). pp. 1007-1010.

Ghosh Chowdhury, S and Jena, A K and Ray, R K (2000) Recovery and ordering in cold-rolled boron-doped Ni76Al24. Metallurgical and Materials Transactions A, 31 (9). pp. 2127-2134.

Ghosh Chowdhury, S and Jena, A K and Ray, R K (1998) Recrystallization behavior of boron-doped Ni76Al24. Metallurgical and Materials Transactions A, 29 (12). pp. 2893-2902.

Ghosh Chowdhury, S and Kumar, P and Das, Arpan and Das, Swapan K and Mahato, B and De, P K (2008) Evolution of grain-boundary character distribution during iterative processing of an austenitic stainless steel. Philosophical Magazine Letters Online ISSN 1362-3036, 88 (6). pp. 407-414.

Ghosh Chowdhury, S and Mahato, B and Da silva, H R and Lourenco, G G and Santos, D B (2008) Evolution of texture in ultra-fine grained ferrite through warm-rolling and intercritical annealing. Nanomaterials By Severe Plastic Deformation Iv, Pts 1 And 2 Book Series: Materials Science Forum , 584-586 (1-2). pp. 610-616.

Ghosh Chowdhury, S and Minz, R K and Rajnikanth, V and Munda, Parikshit and Shah, Minal and Das, Swapan K and Sahoo, K L and Paul, K K (2015) Development of new silt erosion resistant steel for hydro turbine components. Iron & Steel Review, 59(6) .

Ghosh Chowdhury, S and Pereloma, Elena V and Santos, D B (2009) Corrigendum to “Evolution of texture at the initial stages of continuous annealing of cold rolled dual-phase steel: Effect of heating rate” [Mater. Sci. Eng.: A 480 (2008) 540–548]. Materials Science and Engineering: A , 525 (1-2). 211- .

Ghosh Chowdhury, S and Pereloma, Elena V and Santos, D B (2008) Evolution of texture at the initial stages of continuous annealing of cold rolled dual-phase steel: Effect of heating rate. Materials Science and Engineering A, 480 (1-2). pp. 540-548.

Ghosh Chowdhury, S and Ray, R K (2005) Violation of Schmid's law and tension-compression asymmetry in L1(2) structured alloys: role of ordered structure. Materials Science and Technology, 21 (2). pp. 211-217.

Ghosh Chowdhury, S and Sahu, Puspendu and Mahato, B and De, P K (2009) Evolution of Recrystallization Texture in AISI300 Series Austenitic Stainless Steels After Cold Rolling to Large Strain. Microstructure and Texture in Steels, 22 (22). pp. 361-378.

Ghosh Chowdhury, S and Singh, Raghuvir (2008) The influence of recrystallized structure and texture on the sensitization behaviour of a stable austenitic stainless steel (AISI 316L). Scripta Materialia, 58 (12). pp. 1102-1105.

Ghosh Chowdhury, S and Srivastava, V C and Das, Goutam and De, P K and Das, Swapan K and Swaminathan, J and Mandhyan, Ajay and Singh, S R (2006) Development of High Temperature conductors for Power Transmission Lines. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Ghosh Chowdhury, S and Xu, Cheng and Langdon, T G (2008) Texture evolution in an aluminum alloy processed by ECAP with concurrent precipitate fragmentation. Materials Science and Engineering: A, 473 (1-2). pp. 219-225.

Godiwalla, K M and Das, Suchandan K and Sivaramakrishnan, C S (1999) Mathematical modelling of electromagnetic phenomenon in aluminium smelting cells. Transactions of the Indian Institute of Metals, 52 (2-3). pp. 103-108.

Godiwalla, K M and Roy, Nilima and Chaudhuri, S and Ray, Ashok K (2001) Investigation and modeling of mechanical properties for thermal barrier coatings under bending. International Journal of Turbo & Jet-Engines, 18 (2). pp. 77-103.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1992) Fluid-flow in twin strand tundish water model. Transactions of the indian institute of metals, 45 (4). pp. 247-251.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1994) Simulation of fluid-flow phenomena in continuous-casting multistrand tundish through water modeling. Transactions of the indian institute of metals, 47 (5). pp. 333-337.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1995) Simulation of pneumatically agitated metallurgical vessels through water modelling. Scandinavian Journal Of Metallurgy, 24 (2). pp. 81-85.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1994) Statistical analysis of residence time distribution of fluid elements in continuous casting water model tundish with one side entry. 77th steelmaking conference, 77 ( ). pp. 703-712.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1993) Thermal stratification phenomena in a 4-strand cc tundish during teeming of steel water model study. ISIJ International, 33 (4). pp. 519-521.

Godiwalla, K M and Sinha, S K and Sivaramakrishnan, C S (1994) Water model simulation of tundish flow under varying conditions. Steel Research, 65 (7). pp. 267-272.

Gomes, Leandra Saviola (2013) Synthesis of Biomimetic Ferrofluid with Apoferritin as a MRI Contrast Agent. Masters thesis, VIT University, Vellore-623014.

Gopalakrishna, K and Sivaprasad, S and Venkateswarlu, K and Hari Kumar, K C (2012) Microstructural evolution and aging behavior of cryorolled Al-4Zn-2Mg alloy. Materials Science and Engineering A, 535 (IF-2.003). pp. 129-135.

Gopinath, K and Gupta, R K and Sahu, J K and Ray, P K and Ghosh, R N (2015) Designing P92 grade martensitic steel header pipes against creep–fatigue interaction loading condition: Damage micromechanisms. Materials & Design, 86 (IF-3.501). pp. 411-420.

Gorai, Bipra and Jana, R K and Khan, Z H (2002) Electrorefining electrolyte from copper plant dust. Materials Transactions, 43 (3). pp. 532-536.

Gorai, Bipra and Jana, R K and Premchand, (2003) Characteristics and utilisation of copper slag - a review. Resources Conservation and Recycling, 39 (4). pp. 299-313.

Goswami, B and Kumar, S B and Ray, Ashok K (2011) Perspectives of developments in nickel based allied systems. Journal of Metallurgy and Materials Science, 53 (3). pp. 233-252.

Goswami, B and Raj, A and Singh, M P and Ray, Ashok K (2013) Mechanical properties and ferrite formation in microalloyed steel. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 1-19.

Goswami, B and Raj, A and Srivastava, S C and Ray, Ashok K (2014) Vanadium in industrial traditions and innovations. Journal of Metallurgy and Materials Science, 56(3) (NON-SCI). pp. 149-161.

Goswami, B and Ravi Kumar, B and Tarafder, S and Guguloth, K and Rupa, P K P and Kumar, S B and Ray, Ashok K (2007) Fatigue damage of a thermal barrier coated Ni-base superalloy. High Temperature Materials and Processes, 26 (3). pp. 209-219.

Goswami, B and Ray, Ashok K (2010) Emerging trends in alternative processing and weather effects of Al-Li-X alloys. Journal of Metallurgy and Materials Science, 52 (3). pp. 187-208.

Goswami, B and Ray, Ashok K (2010) Emerging trends in joining processes of Al-Li-X alloys. Journal of Metallurgy and Materials Science, 52 (2). pp. 109-128.

Goswami, B and Ray, Ashok K (2011) Emerging trends in plasticity and precipitation of Al-Li-X alloys. Journal of Metallurgy and Materials Science, 53 (1). pp. 1-23.

Goswami, B and Ray, Ashok K (2011) Emerging trends of alloy and composite formation in Al-Li-X alloys. Journal of Metallurgy and Materials Science, 53 (2). pp. 109-131.

Goswami, B and Ray, Ashok K (2011) Perspectives of innovations in superalloys for gas turbines. Journal of Metallurgy and Materials Science, 53 (4). pp. 325-347.

Goswami, B and Ray, Ashok K (2008) Perspectives of nanocrystalline materials and metallic glass in pure nickel and nickel base alloys. Journal of Metallurgy and Materials Science, 50 (4). pp. 195-217.

Goswami, B and Ray, Ashok K (2009) Perspectives of sensor alloys in nickel base systems. Journal of Metallurgy and Materials Science, 51 (1). pp. 1-20.

Goswami, B and Ray, Ashok K (2009) Perspectives of shape memory surgical alloys in nickel base systems. Journal of Metallurgy and Materials Science, 51 (2). pp. 77-89.

Goswami, B and Ray, Ashok K (2009) Recent bio-medical alloys in cobalt base systems. Journal of Metallurgy and Materials Science, 51 (4-5). pp. 233-246.

Goswami, B and Ray, Ashok K (2007) Studies on certain aspect of superconductivity with reference to high Tc superconductors. Journal of Metallurgy and Materials Science, 49 (4). pp. 183-213.

Goswami, B and Ray, Ashok K and Raj, A (2015) Frontiers in materials and processing in chemical plants. Journal of Metallurgy and Materials Science, 57(2) . pp. 57-65.

Goswami, B and Ray, Ashok K and Raj, A (2015) Frontiers in materials for air frame structure. Journal of Metallurgy and Materials Science, 57(4) . pp. 187-195.

Goswami, B and Ray, Ashok K and Raj, A (2015) Frontiers in materials for fastening and joining. Journal of Metallurgy and Materials Science, 57(3) . pp. 115-126.

Goswami, B and Ray, Ashok K and Sahay, S K (2004) Thermal barrier coating system for gas turbine application - A review. High Temperature Materials And Processes, 23 (2). pp. 73-92.

Goswami, B and Sahay, S K and Ray, Ajoy K (2004) Application of thermal barrier coatings on combustion chamber liners - A review. High Temperature Materials And Processes , 23 (3). pp. 211-236.

Goswami, B and Sahay, S K and Ray, Ashok K (2008) Application of thermal barrier coating in light weight gas turbine. Journal of Metallurgy and Materials Science, 50 (1). pp. 1-21.

Goswami, J and Ghosh, S B and Chatterjea, A B and Altekar, V A (1972) Some observations on the production of iron powder by atomization. NML Technical Journal, 14 (3). pp. 94-101.

Goswami, M C (1997) Interrelation between kinetics of reduction and volume change during formation of directly reduced iron rod. Steel Research, 68 (12). pp. 507-511.

Goswami, M C and Biswas, P K and Vaish, A K (2001) Kinetics of reduction of low grade iron ore by charcoal. Journal of Metallurgy and materials Science, 43 (3). pp. 181-188.

Goswami, M C and Pal, J (2002) Role of coke quality in improving blast furnace performance. Journal of Metallurgy and materials Science., 44 (2). pp. 91-102.

Goswami, M C and Prakash, S and Sarkar, B (1998) A reacting system cold-model foaming study simulating in-bath smelting. Scandinavian Journal Of Metallurgy, 27 (3). pp. 97-102.

Goswami, M C and Prakash, S and Sarkar, S B (1999) Kinetics of smelting reduction of fluxed composite iron ore pellets. Steel Research, 70 (2). pp. 41-46.

Gourishanker, S (2001) Recent Techniques for Life Assessment of Boiler Components. In: UNSPECIFIED.

Govind, and Nair, K S and Mittal, M C and Lal, Kishori and Mahanti, R K and Sivaramakrishnan, C S (2001) Development of rapidly solidified (RS) magnesium–aluminium–zinc alloy. Materials Science and Engineering A, 304-306 . pp. 520-523.

Guguloth, K (2007) Application of stress-relaxation testing method for evaluation of creep properties and remaining life asse-ssment of high temperature alloys. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Guguloth, K and Ghosh, M and Swaminathan, J and Mitra, R (2020) Tensile creep and rupture behavior along with evolution of microstructure in a Zr-2.5Nb alloy. Materials Science and Engineering A, 791 . p. 139681.

Guguloth, K and Mitra, Rahul and Ghosh Chowdhury, S and Swaminathan, J (2018) Mechanism of creep deformation with evolution of microstructure and texture of Zr-2.5Nb alloy. Materials Science and Engineering: A, 721 (IF-3.094). pp. 286-302.

Guguloth, K and Sivaprasad, S and Chakrabarti, D and Tarafder, S (2014) Low-cyclic fatigue behavior of modified 9Cr-1Mo steel at elevated temperature. Materials Science and Engineering A, 604 (IF-2.409). pp. 196-206.

Guguloth, K and Swaminathan, J and Bagui, Sumanta and Ray, Ashok K (2012) Remnant Life Assessment and Microstructural Studies on Service Exposed Primary Reformer Tubes of a Catalytic Converter of an Ammonia Plant. High Temperature Materials Proceedings, 31 . pp. 759-767.

Guguloth, K and Swaminathan, J and Ghosh, R N (2014) Creep life predicition of P91 Steel from stress relaxation tests. In: ECCC Creep & Fracture 2014, May 5-7, 2014, Rome, Italy.

Guha, Avijit and Nayar, S (2014) Low-Temperature Biomimetic Synthesis of beta-Tricalcium Phosphate by Altering pH. Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry, 44(6) (IF-0.518). pp. 789-792.

Guha, Avijit and Nayar, S and Thatoi, Hruayanath (2010) Microwave irradiation enhances kinetics of the biomimetic process of hydroxyapatite nanocomposites. Bioinspiration & Biomimetics, 5 (2). 024001.

Guha, Avijit and Singh, Sashi and Kumaresan, R and Nayar, S and Sinha, Arvind (2009) Mesenchymal cell response to nanosized biphasic calcium phosphate composites. Colloids and Surfaces B: Biointerfaces, 73 (1). pp. 146-151.

Guha, Avijit and Sinha, Arvind (2011) Surface Mineralization of Hydrogels Through Octacalcium Phosphate. International Journal of Applied Ceramic Technology , 8 (3). pp. 540-546.

Guha, B K and Kulkarni, M R and Bhatnagar, S S (1972) An investigation on the metallurgical characteristics of stainless steel safety razor blades. NML Technical Journal, 14 (3). pp. 105-107.

Guha, J P and Chakravarty, P (1967) An x-ray investigation on the formation of oxides of niobium. NML Technical Journal, 9 (4). pp. 15-17.

Gujral, Amandeep and Ravi Kumar, B (2012) Deformation Induced Martensitic Transformation of 304L Austenitic Stainless Steel. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Gupta, A K (1958) Oxygen in Foundry Steel-Making. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Gupta, G S (2013) Fluid Flow Behavior In The Lower Part Of A Blast Furnace. In: Proceeding of the International conference on science and technology of iron making and steel making , December 16-18, 2013, CSIR-NML Jamshedpur.

Gupta, J R and Kapoor, A N (1967) Melleabilisation characteristics of white cast iron containing copper under inert atmosphere. NML Technical Journal, 9 (2). pp. 26-31.

Gupta, K K and Bhattacharjee, S and Kar, S and Chakravarty, S and Thakur, P and Bhattacharyya, G and Srivastava, S C (2003) Mineral compositions of eight common spices. Communications in Soil Science and Plant Analysis, 34 (5-6). pp. 681-693.

Gupta, K K and Ghosh, Dolly and Bhagat, A N and Hait, Jhumki and Chakravarty, S and Ranganathan, S (1999) Determination of carbidic carbon in steels. Talanta, 49 (1). pp. 41-45.

Gupta, K K and Singhal, K M (1977) Heat resistant steels in steam turbine. NML Technical Journal, 19 (3-4). pp. 54-57.

Gupta, K N and Vaish, A K (1994) On the potentiality of production of low S&P hot metal by VRDR-SAF process. In: Workshop on Production of Liquid Iron Using Coal, Aug 24-25, 1994, RRL Bhubaneswar.

Gupta, Pallawi and Nayar, S (2013) A Spectroscopic Study of Ferrofluid and Colloidal Graphene. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Gupta, R C (2013) The utilisation of iron ore fines : Technical options and challenges. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 235-256.

Gupta, R D (1979) Super hard materials for erosion resistance-Status of indigenous development. NML Technical Journal, 21 (1-2). pp. 11-14.

Gupta, S K and Pandey, K N and Kumar, Rajneesh (2018) Artificial intelligence-based modelling and multi-objective optimization of friction stir welding of dissimilar AA5083-O and AA6063-T6 aluminium alloys. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 232(4) (IF-1.625). pp. 333-342.

Gupta, Siddhi and Greeshma, T and Basu, Bikramjit and Goswami, Sudipta and Sinha, Arvind (2013) Stiffness-and wettability-dependent myoblast cell compa-tibility of transparent poly(vinyl alcohol) hydrogels. Journal of Biomedical Materials Research Part B-Applied, 101B (IF-2.834). pp. 346-354.

Gupta, Siddhi and Pramanick, A K and Kailath, A J and Mishra, T and Guha, Avijit and Nayar, S and Sinha, Arvind (2009) Composition dependent structural modulations in transparent poly(vinyl alcohol) hydrogels. Colloids and Surfaces B: Biointerfaces, 74 (1). pp. 186-190.

Gupta, Siddhi and Sinha, Satish and Sinha, Arvind (2010) Composition dependent mechanical response of transparent poly(vinyl alcohol) hydrogels. Colloids and Surfaces B: Biointerfaces, 78 (1). pp. 115-119.

Gupta, Siddhi and Webster, T J and Sinha, Arvind (2020) Correction to: Evolution of PVA gels prepared without crosslinking agents as a cell adhesive surface. Gupta S, Webster TJ, Sinha A. J Mater Sci Mater Med. 2020 Jul 21;31(8):63. doi: 10.1007/s10856-020-06399-1. PMID: 32696134. Journal of Materials Science - Materials in Medicine, 31(8) (IF-2.489). p. 63.

Gupta, T K S P and Nasar, A and Shamsuddin, M and Ramachandrarao, P (1994) Thermodynamic investigations of liquid-Te-saturated CdTe—ZnTe solid solutions. Thermochimica Acta, 247 (2). pp. 415-429.

Gupte, P K (1977) Roundup on research in foundry and metal solidification at Indias National-Metallurgical-Laboratory. International cast metals journal, 2 (4). pp. 9-12.

Gupte, P K and Nijhawan, B R (1958) An Investigation into the Development of Prospective Indian Austenitic Stainless Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Guria, A and Mandal, G K and Hodgson, Peter and Beynon, John H and Ghosh Chowdhury, S (2015) Effect of Twinning on Microstructural Evolution During Dynamic Recrystallisation of Hot Deformed As-Cast Austenitic Stainless Steel. Metallurgical and Materials Transactions A, 46(10) . pp. 4423-4428.

Guria, Chandan and Varma, Mohan and Mehrotra, S P and Gupta, Santosh K (2006) Simultaneous optimization of the performance of flotation circuits and their simplification using the jumping gene adaptations of genetic algorithm-II: More complex problems. International Journal of Mineral Processing, 79 (3). pp. 149-166.

H

Haase, C and Ghosh Chowdhury, S and La, Barrales-Mora and Molodov, D A and Gottstein, G (2013) On the Relation of Microstructure and Texture Evolution in an Austenitic Fe-28Mn-0.28C TWIP Steel during Cold Rolling. Metallurgical and Materials Transactions A - Physical Metallurgy and Materials Science, 44A (IF-1.738). pp. 911-922.

Halder, S and Ram, S and Ramachandrarao, P and Banerjee, H D (1995) Synthesis of high-energy-density Pr2Fe14-xCoxB, x<=3, magnets for practical applications. Bulletin of Materials Science, 18 (8). pp. 963-974.

Hamada, A S and Sahu, Puspendu and Ghosh Chowdhury, S and Karjalainen, L P and Levoska, J and Oittinen, T (2008) Kinetics of the γ → ε Martensitic Transformation in Fine-Grained Fe-26Mn-0.14C Austenitic Steel. Metallurgical and Materials Transactions A, 39 (2). pp. 462-465.

Hansda, Soma and Ghosh Chowdhury, S (2013) Recrystallization of TWIP Steels and Study of X-Ray Diffraction Pattern. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Hao, X J and Yin, W and Strangwood, M and Peyton, A and Dickinson, S J and Morris, P F and Davis, C L (2011) Monitoring of Steel Microstructures using Electromagnetic Sensors. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Harmain, G A (2005) An investigation on single overload fatigue crack growth retardation, Part-2(Crack closure decomposition). Journal of Metallurgy and Materials Science, 47 (4). pp. 189-197.

Harmain, G A (2005) An investigation on single overload fatigue crack growth retardation, Part-I (Plasticity zone interactions). Journal of Metallurgy and Materials Science, 47 (3). pp. 129-140.

Harmain, G A (2005) A numerical investigation on constant amplitude loading. Journal of Metallurgy and Materials Science, 47 (2). pp. 103-117.

Hart , D H (1960) The Role of Pilot Plant Investigation in the Development of Updraught Sintering of Broken Hill Lead Concentrate. NML Technical Journal, 2 (1). pp. 52-59.

Hatami, Mahdi Kazemi and Barsoum, Zuheir (2010) Fatigue assessment of cruciform joints welded in different positions. Journal of Metallurgy and Materials Science, 52 (1). pp. 87-102.

Hauser, M and Wendler, M and Ghosh Chowdhury, S and Weiss, A and Mola, J (2015) Quantification of deformation induced alpha '-martensite in Fe-19Cr-3Mn-4Ni-0.15C-0.15N austenitic steel by in situ magnetic measurements. Materials Science and Technology, 31(12) (IF-1.909). pp. 1473-1478.

Haxhiaj, A and Rama, M and Krasniqi, N and Haxhiaj, E (2011) The management of the melting process of electrical furnaces in Drenas. Journal of Metallurgy and Materials Science, 53 (3). pp. 253-260.

Hazra, S K and Hazra, Snehanu (2013) Coke for iron making. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Hazra, Sujan and Saxen, Henrik and Sengupta, Bhaskar (2013) Application of a One-Dimensional Steady-State Model for Process Supervision in Blast Furnace. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Hegde, L and Prasad, S N (1998) Formability of Metal-Matrix Composite based on Aluminium Alloy 6061 - Reinforced with Silicon Carbide Particulars. In: UNSPECIFIED.

Henry, G and Plateau, J (1963) Some Observations on a Cr-Mn-N Stainless Steel. NML Technical Journal, 5 (2). pp. 25-32.

Herbert, M A and Das, Goutam and Maiti, R and Chakraborty, M and Mitra, R (2010) Tensile properties of cast and mushy state rolled Al-4.5Cu alloy and in situ Al4.5Cu-5TiB(2) composite. International Journal of Cast Metals Research, The, 23 (4). pp. 216-224.

Hinde, J (1958) The Welding of Special and Alloy Steels. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Hiteshkumar, Patel and Jyoti, Menghani (2012) Wear characteristics of unalloyed and alloyed LM25- Aluminium casting. Journal of Metallurgy and Materials Science, 54(2) . pp. 131-135.

Hoar, T P and Hines, J G (1958) The Stress-Corrosion Cracking of Austentic Stainless Steels in Aqueous Chloride Solution. In: Symposium on Production, Properties and Appications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Hoff, Dan and Sheikh, Lubna and Bhattacharya, S and Nayar, S and Webster, T J (2013) Comparison study of ferrofluid and powder iron oxide nanoparticle permeability across the blood-brain barrier. International Journal of Nanomedicine, 8(1) (IF-3.463). pp. 703-710.

Holmes, G M (1962) Some Aspects of the Sampling and Analysis of Ferro Alloys. NML Technical Journal, 4 (1). pp. 33-40.

Hore, S and Das, Suchandan K (2013) Mathematical Modelling of Microstructure Evolution During Hot Strip Rolling of Trip Steel Using A Multi-Scale Framework. In: Proceeding of the international Conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Hore, S and Ghosh, R N (2011) Computer simulation of the high temperature creep behaviour of Cr–Mo steels. Materials Science and Engineering A, 528 (19-20). pp. 6095-6102.

Humane, M M and Vaish, A K and Swaminathan, J and Ravi Kumar, B and De, P K and Peshwe, D R and Paretkar, R K (2006) Comparison of hot rolled textures in different grades of high formable steels. Steel Research International, 77 (6). pp. 445-449.

Hunani, S R and Lodhari, D R and Dutta, S K and Das, A K (2013) Enrichment of Low Grade Iron Ore by Jigging and Shaking Table. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Husain, M M and Ghosh, M and Sarkar, R and Pal, T K and Prabhu, N (2018) Conventional and in situ tensile test of friction stir welded steel – Optimization of processing parameters. Materialwiss. Werkstofftech, 49 (IF-0.393). pp. 991-1005.

Hussain, Raja Rizwan and Alhozaimy, Abdulrahman and Al-Negheimish, Abdulaziz and Singh, D D N (2014) Time-dependent variation of the electrochemical impedance for thermo-mechanically treated versus plain low alloy steel rebars in contact with simulated concrete pore solution. Construction and Building Materials, 73 (IF-2.265). pp. 283-288.

I

Imai, Y and Ishizaki, Tetsuro (1958) Influence of Nitrogen on the Low Temperature Brittleness of steel. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1958, NML, Jamshedpur.

Indulal, C R and Vaidyan, A V and Kumar, G Sajeev (2012) The ion exchange properties of nanosized cerium molybdo iodate and cerium phospho iodate. Journal of Metallurgy and Materials Science, 54(4) . pp. 299-302.

Ineson, E and Hoyle, G (1958) The Cast Structure of High-Speed Steel. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Ishihara, Yoshio (1958) Progress of Special Steel-Making Process in Japan. In: Symposium on Production, Properties, and Applications, of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

J

Jackson, A (1961) The Ajax Furnace and Process. NML Technical Journal, 3 (2). pp. 7-12.

Jacob, K T and Srikanth, S and Iyengar, G N K (1986) Phase relations and activities in the Co-Ni-O system at 1373 K. Bulletin of Materials Science, 8 (1). pp. 71-79.

Jacomet, P (1966) The recent developments of aluminium conductors in France in public distribution and industrial plants. NML Technical Journal, 8 (1). pp. 31-38.

Jadayil, Anu and Wisam, M (2011) Solidification time effects on surface and subsurface aluminum casting defects. Journal of Metallurgy and Materials Science,, 53 (1). pp. 41-54.

Jain, Jitendra and Soni, S L and Sharma, Dilip (2010) Determination of wear rate of steel in high pressure and temperature zone for prediction of balance life of autofretagged tubes. Journal of Metallurgy and Materials Science, 52 (2). pp. 181-187.

Jain, Udit (2013) Corex & Finex-New Developments in Utilization of Low Grade Raw Materials. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Jaleel, V A and Panda, P K and Kannan, T S (1998) Evaluation of Mechanical Properties of SiC Whisker Reinforced In-Situ Composites Prepared by Carbothermal Reduction of Silicate Minerals. In: UNSPECIFIED.

James, J and Rao, MS (1992) Rice-Husk-Ash Cement - A Review. Journal of Scientific & Industrial Research , 51 (5). pp. 383-393.

Jamesh, M and Sankara Narayanan, T S N and Chu, P K and Park, Song and Lee, Min Ho (2013) Effect of Surface Mechanical Attrition Treatment of Titanium Using Alumina Balls: Surface Roughness, Contact Angle and Apatite Forming Ability. Frontiers of Materials Science, 7(3) . pp. 285-294.

Jamesh, M and Satendra, Kumar and Sankara Narayanan, T S N (2012) Electrodeposition of hydroxyapatite coating on magnesium for biomedical applications. Journal of Coatings Technology and Research, 9 (4). pp. 495-502.

Jana, Arpita and Devi, P S and Mitra, A and Bandyopadhyay, N R (2013) Synthesis of blue emitting ZnO nanorods exhibiting room temperature ferromagnetism. Materials Chemistry and Physics, 139(2-3) (IF-2.072). pp. 431-436.

Jana, R K (1993) Leaching of sea nodules in acidic chloride-sulfide media. Transactions of the Institution of Mining and Metallurgy Section C-Mineral Processing and Extractive, 102 ( ). C191-C194.

Jana, R K and Akerkar, D D (1989) Studies of the metal-ammonia-carbon dioxide-water system in extraction metallurgy of polymetallic sea nodules. Hydrometallurgy, 22 (3). pp. 363-378.

Jana, R K and Singh, D D N and Roy, S K (1995) Alcohol-modified hydrochloric acid leaching of sea nodules. Hydrometallurgy, 38 (3). pp. 289-298.

Jana, R K and Singh, D D N and Roy, S K (1996) Direct electrowinning of valuable metals from sea nodules using aqueous chloride bath. Transactions of the indian institute of metals, 49 (6). pp. 761-767.

Jana, R K and Singh, D D N and Roy, S K (1993) Electrochlorination of sea nodules to recover copper, nickel and cobalt. Hydrometallurgy, 32 (1). pp. 21-38.

Jana, R K and Singh, D D N and Roy, S K (1993) Hydrochloric-acid leaching of sea nodules with methanol and ethanol addition. Materials Transactions JIM, 34 (7). pp. 593-598.

Jana, R K and Singh, D D N and Roy , S K (1994) Electrowinning of metals using buffered sodium-chloride electrolyte during electrochlorination of sea nodules. Hydrometallurgy, 36 (3). pp. 295-314.

Jana , R K and Murthy, D S R and Nayak, A K and Mahanty, M S and Tiwary, S K and Akerkar, D D (1990) Leaching of roast-reduced polymetallic sea nodules to optimize the recoveries of copper, nickel and cobalt. International Journal of Mineral Processing, 30 (1-2). pp. 127-141.

Javoronkov, V A (1962) The Development of Rolling Mills in the USSR. NML Technical Journal, 4 (3). pp. 22-32.

Jayabal, S and Natarajan, U (2010) Effect of fibre length and fibre content on the mechanical properties of coir fiber/polyester composites. Journal of Metallurgy and Materials Science, 52 (4). pp. 341-350.

Jayakumar, T and Kumar, Anish (2011) Nondestructive Evaluation of Microstructure and Stresses in Steels. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Jena, B K and Sahu, S C and Satpati, B and Sahu, Ranjan K and Behera, D and Mohanty, S (2011) A facile approach for morphosynthesis of Pd nanoelectrocatalysts. Chemical Communications, 47 (13). pp. 3796-3798.

Jennings, R F and Frankau, A M (1959) Blast Furnace Burden Preparation with Reference to High Ash Coke. NML Technical Journal, 1 (1). pp. 80-87.

Jha, B B and Ojha, S N and Misra, B K (2008) Residual life estimation of high temperature tubings based on oxide scale thickness measurement. In: UNSPECIFIED.

Jha, Manis K and Kumar, Vinay and Bagchi, D and Singh, R J (2007) Processing of rayon waste effluent for the recovery of zinc and separation of calcium using thiophosphinic extractant. Journal of Hazardous Materials, 145 (1-2). pp. 221-226.

Jha, Manis K and Kumar, Vinay and Maharaj, L and Singh, R J (2005) Extraction and separation of Zn and Ca from solution using thiophosphinic extractant. Journal of Metallurgy and Materials Science, 47 (2). pp. 71-83.

Jha, Manis K and Kumar, Vinay and Singh, R J (2002) Solvent extraction of zinc from chloride solutions. Solvent Extraction and Ion Exchange , 20 (3). pp. 389-405.

Jha, Manis K and Upadhyay, R R and Lee, Jae-chun and Kumar, Vinay (2008) Treatment of rayon waste effluent for the removal of Zn and Ca using Indion BSR resin. Desalination, 228 (1-3). pp. 97-107.

Jindal, Vikas and De, P K and Venkateswarlu, K (2006) Effect of Al3Sc precipitates on the work hardening behavior of aluminum–scandium alloys. Materials Letters, 60 (28). pp. 3373-3375.

Jindal, Vikas and Rupa, P K P and Mandal, G K and Srivastava, V C (2014) Effect of High-Temperature Severe Plastic Deformation on Microstructure and Mechanical Properties of IF Steel. Journal of Materials Engineering and Performance, 23(6) (IF-0.981). pp. 1954-1958.

Jindal, Vikas and Srivastava, V C (2008) Growth of intermetallic layer at roll bonded IF-steel/aluminum interface. Journal of Materials Processing Technology, 195 (1-3). pp. 88-93.

Jindal, Vikas and Srivastava, V C and Das, Arpan and Ghosh, R N (2006) Reactive diffusion in the roll bonded iron–aluminum system. Materials Letters, 60 (13-14). pp. 1758-1761.

Jindal, Vikas and Srivastava, V C and Mishra, Suman K and Das, Goutam and Ghosh, R N (2006) Study of Structural Evaluation and Mechanical properties of IF Steel and Aluminium sheets processed by ARB process. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Jindal, Vikas and Srivastava, V C and Uhlenwinkel, V (2009) On the role of liquid phase stability and GFA parameters. Journal of Non-Crystalline Solids, 355 (28-30). pp. 1552-1555.

Joarder, A (1994) On the bainite structure in Cr-Mo-V rotor steel. Steel Research, 65 (8). pp. 345-349.

Joarder, A (1995) Physical Metallurgy of Sheets. In: Experimental Techniques in Industrial Metallography [ETIM - 95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR, Jamshedpur.

Joarder, A and Sarma, D S (1992) Bainite morphologies in a 0.2 C-1.5 Mn steel. Steel Research , 63 (1). pp. 33-38.

Joarder, A and Sarma, D S (1993) Bainitic microstructures in a 0.2%C---1%Mo steel. Scripta Metallurgica et Materialia, 28 (4). pp. 517-522.

Joarder, Asok (1994) High Speed Steels. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Joni, B and Al-Samman, T and Ghosh Chowdhury, S and Csiszar, G and Ungar, T (2013) Dislocation densities and prevailing slip-sytem types determined by X-ray line profile analysis in a textured AZ31 magnesium alloy deformed at different temperatures. Journal Of Applied Crystallography, 46(1) (IF-3.343). pp. 55-62.

Joshi, R M and Thimmaiah, K S and Deshpande, R V and Maheshwari, M D (2011) Nondestructive Evaluation of Weld seam Failures in Tubes and Other Structures for Thermal, Wind and Nuclear Power Applications. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

K

Kadgaye, Chetan and Hasan, Sk Md and Patra, Sudipta and Ghosh, M and Nath, S K and Karmakar, Anish (2021) Role of Cerium on Transformation Kinetics and Mechanical Properties of Low Carbon Steels. Metallurgical and Materials Transactions A, Online . pp. 1-18.

Kailath, A J and Dutta, K and Alex, T C and Mitra, A (2011) Crystallization Study of Cu56Zr7Ti37 Metallic Glass by Electrical Resistivity Measurement. Journal of Materials Science and Technology, 27 (3). pp. 275-279.

Kailath, A J and Mandal, Soumen (2012) The effect of Sn addition on the crystallization and thermal stability of Cu–Zr–Ti metallic glasses. Journal of Alloys and Compounds, 537 . pp. 275-279.

Kailath, A J and Panda, A K and Minz, R K and Das, Goutam and Ghosh, M and Kumar, A and Giri, A K and Mahato, B (2006) Synthesis and characterisation of Copper based bulk amorphous/nanophase alloys as melt spun ribbons. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Kale, Girish Madhav and Srikanth, S (1999) Electrochemical determination of the activity of Na2O in the pyrochlore phase of the Sb2O4-NaSbO3 system. Journal of the American Ceramic Society, 82 (8). pp. 2161-2165.

Kale, Girish Madhav and Srikanth, S (2000) Electrochemical determination of the Gibbs Energy of formation of Na2Fe2O4 and Na3Fe5O9 employing Na-β-Al2O3 solid electrolyte. Journal of the American Ceramic Society, 83 (1). pp. 175-180.

Kalinkin, A M and Kumar, S and Gurevich , B I and Kalinkina, E V and Tyukavkina, V V (2014) Synthesis of geopolymer materials based on slags of nonferrous metallurgy with the use of mechanoactivation. Glass Physics and Chemistry, 40(1) (IF-0.532). pp. 26-30.

Kaloshkina, Sergey and Churyukanovaa, Margarita and Zadorozhnyia, Vladislav and Shchetinina, Igor and Roy, Rajat K (2011) Curie temperature behaviour at relaxation and nanocrystallization of Finemet alloys. Journal of Alloys and Compounds, 509 (Suppl 1). S400-S403.

Kalpana, Y and Roy, S and Alka, (2014) Evaluation of plant extracts as corrosion inhibitors for Cu-alloys in river water. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 59-66.

Kalpana, Y and Sushanta, Roy and Alka, (2015) Evaluation of silanes as corrosion resistant coatings for Cu-alloy in Sea water. Journal of Metallurgy and Materials Science, 57(1) . pp. 27-32.

Kalshetty, Shivanand and Basavaraja, S and Bedre, Mahesh D and Deshpande, Raghunandan and Venkataraman, A (2011) Synthesis and characterization of SnO2 by alginate template method. Journal of Metallurgy and Materials Science, 53 (2). pp. 175-181.

Kamaraj, A and Haldar, Nimai and Murugaiyan, Premkumar and Misra, S (2020) High-Temperature Simulation of Continuous Casting Mould Phenomena. Transactions of the Indian Institute of Metals, 73(8) (IF-1.205). pp. 2025-2031.

Kanari, N and Mishra, D and Mochon, J and Verdeja, L F and Diot, F and Allain, E (2010) Some kinetics aspects of chlorine-solids reactions. REVISTA DE METALURGIA, 46 (1). pp. 22-36.

Kante, Murali and Reddy, Rama Koti and Ghali, Venkata Subbarao and Mulaveesala, Ravibabu (2011) Frequency Modulated Infrared Imaging for Non-Destructive Testing of Steel Materials. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Kapur, A N (1962) Scientific Research and Industrial Development and Role of National Research Development Corporation. NML Techinical Journal, 4 (2). pp. 12-14.

Kar, Abhijit and Ghosh, M and Ghosh, R N and Majumdar, Bhaskar S and Ray, Ajoy K (2008) Evolution of mechanical and electrical properties of tin–lead and lead free solder to copper joint interface. Materials Letters, 62 (1). pp. 151-154.

Kar, Abhijit and Ghosh, M and Ghosh, R N and Ray, Ajoy K (2007) Comparative study of tin lead and lead free solder joint interface. In: 2 nd International Conference on Recent Advances in Composite Materials (ICRACM-2007), February, 20-23, 2007, New Delhi.

Kar, Abhijit and Ghosh, M and Majumdar, Bhaskar S and Ghosh, R N and Ray, Ajoy K (2007) Interfacial microstructure, shear strength and electrical conductivity of Sn-3 center dot 5Ag-o center dot 5In/Cu lead free soldered joints. Materials Technology, 32 (3). pp. 161-165.

Kar, Abhijit and Mandal, Sudipta and Ghosh, R N and Ghosh, T K and Ray, Ajoy K (2007) Role of Ti diffusion on the formation of phases in the Al2O3-Al2O3 brazed interface. Journal of Materials Science, 42 (14). pp. 5556-5561.

Kar, Abhijit and Mandal, Sudipta and Rathod, S and Ray, Ajoy K (2006) Effect of Ti diffusivity on the formation of phases in the interface of alumina-alumina brazed with 97(Ag40Cu)3Ti filler alloy. Brazing And Soldering, Proceedings . pp. 219-225.

Kar, Abhijit and Palit Sagar, S and Ray, Ajoy K (2007) Characterization of the ceramic–metal brazed interface using ultrasonic technique. Materials Letters, 61 (19-20). pp. 4169-4172.

Kar, Abhijit and Ray, Ajoy K (2007) Characterization of Al2O3–304 stainless steel braze joint interface. Materials Letters, 61 (14-15). pp. 2982-2985.

Kar, S and Maity, S and Chakravarty, S and Bhattacharyya, G and Dureja, V and Bhattacharjee, S (2002) Heavy metal distribution in some of the seasonal vegetables of Patamda, the agricultural nerve centre of East Singhbhum district in the state of Jharkhand. Journal of Metallurgy and materials Science., 44 (3). pp. 161-165.

Kar, Sujoy and Suman, Swati and Sivaprasad, S and Chaudhuri, Atanu and Bhattacharjee, A (2014) Processing-microstructure-yield strength correlation in a near β Ti alloy,Ti–5Al–5Mo–5V–3Cr. Materials Science and Engineering A, 610 (IF-2.409). pp. 171-180.

Karehanumappa, K (2013) Contribution of green pellet properties in induration of iron oxide pellet production. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 77-81.

Karmakar, A and Sivaprasad, S and Kundu, S and Chakrabarti, D (2014) Tensile Behavior of Ferrite-Carbide and Ferrite-Martensite Steels with Different Ferrite Grain Structures. Metallurgical and Materials Transactions A, 45A(4) (IF-1.730). pp. 1659-1664.

Karmakar, A and Sivaprasad, S and Nath, S K and Misra, R D K and Chakrabarti, D (2014) Comparison Between Different Processing Schedules for the Development of Ultrafine-Grained Dual-Phase Steel. Metallurgical and Materials Transactions A, 45A(5) (IF-1.730). pp. 2466-2479.

Kaushik, Rahul K and Sahu, J K (2011) Tensile behaviour of metallic materials and alloys. Training Report (TR). National Metallurgy Laboratory, Jamshedpur.

Kavipurapu, C S and Gupta, K K and Dasgupta, P and Chatterjee, N N and Pandey, L P (1993) Determination of boron in steels by inductively coupled plasma optical-emission spectrometry. Analusis, 21 (1). pp. 21-25.

Kavipurapu, C S and Srivastava, S C and Gupta, K K and Pandey , L P (1993) Extractive spectrophotometric method for the determination of niobium in steels. Mikrochimca Acta, 111 (1-3). pp. 127-132.

Kavitha, C and Ravichandran, K and Sankara Narayanan, T S N (2014) Effect of surface mechanical attrition treatment (SMAT) on zinc phosphating of steel. Transactions of the Institute of Metal Finishing, 92(3) (IF-0.747). pp. 161-168.

Kavitha, C and Sankara Narayanan, T S N and Ravichandran, K and Park, I S and Lee, Min Ho (2014) Deposition of zinc-zinc phosphate composite coatings on steel by cathodic electrochemical treatment. Journal of Coatings Technology and Research, 11(3) (IF- 1.280). pp. 431-442.

Kedia, Bipin and Panda, A K (2012) Modelling of the Electromagnetic Fluxes and Evaluation of Damage in Steels using Electromagnetic Techniques. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kenzhaliev, B K and Berkinbaeva, A N and Beisembaeva, G Zh. and Asilbekov, B and Suleimenov, E N (2010) Development of resource saving technology for gold recovery with intensifying additives. In: Proceedings of the XI International Seminar on Mineral Processing Technology (MPT-2010), Dec 2010, NML Jamshedpur, India.

Khadeer, S A and Babu, P R and Kumar, B Ravi and Kumar, A Seshu (2020) Evaluation of friction welded dissimilar pipe joints between AISI 4140 and ASTM A 106 Grade B steels used in deep exploration drilling. Journal of Manufacturing Processes, 56 (Part A) (IF-4.086). pp. 197-205.

Khairy, E M and Kamal, M. Hussein and El-Tawil, S Z (1966) Pre-oxidation of ilmenite ores and its bearing on their solid-state reduction by hydrogen. NML Technical Journal, 8 (2). pp. 10-14.

Khalilahmada, and Ali, Muhammad and Ibrahim , Ather and Baig, Waqas Mehmood (2014) Optimising the yield of silicon carbide synthesised from indigenous biomass husk using different catalysts. Journal of Metallurgy and Materials Science, 56(3) (NON-SCI). pp. 173-177.

Khan, Asghar and Chakraborty, N R and Yadav, H L (2013) Solar tracking with no movable parts using multiplexed holographic lenses for photovoltaic application. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 183-186.

Khan, S S and Rao, T R (2015) Multi objective optimization of turning parameters for Al 6061 using genetic algorithm. Journal of Metallurgy and Materials Science, 57(4) . pp. 243-249.

Khangaonkar, P R and Rahmat, A and Kutty, K G J (1992) Kinetic-study of the hydrothermal reaction between lime and rice-husk-ash silica. Cement &Concrete Research, 22 (4). pp. 577-588.

Khangaonkar, P R and Satyanarayana, C (1981) Liberation analysis and release analysis. Transactions of the institution of mining and metallurgy section c-mineral processing and extractive metallurgy, 90 (Sep). C113-C114.

Khangaonkar, P R and Subramani, K J B (1993) Flocculation of hematite fines by anionic polyacrylamide polymers. Minerals Engineering, 6 (7). pp. 765-774.

Khanra, A K and Pathak, L C and Godkhindi, M M (2009) Application of new tool material for electrical discharge machining (EDM). Bulletin of Materials Science, 32 (4). pp. 401-405.

Khanra, A K and Pathak, L C and Godkhindi, M M (2007) Carbothermal synthesis of zirconium diboride (ZrB2) whiskers. Advances in Applied Ceramics: Structural, Functional and Bioceramics Journal - Advances in Psychiatric Treatment, 106 (3). pp. 155-160.

Khanra, A K and Pathak, L C and Godkhindi, M M (2008) Double SHS of ZrB2 powder. Journal of Materials Processing Technology, 202 (1-3). pp. 386-390.

Khanra, A K and Pathak, L C and Godkhindi, M M (2007) Microanalysis of debris formed during electrical discharge machining (EDM). Journal of Materials Science, 42 (3). pp. 872-877.

Khanra, A K and Pathak, L C and Mishra, Suman K and Godkhindi, M M (2004) Effect of NaCl on the synthesis of TiB2 powder by a self-propagating high-temperature synthesis technique. Materials Letters, 58 (5). pp. 733-738.

Khanra, A K and Pathak, L C and Mishra, Suman K and Godkhindi, M M (2003) Self-propagating-high-temperature synthesis (SHS) of ultrafine ZrB2 powder. Journal of Materials Science Letters, 22 (17). pp. 1189-1191.

Khanra, A K and Pathak, L C and Mishra, Suman K and Godkhindi, M M (2005) Sintering of ultrafine zirconium diboride powder prepared by modified SHS technique. Advances in Applied Ceramics: Structural, Functional and Bioceramics Journal - Advances in Psychiatric Treatment, 104 (6). pp. 282-284.

Khanra, A K and Sarkar, B R and Bhattacharya, B and Pathak, L C and Godkhindi, M M (2007) Performance of ZrB2–Cu composite as an EDM electrode. Journal of Materials Processing Technology, 183 (1). pp. 122-126.

Kharia, D P (1981) A Glimpse of The Tata Iron and Steel Company Limited, Jamshedpur. In: International Symposium on Modern Developments in Steelmaking, February 15, 1981, NML, Jamshedpur.

Khatirkar, R K and Badole, R P and Vaish, A K and Humane, M M and De, P K and Paretkar, R K and Peshwe, D R and Prasad, D N (2003) Thermomechanical processing of low carbon, IF and IF high strength steels - A few typical cases. Journal of Metallurgy and materials Science, 45 (4). pp. 161-191.

Khattoi, S C and Roy, G G (2013) Sponge Iron Production From Ore-Coal Composite Pellets in Tunnel Kiln. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Khutia, N and Dey, P P and Paul, Surajit Kumar and Tarafder, S (2013) Development of non Masing characteristic model for LCF and ratcheting fatigue simulation of SA333 C–Mn steel. Mechanics of Materials, Volume 65, October 2013, Pages 88–102 (IF-1.936). pp. 88-102.

Khutia, N and Dey, P P and Sivaprasad, S and Tarafder, S (2014) Development of new cyclic plasticity model for 304LN stainless steel through simulation and experimental investigation. Mechanics of Materials, 78 (IF-2.225). pp. 85-101.

Kieffer, Richard and Benesovsky, Friedrich (1958) Sintered Materials on the base of Iron with Special Regard to Alloyed Sintered Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Kishore, Kaushal and Kumar, R Gaurav and Chandan, A K (2021) Critical assessment of the strain-rate dependent work hardening behaviour of AISI 304 stainless steel. Materials Science and Engineering A, 803 . p. 140675.

Kjellgren, Bengt R F (1961) Status of the Beryllium Industry in the United States of America. NML Technical Journal, 3 (1). pp. 37-45.

Klimenov, Vasiliy A and Kroning, Michael and Kroning, Paul and Mohr, Friedrich and Reddy, K M and Wolf, Helmut (2011) NDT Controlled Production in Steel Industry. In: Proceedings of International Conference on Nondestructive Evaluation for Steel and Allied Industries - NDESAI, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Kopparthi, Prasad and Simab, Rizwan and Banerjee, P K (2013) Performance Evaluation of Synthetic Collector on Coal Flotation. In: proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking , December 16-18, 2013, CSIR-NML Jamshedpur.

Koshiba, Eng. Sadao (1958) The Properties of High-speed Steel Derived from Magneic Iron Sand. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Krishna, K Gopala and Singh, Nidhi and Venkateswarlu, K and Kumar, K C Hari (2011) Tensile Behavior of Ultrafine-Grained Al-4Zn-2Mg Alloy Produced by Cryorolling. Journal of Materials Engineering and Performance, 20 (9). pp. 1569-1574.

Krishna, K Gopala and Sivaprasad, S and Sankara Narayanan, T S N and Kumar, K C Hari (2012) Localized corrosion of an ultrafine grained Al-4Zn-2Mg alloy produced by cryorolling. Corrosion Science, 60 . pp. 82-89.

Krishna, K Gopala and Sivaprasad, S and Venkateswarlu, K and Kumar, K C Hari (2012) Microstructural evolution and aging behavior of cryorolled Al–4Zn–2Mg alloy. Materials Science and Engineering A, 535 . pp. 129-135.

Krishna, S J G and Kumar, P S and Ravi, B P and Naganoor, P C and Yadav, S and Gundewar, C S (2013) Processing Studies on a Sub Grade Iron Ore Sample From S.J.H. Mine, Sandur, Karnataka. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, Dec 16-18,2013, CSIR-NML Jamshedpur.

Krishnan, V V (1994) Heat Treat Furnace Operations. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Krishnarao, R V and Godkhindi, M M and Chakraborty, M and Mukunda, P G (1994) Formation of sic whiskers from compacts of raw rice husks. Journal of Materials Science, 29 (10). pp. 2741-2744.

Krishnaveni, K and Sankara Narayanan, T S N and Seshadri, S K (2003) Electrodeposited Ni-B alloy films: Preparation and structural aspects. Transactions Of The Indian Institute Of Metals , 56 (4). pp. 341-346.

Kromhout, Jan and Carless, Stephen and Dekker, Edward (2013) Revealing The Unknown: Monitoring The in-Mould Behaviour During Continuous Casting of Steel. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Kumar, A and Chacko, Z E and Malathi, M and Godiwalla, K M and Ajmani, S K and Ranganathan, S (2014) Desulfurization of Hot Metal Through In Situ Generation of Magnesium in 30-kg Molten Iron Bath-Influence of Inert Gas Flow Rate. Steel Research International, 85(5) (IF-1.023). pp. 927-934.

Kumar, A and Singh, R J and Mitra, A and Panda, A K (2008) Preparation of Fe and Co based amorphous wires by in-water quenching process. Materials Science and Technology, 24 (5). pp. 618-622.

Kumar, A and Tarafder, S and Mukherjee, Surojit and Das, Swapan K and Ravi Kumar, B and Chattoraj, I (2003) Effect of plasma ion implantation on the hydrogen embrittlement of Cu strengthened HSLA-100 steel. Journal of Materials Science, 38 (12). pp. 2667-2671.

Kumar, A and Tripathi, B and Mishra, S and Kumar, P and Sharma, I H (2015) Power consumption and design optimization of a sustainable H fuel cell powered vehicle. Journal of Metallurgy and Materials Science, 57(3) . pp. 157-165.

Kumar, Anil and Khanna, A S and Banerjee, M K (2001) Epoxy coatings for rebar - A study. Journal of Metallurgy and materials Science, 43 (3). pp. 189-195.

Kumar, Anil and Ravi Kumar, B and Chattoraj, I and Mukherjee, S and Basumallick, A (2004) Alteration in hydrogen absorption by and hydrogen permeation through a high-strength low-alloy steel due to plasma source ion implantation of nitrogen. Metallurgical and Materials Transactions B, 35 (6). pp. 1123-1128.

Kumar, Anuj and Kumar, Sanjay (2013) Developments of Paving blocks from synergistic use of red mud and fly ash using geopolymerization. Construction and Building Materials, 38 . pp. 865-871.

Kumar, Anuvrat and Garai, Subhadra (2013) Insitu Bio Mineralization of Polymer-Hydroxyapatite Nano Composites as Bone Graft. Training Report (TR). CSIR-NML, Jamshedpur. (Unpublished)

Kumar, Avinash and Mrunmaya, K P and Maharana, Sudeep and Chowdhury, Subrata Kumar and Sah, Rameshwar and Kaza, Marutiram (2013) A Real Time Model For Prediction Of Blast Furnace Hot Temperature Through Neural Network. In: Proceeding of the International conference on science and technology of iron making and steel making , December 16-18, 2013, CSIR-NML Jamshedpur.

Kumar, B V and Mohanty, O N (1992) On the correct prediction of isothermal transformation diagrams for low carbon and low alloy steels — Comment on available data. Scripta Metallurgica et Materialia, 26 (1). pp. 133-137.

Kumar, Binod and Pramanick, A K (2010) A Dissertation Report on Hydrophilic Coating on Glass Substrate. Masters thesis, National Institute of Foundry and Forge Technology, Hatia, Ranchi.

Kumar, D Satish and Marutiram, K and Sah, Rameshwar (2013) Development of Integrated Process Control System at JSW Steel Ltd. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Kumar, Dhanranjan and Kumari, Munchun and Murugaiyan, Premkumar and Das, T K and Roy, Rajat K and Mitra, A and Shuvaeva, E and Churyukanov, M and Kaloshkin, S and Panda, A K (2020) Impact of uniaxial stress on soft-magnetic and magneto-impedance properties of vitrified magnetostrictive microwires. Journal of Alloys and Compounds, 831 (IF-4.175). p. 154861.

Kumar, Gaurav and Lichchhavi, and Pramanick, A K (2013) Characterization of Al-Si-Zr Alloy. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kumar, Gaurav and Lichchhavi, and Pramanick, A K (2013) Characterization of Al-Si-Zr Alloy. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kumar, Harendra and Mohapatra, J N and Roy, Rajat K (2010) Evaluation of tempering behaviour in modified 9Cr–1Mo steel by magnetic non-destructive techniques. Journal of Materials Processing Technology, 210 (4). pp. 669-674.

Kumar, M and Raj, I A and Pattabiraman, R (2008) Y2Zr2O7 (YZ)-pyrochlore based oxide as an electrolyte material for intermediate temperature solid oxide fuel cells (ITSOFCs) - Influence of Mn addition on YZ. Materials Chemistry and Physics, 108 (1). pp. 102-108.

Kumar, M and Srikanth, S and Ravi Kumar, B and Alex, T C and Das, Swapan K (2009) Synthesis of pure and Sr-doped LaGaO3, LaFeO3 and LaCoO3 and Sr,Mg-doped LaGaO3 for ITSOFC application using different wet chemical routes. Materials Chemistry and Physics, 113 (2-3). pp. 803-815.

Kumar, M Ashok and Reddy, G Ramachandra and Reddy, G Harinatha and Reddy, N Subbarami and Reddy, K Hemachandra and Reddy, Y V Mohana (2011) Mechanical properties of randomly oriented short Sansevieria trifasciata fibre/epoxy composites. Journal of Metallurgy and Materials Science, 53(1) . pp. 85-95.

Kumar, Manoj and Babu, M Nani and Mankhand, T R and Pandey, B D (2010) Precipitation of sodium silicofluoride (Na2SiF6) and cryolite (Na3AlF6) from HF/HCl leach liquors of alumino-silicates. Hydrometallurgy, 104 (2). pp. 304-307.

Kumar, Manoj and Mankhand, T R and Murthy, D S R and Mukhopadhyay, R and Prasad, P M (2007) Refining of a low-grade molybdenite concentrate. Hydrometallurgy, 86 (1-2). pp. 56-62.

Kumar, Manoj and Sau, D C and Nishant, P and Bhattacharya, Maitreyee (2013) Reduction of ammonium paratungstate generated during hydrometallurgical processing of tungsten-copper borings. Harnessing of Nonferrous Minerals and Wastes, 828 . pp. 123-134.

Kumar, Mukesh and Mishra, Suman K and Mitra, R (2013) Effect of Ar:N-2 ratio on structure and properties of Ni-TiN nanocomposite thin films processed by reactive RF/DC magnetron sputtering. Surface & Coatings Technology, 228 (IF-1.867). pp. 100-114.

Kumar, Nitesh and Kumar, Binay and Pathak, L C (2017) Effect of shapes and compositions of spark plasma sintered ZrB -C composites on performance as EDM 2 tools. Journal of Metallurgy and Materials Science, 59(4) . pp. 143-152.

Kumar, P and Prakash, R (1996) Quality assessment of class fibre composites by acousto ultrasonic technique. In: Trends in NDE science and technology - Proceedings of the 14th world conference on NDT, 1996, 14th WCNDT.

Kumar, P and Roy, A (2015) Creep damage and remaining life assessment of service exposed engineering materials used in petrochemical industry. Journal of Metallurgy and Materials Science, 57(1) . pp. 41-56.

Kumar, Piyush and Ravi Kumar, B (2012) Effect of Interrupted Annealing on Recrystallization of Heavily cold-rolled Austenatic Stainless Steel. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kumar, Pravesh (1998) Effect of fillers on acousto ultrasonic response in GRP composites. Bulletin of Materials Science, 21 (1). pp. 93-97.

Kumar, R Sandeep and Joshi, Deepa and Kumar, Yudhisther and Gupta, Reeta and Kumar, Ashok (2011) EMAT Based Ultrasonic System for Determination of Thickness Variation in Metallic Samples. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Kumar, Rajendra (1972) Immiscibility in binary-alloys of group Ia metals (lithium, sodium and potassium). Journal of materials science, 7 (12). pp. 1426-1433.

Kumar, Rajendra (1972) Immiscibility in binary-alloys of group IB metals (copper, silver and gold) - semi empirical approach. Journal of Materials Science, 7 (12). pp. 1409-1425.

Kumar, Rajendra and Bose, S K (1971) Structural stability of rapidly solidified Al---Cu super-saturated solid solutions. Scripta Metallurgica, 5 (6). pp. 515-518.

Kumar, Rajendra and Ray, R K and Biswas, A K (1992) A sem-edax study of sea nodules from central Indian-ocean basin. Transactions of The Indian Institute of Metals, 45 (5). pp. 287-301.

Kumar, Rajendra and Sivaramakrishnan, C S (1974) Distribution of copper and magnesium between molten aluminum and lead. Transactions of the Japan Institute of Metals, 15 (5). pp. 319-323.

Kumar, Rajendra and Sivaramakrishnan, C S (1972) Establishment of the Temperature Range of Accidental Overheating of Precipitation Hardened Aluminium-Copper Alloys. NML Technical Journal, 14 (1). pp. 16-23.

Kumar, Rajendra and Sivaramakrishnan, C S (1983) The influence of pseudosurfaces on solidification of aluminum-alloys. Transactions of the Indian Institute of metals, 36 (4). pp. 298-303.

Kumar, Rajendra and Sivaramakrishnan, C S (1983) Thermodynamics and structure of aluminum-alloys. Transactions of the Indian Institute of metals, 36 (4). pp. 253-258.

Kumar, Rakesh (1994) Leaching characteristics of disordered birnessite and goethite doped with ni, co and cu in sorption mode. Materials Transacrions JIM, 35 (1). pp. 27-34.

Kumar, Rakesh and Alex, T C (2015) Elucidation of the Nature of Structural Heterogeneity During Alkali Leaching of Non-activated and Mechanically Activated Boehmite (gamma-AlOOH). Metallurgical and Materials Transactions B- Process Metallurgy and Materials Processing Science, 46(4) . pp. 1684-1701.

Kumar, Rakesh and Das, S and Ray, R K and Biswas, A K (1993) Leaching of pure and cobalt bearing goethites in sulphurous acid: kinetics and mechanisms. Hydrometallurgy, 32 (1). pp. 39-59.

Kumar, Rakesh and Das, S K and Ray, R K and Biswas, A K (1994) A SEM backscattered electron mode study of microstructural features of ferromanganese nodules from central indian-ocean basin. Transactions of the indian institute of metals, 47 (5). pp. 273-285.

Kumar, Rakesh and Das, Samar (1998) Physicochemical and structural factors in the sulfuric acid leaching of nickel- and copper-bearing synthetic birnessites. Metallurgical and Materials Transactions B, 29 (3). pp. 527-540.

Kumar, Rakesh and Ray, R K (1998) Modeling Microstructural Heterogeneity in Materials by Using Q-Mode Factor Analysis. Materials Characterization, 40 (1). pp. 7-13.

Kumar, S and Rao, B N and Pradhan, B (2007) Effect of impactor parameters and laminate characteristics on impact response and damage in curved composite laminates. Journal of Reinforced Plastics and Composites, 26 (13). pp. 1273-1290.

Kumar, Sanjay and Agadi, W and Das, V K and Desai, B N (1994) Ultrasonic acoustic transducers for underwater acoustic measurements. In: Symposium on Ocean Technology, on the Occasion of the Golden Jubilee of the Council-of-Scientific-and-Industrial-Research (CSIR), Aug 27-29, 1992, Goa.

Kumar, Sanjay and Bandopadhyay, A and Alex, T C and Kumar, Rakesh (2006) Influence of mechanical activation on the synthesis and hydraulic activity of calcium dialuminate. Ceramics International, 32 (5). pp. 555-560.

Kumar, Sanjay and Bandopadhyay, A and Rajnikanth, V and Alex, T C and Kumar , Rakesh (2004) Improved processing of blended slag cement through mechanical activation. Journal of Materials Science, 39 (10). pp. 3449-3452.

Kumar, Sanjay and Das, Swapan K and Daspoddar, P K (2003) Thermo-mechanical behaviour of low cement castables derived from mullite aggregates synthesised from beach sand sillimanite. Ceramics International, 29 (2). pp. 139-144.

Kumar, Sanjay and Kristaly, Ferenc and Mucsi, Gabor (2015) Geopolymerisation behaviour of size fractioned fly ash. Advanced Powder Technology, 26(1) (IF-1.300). pp. 24-30.

Kumar, Sanjay and Kumar, Rakesh (2011) Mechanical activation of fly ash: Effect on reaction, structure and properties of resulting geopolymer. Ceramics International, 37 (2). pp. 533-541.

Kumar, Sanjay and Kumar, Rakesh (2010) Tailoring geopolymer properties through mechanical activation of fly ash. In: 2nd International conference on sustainable construction materials and technologies, 28-30 June, 2010, Ancona, Italy.

Kumar, Sanjay and Kumar, Rakesh and Bandopadhyay, A and Alex, T C and Ravi Kumar, B and Das, Swapan K and Mehrotra, S P (2008) Mechanical activation of granulated blast furnace slag and its effect on the properties and structure of portland slag cement. Cement and Concrete Composites, 30 (8). pp. 679-685.

Kumar, Sanjay and Kumar, Rakesh and Mehrotra, S P (2010) Influence of granulated blast furnace slag on the reaction, structure and properties of fly ash based geopolymer. Journal of Materials Science, 45 (3). pp. 607-615.

Kumar, Sanjay and Singh, K K (1998) Development of Corundum/Mullite Composites from fly Ash & Alumina Mix by Reaction Sintering. In: UNSPECIFIED.

Kumar, Sanjay and Singh, K K and Ramachandrarao, P (2001) Effects of fly ash additions on the mechanical and other properties of porcelainised stoneware tiles. Journal of Materials Science, 36 (24). pp. 5917-5922.

Kumar, Sanjay and Singh, K K and Ramachandrarao, P (2000) Synthesis of cordierite from fly ash and its refractory properties. Journal of Materials Science Letters, 19 (14). pp. 1263-1265.

Kumar, Suranjit and Kale, Rahul P and Singh, Pawan K and Ghosh, M and Chattopadhyay, J (2021) Fracture toughness behavior of dissimilar metal (SA508 Gr.3 Class 1 and SA312 Type 304LN) weld joint: With and without stress relieving treatment. Fatigue & Fracture of Engineering Materials and Structures, online .

Kumar, Surendra and Pradhan, B (1998) Three-Dimensional Finite Element Analysis of Composite Laminates Subjected to Transverse Impact. In: UNSPECIFIED.

Kumar, Vinay and Bagchi, D and Pandey, B D (1997) Separation of copper and zinc from complex sulphate solutions by using LIX84. Scandinavian Journal of Metallurgy, 26 (2). pp. 74-78.

Kumar, Vinay and Bagchi, D and Pandey, B D and Jana, R K and Premchand, (1996) Role of impurities in solvent extraction-electrowinning of copper and nickel for the processing of sea nodules. Transactions of the Indian Institute of Metals, 49 (6). pp. 753-760.

Kumar, Vinay and Pandey, B D and Agrawal, A and Bagchi, D and Kumari, S and Sahu, S K (2005) Value addition in the processing of copper bleed solution by solvent extraction process. In: Proceedings of the International solvent extraction conference, 2005.

Kumar, Vinay and Sahu, S K and Pandey, B D (2010) Prospects for solvent extraction processes in the Indian context for the recovery of base metals. A review. Hydrometallurgy, 103 (1-4). pp. 45-53.

Kumari, Anjan and Kumari, Archana and Jha, Manis K and Kumar, Vinod and Singh, R P and Yoo, Kyoungkeun (2014) Copper recovery from small devices populated on waste printed circuit boards. Journal of Metallurgy and Materials Science,, 56(1) (NON-SCI). pp. 41-51.

Kumari, Chitra and Nayar, S (2011) Biomimetic synthesis of aqueous ferrofluids using different polymers (STR). Training Report (TR). National Metallurgy Laboratory, Jamshedpur. (Submitted)

Kumari, Chitra and Nayar, S (2012) Morphological change of electrospun nanofibers of poly(vinyl) alchohol with three different biomimetic inorganic minerals. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kumari, K and Prasad, K and Yadav, K L and Sen, S (2009) Structural and Dielectric Properties of ZrO2 Added (Na1/2Bi1/2)TiO3 Ceramic. BRAZILIAN JOURNAL OF PHYSICS , 39 (2). pp. 297-300.

Kumari, Mamta and Prasad, J N (2008) Analysis of optimized sierpinski carpet (SC) fractal antenna and estimation of EMI. Journal of Metallurgy and Materials Science, 50 (4). pp. 235-243.

Kumari, S and Panda, A K and Mitra, A and Datta, J and Chattoraj, I (2006) Effect of hydrogen on the magnetic behavior of CoFeCrSiB amorphous. Journal of Materials Science, 41 (17). pp. 5510-5513.

Kumari, Sarita and Sahu, S K and Sharma, Vikram and Agrawal, A and Bagchi, D and Pandey, B D and Kumar, Vinay (2004) Synthesis of electrolytic copper and nickel powders from the copper bleed electrolyte of a copper smelter. In: Non Ferrous Meet - 2004, 2004.

Kumari, Seema and Chattoraj, I and Pal, S K and Mitra, A (2006) Study of Giant Magneto-Impedance Behavior in Co–Fe Based Amorphous/Nanocrystalline Materials. Materials and Manufacturing Processes, 21 . pp. 683-686.

Kumari, Seema and Chattoraj, I and Panda, A K and Mitra, A and Pal, S K (2006) Effect of Fe addition on the magnetic and giant magneto-impedance behaviour of CoCrSiB rapidly solidified alloys. Journal of Physics D: Applied Physics, 39 . pp. 2001-2006.

Kumari, Supriya (2012) Comparative Study on Biomimetically Synthesized Ferrofluid with the help of Sodium Hydroxide and Potassium Hydroxide. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Kundu, Subhashis and Nag, Samik and Kothari, Ajit and Ramna, R V and Rai, Shailendra and Roy, S K (2013) High Productivity and High Pci Operation at ‘H’ Blast Furnace, Tata Steel – The Operating Experiences with Indian Raw Materials. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, Dec 16-18,2013, CSIR-NML JSR.

Kushwaha, H S and Vaze, K K and Bhasin, V (2001) Design Criteria for Fracture Assessment of Pressurized Nuclear Components. In: UNSPECIFIED.

Kutumbarao, V V and Rajagopalachary, T (1994) Hot Workability and Processing Maps. In: Tailoring of properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

L

Lahiri, A K (2013) Failure of drain valve reducer in de-sulfurisation unit. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 257-270.

Lahiri, A K and Banerjee, T (1968) Electrochemical factors in the stress corrosion cracking of Cu alloys containing Zn and Mn. Corrosion Science, 8 (12). pp. 895-905.

Lahiri, A K and Banerjee, T (1965) Stress corrosion cracking of copper-manganese alloy. Corrosion Science, 5 (10). 731- .

Lahiri, A K and Banerjee, T and Nijhawan, B R (1967) Some observations on ancient iron. NML Technical Journal, 9 (2). pp. 32-33.

Lahiri, B B and Bagavathiappan, S and Saravanan, T and Rajkumar, K V and Kumar, Anish and Philip, John and Jayakumar, T (2011) Defect Detection in Weld Joints by Infrared Thermography. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Lahiri, R N (1980) Distillation of zinc .1. Vacuum distillation of zinc. Transactions of the Indian Institute of Metals, 33 (4). pp. 323-326.

Lakshmipathiraj, P and Bhaskar Raju, G and Basariya, M R and Parvathy, S and Prabhakar, S (2008) Removal of Cr (VI) by electrochemical reduction. Separation and Purification Technology, 60 (1). pp. 96-102.

Lakshmipathiraj, P and Narasimhan, B R V and Prabhakar, S and Bhaskar Raju, G (2006) Adsorption of arsenate on synthetic goethite from aqueous solutions. Journal of Hazardous Materials, 136 (2). pp. 281-287.

Lakshmipathiraj, P and Narasimhan, B R V and Prabhakar, S and Bhaskar Raju, G (2006) Adsorption studies of arsenic on Mn-substituted iron oxyhydroxide. Journal of Colloid and Interface Science, 304 (2). pp. 317-322.

Lakshmipathiraj, P and Prabhakar, S and Bhaskar Raju, G (2010) Studies on the electrochemical decontamination of wastewater containing arsenic. Separation and Purification Technology, 73 . pp. 114-121.

Lal, Kishori and Bhattamishra, A K and Nair, G G and Mukherjee, S P and Halder, B N and Kumar, Rajendra (1987) Failure of lead-antimony alloy sheathing for tele-communication cables during extrusion - a case-study. Transactions of the Indian Institute of metals, 40 (6). pp. 537-543.

Lal, Kishori and Dev, S C (1994) Processing of Non-ferrous Alloys through Extrustion. In: Tailoring of properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Lal, Kishori and Mahanti, R K and Sivaramakrishnan, C S (1992) Studies on Microstructure of Rapidly Solidified Aluminium-Transition metal Alloys with Misch Metal Addition. NML Technical Journal, 34 (1-2). pp. 18-26.

Lal, Kishori and Mahanti, R K and Sivaramakrishnan, C S (1992) Thermal-properties of lead and graphite dispersed rheocast aluminum silicon alloys by laser flash technique. Materials Transactions JIM, 33 (9). pp. 811-815.

Lal, Kishori and Mahanti, R K and Sivaramakrishnan, C S and Jain, K B (1991) Microstructure-property correlation in indigenously produced zinc-aluminum foundry alloys. Materials transactions, 32 (7). pp. 621-625.

Lal, Kishori and Mahanti, R K and Sivaramakrishnan, C S and Jain, K B (1991) Quality Improvement of Zn-AI Foundry Alloys through Melt Treatment. NML Technical Journal, 33 (3-4). pp. 3-9.

Lal, Kishori and Singh, Inder and Bhattamishra, A K and Kumar, Rajendra (1987) Characterization and selection of aluminum-alloy boomerang grab for sea nodules collection - a case-study. Transactions of the Indian Institute of metals, 40 (1). pp. 7-12.

Lal, S M and Ram, Mohan and Gundewar, C S (2013) Characterization and beneficiation of BHQ from Karnataka. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 323-327.

Lalitha, S and Chattopadhyay, S and Das, Suchandan K and Godiwalla, K M (1991) Simulation of heat-transfer in the continuous-casting mold. Transactions Of The Indian Institute Of Metals , 44 (1). pp. 89-92.

Lalitha, S and Chattopadhyay, S and Ghosh, R N (1990) Development of software on finite-element mesh generation (meshgen) for metallurgical applications. Engineering Fracture Mechanics, 36 (3). pp. 527-530.

Lee, Jin-Young and Jha, Amrita Kumari and Kumari, Archana and Kumar, J Rajesh and Jha, Manis K and Kumar, Vinay (2011) Neodymium recovery by precipitation from synthetic leach liquor of concentrated rare earth mineral. Journal of Metallurgy and Materials Science, 53 (4). pp. 349-354.

Lee, Taejong and Lee, Soowhan and Kim, Nohyu and Lim, Jongsoo (2011) Thermo-graphic Detection of Surface Cracks. In: Proceedings of the International Conference on Nondestructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Lendave, S A and Karande, V S and Deskmukh, L P (2010) Structural and transport characteristics of HgxCd1-xS thin composite films : A correlation. Journal of Metallurgy and Materials Science, 52 (4). pp. 363-370.

Lenka, Suvendu (2011) Basic Technique, Limitation and Application of Guided Waves, Phased Array and Electro-Magnetic Acoustic Transducer(EMAT). In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Li, X and Jiao, F and Al-Samman, T and Ghosh Chowdhury, S (2012) Influence of second-phase precipitates on the texture evolution of Mg–Al–Zn alloys during hot deformation. Scripta Materialia, 66 (3-4). pp. 159-162.

Liu, J and Zhou, L and Hao, X J and Strangwood, M and Peyton, A and Morris, P F and Davis, C L (2011) Non-destuctive Evaluation of Power-Generation Steel Microstructure Changes Using Electromagnetic Sensors. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries NDESAI - 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Lodhari, D R and Dutta, S K and Shah, R V (2013) Effect Of Aluminium, Chromium, Niobium And Titanium On On steel. In: Proceding of the International Confercnce on Science and technology of ironmaking and steel making, December 16-18, 2013, CSIR-NML Jamshedpur.

Lunawat, C B and Todi, V N (1994) Technology of Steel Tube Making. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

M

Madge, S V and Caron, A and Gralla, R and Wilde, G and Mishra, Suman K (2014) Novel W-based metallic glass with high hardness and wear resistance. Intermetallics, 47 (IF-1.696). pp. 6-10.

Madge, S V and Louzguine, D V and Inoue, A and Greer , A L (2013) Large Compressive Plasticity in a La-Based Glass-Crystal Composite. Metals, 3(1) (IF-). pp. 41-48.

Mahanti, R K and Lal, Kishori and Sinha, A N and Sivaramakrishnan, C S (1993) A novel technique for hyper eutectic aluminum-silicon alloy melt treatment. Materials Transactions JIM, 34 (12). pp. 1207-1211.

Mahanti, R K and Lal, Kishori and Sinha, A N and Sivaramakrishnan, C S (1993) Novel technique for hyper eutectic aluminum-silicon alloy melt treatment. Materials Transactions Jim, 34 (12). pp. 1207-1211.

Mahanty, M S and Misra, R N and Bhatnagar, P P (1968) Studies on the extraction of nickel from a low-grade nickel-ferrous ore from Rajasthan. NML Technical Journal, 10 (1). pp. 15-17.

Mahapatra, A K S and Dhananjayan, N (1981) Electrophoretic deposition of silicon-carbide. Transactions of the Indian Institute of metals, 34 (6). pp. 495-500.

Mahapatra, A K S and Goswami, M C and Gupta, K N (1991) Evaluation of physico-chemical characteristics of some Indian iron ores and sinters. NML Technical Journal, 33 (1). pp. 9-16.

Mahato, B and Sahu, T and Shee, S K and Sahu, Puspendu and Sawaguchi, Takahiro and komi, J and Karjalainen, L P (2017) Simultaneous twinning nucleation mechanisms in an Fe–Mn–Si–Al twinning induced plasticity steel. Acta Materialia, 132 (IF-5.301). 264-275.

Mahato, B and Shee, S K and Sahu, T and Ghosh Chowdhury, S and Sahu, Puspendu and Porter, D A and Karjalainen, L P (2015) An effective stacking fault energy viewpoint on the formation of extended defects and their contribution to strain hardening in a Fe-Mn-Si-Al twinning-induced plasticity steel. Acta Materialia, 68 (IF-2.380). pp. 69-79.

Mahato, D K and Chaudhary, R K and Bhattamishra, A K and Srivastava, S C (2004) Synthesis and characterization of some PLNZT ceramics. Journal Of Materials Science-Materials In Electronics, 15 (9). pp. 575-578.

Mahato, D K and Chaudhary, R K and Das , N N and Srivastava, S C (2003) Thermal behaviour of spray dried PZT and PLNZT powders. Indian Journal Of Pure & Applied Physics , 41 (10). pp. 767-770.

Mahato, D K and Chaudhary, R K and Srivastava, S C (2005) Dielectric behaviour of spray dried Pb0.98(La1−x/3Nax)0.02(Zr0.53Ti0.47)0.9950O3 system. Journal of Materials Science, 40 (2). pp. 381-386.

Mahato, D K and Chaudhary, R K and Srivastava, S C (2003) Effect of Na on microstructure, dielectric and piezoelectric properties of PZT ceramic. Journal of Materials Science Letters, 22 (22). pp. 1613-1615.

Mahato, M M and Agrawal, M K and Sinha, S N (2013) Production of low sulphur spheroidal graphite pig iron in mini blast furnace by optimising slag. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 201-208.

Mahato, M M and Agrawal, M K and Sinha, S N (2010) Production of sg grade pig iron by optimising slag chemistry in mini blast furnace. In: Proceedings of the XI International Seminar on Mineral Processing Technology (MPT-2010), Dec 2010, NML Jamshedpur, India.

Mahato, P and Banerjee, P and Murmu, Manilal and Hirani, Harish and Murmu, N C and Mishra, Suman K (2021) Investigation on Multifunctional Properties of Sputtered Ti-Si-B-C Coating with Varied Thickness over Targeted Surface. Journal of Materials Engineering and performance .

Mahato, P and Singh, R J and Mishra, Suman K (2016) Nanocomposite Ti-Si-B-C hard coatings deposited by magnetron sputtering: Oxidation and mechanical behaviour with temperature and duration of oxidation. Surface & Coatings Technology, 288 (IF- 2.589). pp. 230-240.

Mahato, R Raman and Jayakrishnan, P and Bhattamishra, A K and Singh, Ratnakar (2001) Corrosion behaviour of painted HSLA panels in chloride environment a comparative study of different paints. Anti-Corrosion Methods and Materials , 48 (3). pp. 188-193.

Mahere, Vishesh and Nigam, S P (2006) Identification of Isomorphism and Structural Properties of Kinematic chains with the help of Adjacency matrices. Journal of Metallurgy and Materials Science, 48 (1). pp. 31-44.

Maheswari, N and Ghosh Chowdhury, S and Kumar, K C Hari and Sankaran, S (2014) Influence of alloying elements on the microstructure evolution and mechanical properties in quenched and partitioned steels. Materials Science and Engineering A, 600 (IF- 2.409). pp. 12-20.

Maity, P C and Panigrahi, S C (1998) Production of Aluminium Matrix In - Situ Particulate Copmosites. In: UNSPECIFIED.

Maity, S and Chakravarty, S and Bhattacharjee, S and Roy, B C (2005) A study on arsenic adsorption on polymetallic sea nodule in aqueous medium. Water Research, 39 (12). pp. 2579-2590.

Maity, S and Chakravarty, S and Thakur, P and Gupta, K K and Bhattacharjee, S and Roy, B C (2004) Evaluation and standardisation of a simple HG-AAS method for rapid speciation of As(III) and As(V) in some contaminated groundwater samples of West Bengal, India. Chemosphere - Global Change Science, 54 (8). pp. 1199-1206.

Maity, S K and Ballal, N B and Goldhahn, G and Kawalla, R (2008) Development of low alloy titanium and niobium microalloyed ultrahigh strength steel through electroslag refining. Ironmaking & Steelmaking, 35 (5). pp. 379-386.

Maity, S K and Ballal, N B and Goldhahn, G and Kawalla, R (2008) Development of low alloy ultrahigh strength steel. Ironmaking & Steelmaking, 35 (3). pp. 228-240.

Maity, S K and Ballal, N B and Goldhahn, G and Kawalla, R (2009) Development of Ultrahigh Strength Low Alloy Steel through Electroslag Refining Process. ISIJ International, 49 (6). pp. 902-910.

Maity, S K and Ballal, N B and Kawalla, R (2006) Development of ultrahigh strength steel by electroslag refining: Effect of inoculation of titanium on the microstructures and mechanical properties. ISIJ International, 46 (9). pp. 1361-1370.

Maity, S K and Rajak, A K and Chandra Shekhar, M and Singh, S D (2014) Development of 0.2C-CrMnMoV Ultra High Strength Steel. International Journal of Scientific Engineering and Technology, 3(2) . pp. 101-108.

Maity, S K and Rajak, A K and Shekhar, M Chander and Singh, S D (2016) Development of Ultra High Strength Steel by Electroslag Refining and Thermomechanical Treatment. Transations of the Indian Institute Metals, 69(3) (IF- 0.533). pp. 705-716.

Maji, K D (1974) Preferred orientation in extruded aluminum-alloy and aluminum rods. Indian Journal of Technology, 12 (9). pp. 391-394.

Majumdar, J Dutta and Nath, A K and Ravi Kumar, B and Manna, I (2004) Studies on residual stress developed in laser surface irradiated 0.6% carbon steel. Optics and Lasers in Engineering, 14 (3-4). pp. 133-151.

Malcor, H (1959) Experience with Low-Shaft Furnace at Ougree. NML Technical Journal, 1 (1). pp. 88-104.

Mallar, Ray and Bandopadhyay, N R and Ghanta, Ujjwal and Klie, Robert F and Pramanick, A K and Das, Samaresh and Ray, Samit K and Hossain, S M (2011) Temperature dependent photoluminescence from porous silicon nanostructures: Quantum confinement and oxide related transitions. Journal of Applied Physics, 110 (9). p094309-1-p094309-8.

Mallick, B and Maity, P C and Sinha, V K (1998) Production of Aluminium-Silicon Carbide Cast Particle Composites Without Magnesium. In: UNSPECIFIED.

Mallik, D and Mir, Aparna and Bhattacharya, S and Nayar, S (2011) Fluorimetric assay of interaction of protein with ferrofluids. Spectrochimica Acta Part A-Molecular And Biomolecular Spectroscopy , 78 (1). pp. 332-336.

Mallikarjun, K and Suwas, S and Ghosh Chowdhury, S and Bhargava, S (2003) Effect of prior beta processing steps on microstructural refinement during thermomechanical processing of a two phase (alpha+beta) titanium alloy. Materials Science and Technology, 19 (12). pp. 1688-1696.

Mandal, Anup and Guguloth, K and Bandyopadhyay, T K (2016) Characterization of Microstructure and Mechanical Properties of 9.2Cr0.45V0.7C Heat-Resistant Steel. Metallography, Microstructure, and Analysis, 5(2) (IF-0.58). pp. 95-107.

Mandal, C and Mishra, A K and Prasad, R R and Avtar, Ram and Mukerjee, D (2011) A non destructive method to detect the incipient fault in rolling element bearing. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Mandal, D (2008) Effect of wt% Reinforcement on Mechanical and Wear Properties of Al-2Mg base short copper Coated Steel Fiber Composites. In: Seminar on Growth with Quality Challenges & Opportunities for foundry, January 18-19, 2008, TMDC Auditorium, Jamshedpur.

Mandal, D (2008) Effect of wt% Reinforcement on Mechanical and Wear properties of Al-2mg base Short Copper Coated Steel Fiber Composites. In: Seminar on Growth with Quality Challenges & Opportunities for foundry, January 18-19, 2008, TMDC Auditorium, Jamshedpur.

Mandal, D and Dutta, B K and Panigrahi, S C (2007) Dry sliding wear behavior of stir cast aluminium base short steel fiber reinforced composites. Journal of Materials Science, 42 (7). pp. 2417-2425.

Mandal, D and Dutta, B K and Panigrahi, S C (2008) Effect of wt% reinforcement on microstructure and mechanical properties of Al-2Mg base short steel fiber composites. Journal of Materials Processing Technology, 198 (1-3). pp. 195-201.

Mandal, D and Dutta, B K and Panigrahi, S C (2010) Influence of coating and alloy additions on distribution of fibres and hardness of cast aluminium base short steel fibre reinforced composites. Materials Science and Technology, 26 (2). pp. 157-163.

Mandal, D and Dutta, B K and Panigrahi, S C (2007) Influence of coating on short steel fiber reinforcements on corrosion behavior of aluminium base short steel fiber reinforced composites. Journal of Materials Science, 42 (8). pp. 2796-2801.

Mandal, D and Dutta, B K and Panigrahi, S C (2007) Influence of mechanical working on properties of aluminium base short steel fiber reinforced composites. Influence of mechanical working on properties of aluminium base short steel fiber reinforced composites , 42 (20). pp. 8622-8628.

Mandal, D and Dutta, B K and Panigrahi, S C (2006) Microstructure and mechanical properties of Al–2Mg alloy base short steel fiber reinforced composites prepared by vortex method. Journal of Materials Science, 41 (15). pp. 4764-4770.

Mandal, D and Dutta, B K and Panigrahi, S C (2007) Processing and mechanical properties of Al, A-Mg-2 and Al-Cu-4 alloy base short steel fibre reinforced composites prepared by vortex method. Materials Science and Technology, 23 (1). pp. 23-28.

Mandal, D and Dutta, B K and Panigrahi, S C (2008) Wear properties of copper-coated short steel fiber reinforced stir cast Al–2Mg alloy composites. Wear, 265 (5-6). pp. 930-939.

Mandal, D and Ghosh, M and Pal, J and De, P K and Das, Goutam and Das, Swapan K and Ghosh Chowdhury, S and Lakra, B A and Ghosh, Sukomal (2006) Development of Cast Austempered Fe-Si-Mn-ME (Microalloying Elements) Steels. Exploratory (OLP). CSIR-NML, Jamshdpur. (Submitted)

Mandal, D and Ghosh, M and Pal, J and De, P K and Ghosh Chowdhury, S and Das, S K and Das, Goutam and Ghosh, Sukomal (2008) Influence of Austempering Temperature on Microstructure and Mechanical Properties of Cast Fe-Si-Mn-VSteel. In: 60 Annual Technical Meeting, November, 15-16, 2008, NML, Jamshedpur.

Mandal, D and Ghosh, M and Pal, J and De, P K and Ghosh Chowdhury, S and Das, S K and Das, Goutam and Ghosh, Sukomal (2006) Influence of Austempering Temperature on Microstructure and Mechanical Properties of Cast Fe-Si-Mn-VSteel. In: 60 Annual Technical Meeting, November, 14-16, 2006, NML, Jamshedpur.

Mandal, D and Ghosh, M and Pal, J and Ghosh Chowdhury, S and Das, Goutam and Das, Swapan K and Ghosh, Sukomal (2014) Evolution of microstructure and mechanical properties under different austempering holding time of cast Fe–1.5Si–1.5Mn–V steels. Materials & Design, 54 (IF-3.171). pp. 831-837.

Mandal, D and Viswanathan, S (2013) Effect of heat treatment on microstructure and interface of SiC particle reinforced 2124 Al matrix composite. Materials Characterization, 85 (IF-1.880). pp. 73-81.

Mandal, D and Viswanathan, S (2013) Effect of re-melting on particle distribution and interface formation in SiC reinforced 2124Al matrix composite. Materials Characterization, 86 . pp. 21-27.

Mandal, G K and Balasubramaniam, R and Mehrotra, S P (2009) Theoretical Investigation of the Interfacial Reactions during Hot-Dip Galvanizing of Steel. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science, 40-A (3). pp. 637-645.

Mandal, G K and Das, Swapan K and Balasubramaniam, R and Mehrotra, S P (2010) Effect of Elevated Strip Entry Temperature on the Aluminum Rich Inhibition Layer at the Substrate Coating Interface During Galvanizing. Canadian Metallurgical Quarterly , 49 (3). pp. 301-309.

Mandal, G K and Mandal, D and Das, S K and Balasubramaniam, R and Mehrotra, S P (2009) Microstructural study of galvanized coatings formed in pure as well as commercial grade zinc baths. Transactions of the Indian Institute of Metals, 62 (1). pp. 35-40.

Mandal, G K and Mandal, D and Das, S K and Balasubramaniam, R and Mehrotra, S P (2007) Microstructural Study of Galvanized coatings formed in Pure as well as Commercial Grade Zn Baths. In: International Conference on Metals and Alloys : Past, Present and Future Metallo-2007, Dec. 7-10, 2007, NML, Jamshedpur.

Mandal, G K and Sau, D C and Das, Suchandan K and Bandyopadhyay, D (2014) A Steady State Thermal and Material Balance Model for an Iron Making Blast Furnace and Its Validation with Operational Data. Transaction of the Indian Institute of Metals, 67(2) (IF-0.427). pp. 209-221.

Mandal, G K and Stanford, Nicole and Hodgson, Peter and Beynon, John H (2013) Static recrystallisation study of as-cast austenitic stainless steel. Materials Science and Engineering A, 576 (IF-2.108). pp. 118-125.

Mandal, R K and Pramanick, A K and Sastry, G V S and Lele, S (2004) Unique Indexing Scheme of Decagonal Phases based on a six Dimensional Model. Materials Resources Society Symposium Proceedings, 805 . LL1.6.1-LL1.6.10.

Mandal, S and Chakraborty, A and Ghosh, S K and Chatterjee, S (2013) Thermomechanically Controlled Processed Low Carbon Ultra Strength Steel: Microstructure and Mechanical Properties. In: Proceedings of the International Conference on Science and technology of Ironmaking and steel making, March 8-10, 2006, NML, Chennai.

Mandal, S K (1994) On the Metallurgical Design of Carburised Gears. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Mandal, S K (2010) Study of particle dynamics in Floatex Density Separator through image processing and analysis technique. In: Proceedings of First International Joint Conference on Information & Communication Technology 09-10 January 2010, January 09-10, 2010, Interscience Institute of Management & Technology, Bhubaneswar.

Mandal, Soumen and Sivakumar, B and Singhbabu, Y N and Bandyopadhyay, N R and Chattopadhyay, P P and Kailath, A J (2019) Electrochemical Behavior of Cu 60 Zr 25 Ti 15 Bulk Metallic Glass with the Addition of Nb and Mo. Journal of Materials Engineering and Performance, 28 (IF-1.476). pp. 6874-6884.

Mandal, Sudipta and Rao, Venkatesh and Ray, Ajoy K (2004) Characterization of the brazed joint interface between Al2O3 and (Ag-Cu-Ti). Journal of Materials Science, 39 (16-17). pp. 5587-5590.

Mandal, Sudipta and Ray, Ashok K and Ray, Ajoy K (2004) Correlation between the mechanical properties and the microstructural behaviour of Al2O3–(Ag–Cu–Ti) brazed joints. Materials Science and Engineering A, 383 (2). pp. 235-244.

Mandhyan, Ajay and Chattoraj, I and Mishra, Suman K and De, P K (2006) Study of Hydrogen Permeation Behaviour of High Strength Aluminium Alloys. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Mandhyan, Mala and Parmar, Kavita and Mandhyan, A K (2007) Eco-friendly inhibition of mild steel in acidic media. Journal of Metallurgy and Materials Science, 49 (2). pp. 123-128.

Mangalam, V and Khangaonkar, P R (1984) Flotation behavior of magnesite with carboxylic-acid collectors and a chelating agent. Transactions of the Indian Institute of metals, 37 (6). pp. 730-737.

Mangalam, V and Khangaonkar, P R (1985) Zeta-potential and adsorption studies of the chalcopyrite-sodium diethyl dithio carbamate system. International Journal of Mineral Processing, 15 (4). pp. 269-280.

Mangalam, V and Khangaonkar, P R (1983) Zeta-potential and flotation studies of chalcopyrite fines with 8-hydroxy quinoline. Colloids and Surfaces A Physicochemical and Engineering Aspects, 7 (3). pp. 209-220.

Mangalam, V and Khangaonkar, P R (1987) Zeta-potential and flotation studies of chalcopyrite fines with cupferron. Transactions of the Indian Institute of metals, 40 (1). pp. 49-54.

Manoharan, S S and Singh, Brajendra and Sahu, Ranjan K and Zimmer, A and Lim, S -H and Salamanca-Riba, L G and Chandrasekar, V (2008) Effect of Ru-Mn redox interactions on the hole carrier density in pulsed electron deposited La1-xPbxMn0.8Ru0.2O3 (0.2 <= x <= 0.4) thin films. Journal Of Physics-Condensed Matter, 20 (23). p. 235205.

Maranga, S M and Bett, Alvin Kiprono and Ndeto, Kyalo and Bett, Gilbert (2013) Kenyan Iron Ore: Mining and prospects of Processing. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Marinelli, María Cecilia and Giertler, Alexander and Sahu, J K and Herenu, Silvina and Alvarez-Armas, Iris and Krupp, Ulrich (2012) The Effect of Ferrite Embrittlement in Duplex Steel on Fatigue Crack Propagation from the Low (LCF) to the Very High Cycle Fatigue (VHCF) Regime. In: 19th EUROPEAN CONFERENCE ON FRACTURE, Fracture Mechanics for Durability, Reliability and Safety, August 26-31, 2012, Kazan, Russia.

Maruoka, Nobuhiro and Song, Duk-Yong and Shibata, Hiroyuki and Kitamura, Shin-ya and Gupta, G S (2013) Emulsification of Metal in Molten Salt by Gas Bubblin. In: Proceeding of The International Conference on Science and Technology of Ironmaking and Steelmaking, Dec 16-18,2013, CSIR-NML JSR.

Mathew, M D and Rao, K B S and Mannan, S L and Paknikar, K and Singh, R (2000) Recovery of creep properties of alloy 625 after long term service. Creep and Fracture Of Engineering Materials and Structures, 171 (1). pp. 537-543.

Maulik, S C (1997) R&D on beneficiation and sintering of iron ore at national metallurgical laboratory (NML). Ironmaking resources and reserves estimation, (5). pp. 203-209.

Maulik, S C and Patnaik, H and Chakravorty, N (1988) Development of a non-linear regression model for iron ore sintering. NML Technical Journal, 30 (1-4). pp. 17-24.

Mayer, G (1958) Some Recent Advances in the Study of Transformations in Alloy Steels. In: Symposium on Production, Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Mazinan , Vahid and Nosrati , Hassan (2014) Effect of primary materials ratio and their stirring time on SiC nanoparticle production efficiency through sol gel process. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 29-34.

Mazinani, Vahid (2014) Effect of pH on SiC nanopowder synthesized by sol-gel method. Journal of Metallurgy and Materials Science, 56(2) (NON-SCI). pp. 143-147.

Mazumdar, Dipak (2013) Ladle Metallurgy Steelmaking: The Role of Physical and Mathematical Modeling. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

McFarlane, J (1958) Silicon Steel Sheets - An outline of Properties Applications and Recent Developments. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Meena, Dilip and Raj, Manish and Ranghuwansh, Mansingh and Garg, Vivek and Lakshminarasimham, B (2013) Effect of Iron Ore Lumps and Iron Ore Pellets on Production of Direct Reduced Iron. In: Proceeding of the international coconference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Mehrotra, S P and Singh, Ratnakar (1994) Role of froth processes on flotation. Metals Materials and Processes, 6 (3). pp. 195-216.

Mehta, K D and Das, Chitrangada and Kumar, Rakesh and Pandey, B D and Mehrotra, S P (2010) Effect of mechano-chemical activation on bioleaching of Indian Ocean nodules by a fungus. Minerals Engineering, 23 . pp. 1207-1212.

Mehta, K D and Pandey, B D and Premchand, (1999) Bio-assisted leaching of copper, nickel and cobalt from copper converter slag. Materials Transactions JIM, 40 (3). pp. 214-221.

Meshram, Pratima and Abhilash, and Pandey, B D and Mankhand, T R and Deveci, Haci (2016) Comparision of Different Reductants in Leaching of Spent Lithium Ion Batteries. Journals of Metals, 68(10) (IF-1.860). pp. 2613-2623.

Metya, Avijit Kumar and Bar, H N and Parida, N and Das, S K (2011) Failure Analysis of Ball Clevis of 320KN Hardware Fittings. Sponsored (SSP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Metya, Avijit Kumar and Parida, N and Bhattacharya, D K and Bandopadhyay, N R and Palit Sagar, S (2007) Assessment of Localized Plastic Deformation during Fatigue in Polycrystalline Copper by Nonlinear Ultrasonic. Metallurgical and Materials Transactions A, 38 (12). pp. 3087-3092.

Metya, Avijit Kumar and Rajnikanth, V and Prakash, Amit and Das, S K (2011) Failure Analysis of Compressor Blade of SU-30MKI(SB-142). Other (TMP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Metya, Avijit Kumar and Rajnikanth, V and Prakash, Amit and Parida, N (2011) Metallurgical Analysis of 1st Stage LPC Compressor Blade of SU-30 MKI SB-062 (No.25). Sponsored (SSP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Miller, J R (1958) The Mysore Iron and Steel Works as a Major Producer of Stainless Steel in India. In: Symposium on Production, Properties, and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Minj, R K and Singh, S D and Ghorai, S and Paswan, Dayanand and Bandyopadhyay, D (2013) Development of a suitable process for effective and efficient de-phosphorisation of liquid metal in induction furnace. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Mir, Aparna and Mallik, D and Bhattacharya, S and Mahata, D and Sinha, Arvind and Nayar, S (2010) Aqueous ferrofluids as templates for magnetic hydroxyapatite nanocomposites. Journal of Materials Science-Materials in Medicine, 21 (8). pp. 2365-2369.

Mironov, V G and Kenzhaliev, B K and Shilov, G T and Mahato, M M and Kalinin, V Yu and Suleimenov, E N (2013) The Conditions For Producing of New Iron-Based Filler Alloy For The Reconstruction Of Varied Machines' And Equipment' Parts By Mechanical Alloying Method. In: Proceeding of the International Conference on science and technology of Iron making and steel making, December 16-18, 2013, CSIR-NML Jamshedpur.

Mishra, Aadarsh (2014) The films of tin sulphide for use in thin film solar cell devices. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 73-76.

Mishra, D K and Mohapatra, J and Mahato, Banashree and Kumar, P and Mitra, A and Singh, S K and Kanjilal, D (2013) Effect of 1.2 MeV argon ions irradiation on magnetic properties of ZnO. Applied Surface Science, 282 (IF-2.112). pp. 954-959.

Mishra, Gangotri and Kumar, Rajendra (1966) Development of an ice calorimeter for high temperature calorimetry. NML Technical Journal, 8 (3). pp. 11-14.

Mishra, Gangotri and Kumar, Rajendra (1967) Heat contents and heat capacities of liquid lead-antimony alloys. NML Technical Journal, 9 (4). pp. 18-21.

Mishra, H N and Das, Chitrangada (2003) A review on biological control and metabolism of aflatoxin. Critical Reviews in Food Science and Nutrition, 43 (3). pp. 245-264.

Mishra, K K (1994) Heat Treatment of Rolls. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Mishra, K K (1997) Joint design in welding. Journal of materials processing & manufacturing science, 5 (4). pp. 303-315.

Mishra, K K and Pavelic, V and Baker, G S (1996) Strip welding of aluminum bronze. Journal of materials processing & manufacturing science, 4 (3). pp. 243-267.

Mishra, Prerna and Rajpurohit, R S and Srinivas , N C S and Sastry, G V S and Singh, Vakil (2020) Ratcheting Fatigue Behavior of Modified 9Cr-1Mo Steel at Room Temperature. Metals and Materials International, Online (IF-1.990).

Mishra, Purusottam Narayana and Singh, S N and Dev, S C and Basak, P and Roy, A and Mohanty, A (1993) An instrumentation system for evaluation of contact materials. Measurement science & technology, 4 (2). pp. 221-225.

Mishra, Sujata and Bhatta, B C (2013) Solvent Extraction of Zr (IV) from HCl medium using Cyanex 923 as extractant in kerosene. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 299-304.

Mishra, Suman K (2009) Nano and Nanocomposite Superhard Coatings of Silicon Carbonitride and Titanium Diboride by Magnetron Sputtering. INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 6 (3). pp. 345-354.

Mishra, Suman K and Bhattacharyya, A S (2008) Effect of substrate temperature on the adhesion properties of magnetron sputtered nano-composite Si–C–N hard thin films. Materials Letters, 62 (3). pp. 398-402.

Mishra, Suman K and Bhattacharyya, A S and Mahato, P and Pathak, L C (2012) Multicomponent Ti-Si-B-C superhard and tough composite coatings by magnetron sputtering. Surface and Coatings Technology, 207 . pp. 19-23.

Mishra, Suman K and Bhattacharyya, A S and Rupa, P K P and Pathak, L C (2012) XPS Studies on Nanocomposite Si-C-N Coatings Deposited by Magnetron Sputtering. Nanoscience and nanotechnology letters, 4 (3). pp. 352-357.

Mishra, Suman K and Bhople, A and Paswan, S (2014) Microstructure, hardness, toughness and oxidation resistance of Al2O3-ZrB2 composite with different Ti percentages prepared by in-situ SHS dynamic compaction. International Journal of Refractory Metals and Hard Materials, 43 (IF-1.764). pp. 7-12.

US2003000393398 (2005) Process for the production of zirconium boride powder. US6908599.

Mishra, Suman K and Das, Swapan K (2005) Sintering and microstructural behaviour of SHS produced zirconium diboride powder with the addition of C and TiC. Materials Letters, 59 (27). pp. 3467-3470.

Mishra, Suman K and Das, Swapan K and Das, S K and Ramachandrarao, P (2000) Sintering studies on ultrafine ZrB2 powder produced by a self-propagating high-temperature synthesis process. Journal of Materials Research, 15 (11). pp. 2499-2504.

Mishra, Suman K and Das, Swapan K and Ramachandrarao, P (2002) Microstructure evolution during sintering of self-propagating high-temperature synthesis produced ZrB2 powder. Journal of Materials Research, 17 (11). pp. 2809-2814.

Mishra, Suman K and Das, Swapan K and Ramachandrarao, P and Belov, D Yu and Mamyan, S (2003) Synthesis of zirconium diboride-alumina composite by the self-propagating, high-temperature synthesis process. Metallurgical and Materials Transactions A, 34 (9). pp. 1979-1983.

Mishra, Suman K and Das, Swapan K and Ramachandrarao, P and Blov, D Y (2004) Self-propagating high-temperature synthesis of a zirconium diboride-alumina composite: a dynamic X-ray diffraction study. Philosophical Magazine Letters Online ISSN 1362-3036, 84 (1). pp. 41-46.

Mishra, Suman K and Das, Swapan K and Ray, Ajoy K and Ramachandrarao, P (1999) Effect of nickel on sintering of self-propagating high-temperature synthesis produced titanium carbide. Journal of Materials Research, 14 (9). pp. 3594-3598.

Mishra, Suman K and Das, Swapan K and Sherbacov, V (2007) Fabrication of Al2O3–ZrB2 in situ composite by SHS dynamic compaction: A novel approach. Composites Science and Technology, 67 (11-12). pp. 2447-2453.

Mishra, Suman K and Das , S and Goel, R P and Ramachandrarao, P (1997) Self-propagating high temperature synthesis (SHS) of titanium carbide. Journal of Materials Science Letters, 16 (12). pp. 965-967.

Mishra, Suman K and Gaur, H and Rupa, P K P and Pathak, L C (2006) Deposition of nanostructured Si–C–N superhard coatings by rf magnetron sputtering. Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures , 24 (3). pp. 1311-1317.

Mishra, Suman K and Gokuul, V and Paswan, S (2014) Alumina-titanium diboride in situ composite by self-propagating high-temperature synthesis (SHS) dynamic compaction: Effect of compaction pressure during synthesis. International Journal of Refractory Metals and Hard Materials, 43 (IF-1.764). pp. 19-24.

Mishra, Suman K and khusboo, and Sherbacov, V (2011) Fabrication of in-situ Ti–Si–C fine grained composite by the self propagating high temperature synthesis (SHS) process. International Journal of Refractory Metals and Hard Materials, 29 (2). pp. 209-213.

Mishra, Suman K and Mahanta, P and Sen, S and Pathak, L C (2012) Effect of Nitrogen on the Growth of Carbon Nitride Thin Films Deposited by RF Plasma Enhanced Chemical Vapor Deposition. Nanoscience and Nanotechnology Letters, 4 . pp. 90-94.

Mishra, Suman K and Mahato, P and Mahato, B and Pathak, L C (2013) Thermal stability and effect of substrate temperature of TiSiBC hard nanocomposite coatings on microstructure, mechanical, thermal behaviour deposited by magnetron sputtering. Applied Surface Science, 266(1 February) . pp. 209-213.

Mishra, Suman K and Pathak, L C (2005) Deposition of crystalline C–N film by arc evaporation process. Materials Letters, 59 (27). pp. 3481-3484.

Mishra, Suman K and Pathak, L C (2008) Effect of carbon and titanium carbide on sintering behaviour of zirconium diboride. Journal of Alloys and Compounds, 465 (1-2). pp. 547-555.

Mishra, Suman K and Pathak, L C (2002) Self-Propagating High-Temperature Synthesis(SHS) of Advanced High Temperature Materials. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Mishra, Suman K and Pathak, L C and Rao, Venkatesh (1997) Synthesis of submicron Ba-hexaferrite powder by a self-propagating chemical decomposition process. Materials Letters, 32 (2-3). pp. 137-141.

Mishra, Suman K and Ranganathan, S and Das, Swapan K and Das, Samar (1998) Investigations on precipitation characteristics in a high strength low alloy (HSLA) steel. Scripta Materialia, 39 (2). pp. 235-259.

Mishra, Suman K and Rupa, P K P and Das, Swapan K and Shcherbakov, V (2006) Effect of alumina diluent on the fabrication of in-situ Al2O3-Ti/ZrB2 composite by self propagating high temperature synthesis dynamic compaction. Metallurgical and Materials Transactions B, 37 (1). pp. 641-647.

Mishra, Suman K and Rupa, P K P and Das, Swapan K and Shcherbakov, V (2007) Effect of titanium diluent on the fabrication of Al2O3–ZrB2 composite by SHS dynamic compaction. Composites Science and Technology, 67 (7-8). pp. 1734-1739.

Mishra, Suman K and Rupa, P K P and Pathak, L C (2006) Nucleation and growth of DC magnetron sputtered titanium diboride thin films. Surface and Coatings Technology, 200 (12-13). pp. 4078-4081.

Mishra, Suman K and Rupa, P K P and Pathak, L C (2007) Surface and nanoindentation studies on nanocrystalline titanium diboride thin film deposited by magnetron sputtering. Thin Solid Films, 515 (17). pp. 6884-6889.

Mishra, Suman K and Shekhar, Chander and Rupa, P K P and Pathak, L C (2007) Effect of pressure and substrate temperature on the deposition of nano-structured silicon–carbon–nitride superhard coatings by magnetron sputtering. Thin Solid Films, 515 (11). pp. 4738-4744.

Mishra, Swati and Nayar, S (2014) Protein-polymer Matrix Mediated Synthesis of Silver Nanoparticles. Nanobiomedicine, 1(3) . pp. 1-5.

Mishra, T (2008) Anion supported TiO2–ZrO2 nanomaterial synthesized by reverse microemulsion technique as an efficient catalyst for solvent free nitration of halobenzene. Catalysis Communications, 9 . pp. 21-26.

Mishra, T and Hait, Jhumki and Aman, Noor and Gunjan, M K and Mahato, B and Jana, R K (2009) Corrigendum to “Surfactant mediated synthesis of spherical binary oxides photocatalyst with enhanced activity in visible light” [J. Colloid Interface Sci. 327 (2008) 377–383]. Journal of Colloid and Interface Science, 330 (1). 243- .

Mishra, T and Hait, Jhumki and Noor, Aman and Jana, R K and Chakravarty, S (2007) Effect of UV and visible light on photocatalytic reduction of lead and cadmium over titania based binary oxide materials. Journal of Colloid and Interface Science, 316 (1). pp. 80-84.

Mishra, T and Mohapatra, P and Parida, K M (2008) Synthesis, characterisation and catalytic evaluation of iron–manganese mixed oxide pillared clay for VOC decomposition reaction. Applied Catalysis B Environmental, 79 (http://dx.doi.org/10.1016/j.apcatb.2007.10.030). pp. 279-285.

Mishra, T and Parida, K M (2006) Effect of sulfate on the surface and catalytic properties of iron–chromium mixed oxide pillared clay. Journal of Colloid and Interface Science, 301 (2). pp. 554-559.

Mishra, T and Wang, Lei and Hahn, Robert and Schmuki, Patrik (2014) In-situ Cr doped anodized TiO2 nanotubes with increased photocurrent response. Electrochimica Acta, 132 (IF-4.086). pp. 410-415.

Mishra, Vidhyadhar and Garai, Subhadra (2013) Synthesis & Characterization of Biphasic Calcium Phosphate Nano composite as Bone Tissue Engineering. Training Report (TR). CSIR-NML, Jamshedpur. (Unpublished)

Misra, R A P (1958) Furnaces and Equipment used in the Manufacture and Heat Treatment of Alloy Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Misra, S B and Kamble, A and Yadav, S and Ranganathan, S (2015) Influence of charge segregation on specific aluminium consumption in production of ferro-titanium. Canadian Metallurgical Quarterly, 54(1) (IF-0.495). pp. 101-109.

Mitra, A (2001) Damage Assessment of Process Heater Tube by Magnetic Technique :A Case Study. In: UNSPECIFIED.

Mitra, A and Bhattamishra, A K and Chattoraj, I (1993) Magnetic-properties of hydrogenated amorphous fe-si-b fiber. Journal of Applied Physics, 73 (5). pp. 2443-2446.

Mitra, A and Chen, Z J and Jiles, D C (1995) Nondestructive magnetic measurements in weld and base metals of service exposed Cr-Mo steel. NDT & E International, 28 (1). pp. 29-33.

Mitra, A and Chen, Z J and Laabs, F and Jiles, D C (1997) Micromagnetic Barkhausen emissions in 2 center dot 25 wt% Cr-1wt% Mo steel subjected to creep. Philosophical magazine A-Physics of condensed matter structure defects and mechanical properties, 75 (3). pp. 847-859.

Mitra, A and De, P K and Bhattacharya, D K and Srivastava, P K and Jiles, D C (2004) Ferromagnetic properties of deformation-induced martensite transformation in AISI 304 stainless steel. Metallurgical and Materials Transactions A, 35 (2). pp. 599-605.

Mitra, A and Govindaraju, M R and Jiles, D C (1995) Influence of microstructure on micromagnetic barkhausen emissions in aisi-4140 steel. IEEE Transactions on Magnetics, 31 (6). pp. 4053-4055.

Mitra, A and Jiles, D C (1997) Magnetic Barkhausen emissions in as-quenched Fe-Si-B amorphous alloy. Journal of Magnetism and Magnetic Materials, 168 (1-2). pp. 169-176.

Mitra, A and Kim, H Y and Louzguine, D V and Nishiyama, N and Shen, B and Inoue, A (2003) Magnetic properties of melt-spun and annealed Fe62Co9.5Gd3.5Si10B15 alloy. Journal Of Physics D-Applied Physics, 36 (18). pp. 2234-2238.

Mitra, A and Kim, H Y and Louzguine, D V and Nishiyama, N and Shen, B and Inoue, A (2004) Structure and magnetic properties of amorphous and nanocrystalline Fe40Co40Cu0.5Zr9Al2Si4B4.5 alloys. Journal of Magnetism and Magnetic Materials, 278 (3). pp. 299-305.

Mitra, A and Kim, H Y and Shen, B L and Nishiyama, N and Inuue, A (2003) Crystallization and magnetic properties of Fe40Co40Cu0.5Al2Zr9Si4B4.5 and Fe62Co9.5Gd3.5Si10B15 amorphous alloys. Materials Transactions , 44 (8). pp. 1562-1565.

Mitra, A and Mohapatra, J N and Panda, A K and Das, A and Narasaiah, N and Jiles, D C (2006) Effect of Plastic Deformation on the Magnetic Properties 304 Stainless Steel During Tensile Loading. In: 9th European NDT Conference (ECNDT-2006), September 25-29, 2006, Berlin.

US2002000045033 (2003) Sensing device for the non-destructive evaluation of steel structures or components. US6617847.

Mitra, A and Palit Sagar, S and Chattoraj, I (1998) Crystallization and magnetic behaviour of Fe-Nb-Cu-Si-B alloys. Philosophical magazine b-physics of condensed matter statistical mechanics electronic optical and magnetic properties, 77 (6). pp. 1681-1691.

Mitra, A and Palit Sagar, S and Manik, N B (2002) Magnetic Barkhausen emission study in heat-treated Fe-Nb-Cu-Si-B alloy. IEEE Transactions on Magnetics, 38 (6). pp. 3669-3674.

Mitra, A and Panda, A K (2005) Development of nanocrystalline materials for soft-magnetic applications. Transactions of Indian Institute of Metals, 58 (6). pp. 981-991.

Mitra, A and Panda, A K (2008) Development of Ni-Mn-Ga based Ferromagnetic Shape Memory Alloy by Rapid Solidification Technique. Ferromagnetic Shape Memory Alloys Book Series: Advanced Materials Research , 52 . pp. 17-27.

Mitra, A and Panda, A K (2002) Giant Magneto-Impedance Behaviour in Ferro-Magnetic Materials. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Mitra, A and Panda, A K and Rao, Venkatesh (2001) Gaint magneto-impedance behaviour in amorphous and nanocrystalline soft magnetic materials. Journal of Metallurgy and materials Science, 43 (2). pp. 127-133.

Mitra, A and Panda, A K and Singh, Ratnakar and Rao, Venkatesh and Ramachandrarao, P (2003) Magnetic and structural behaviours of nanocrystalline Fe70.8Nb3.7Cu1Al2.7Mn0.7Si13.5B7.6 alloy. Philosophical Magazine, 83 (12). pp. 1495-1509.

Mitra, A and Panda, A K and Singh, S R and Ramachandrarao, P (2001) Preparation and characterization of Fe–Nb–Cu–Si–B-based nanocrystalline soft magnetic materials. Applied Surface Science, 182 (3-4). pp. 321-325.

Mitra, A and Rao, Venkatesh and Mohanty, O N and Ghatak, S K (1994) Magnetic-behavior of amorphous fe40ni40b20 alloy treated isothermally below crystallization temperature. Materials Transactions JIM, 35 (2). pp. 108-111.

Mitra, A and Rao, Venkatesh and Pramanik, S and Mohanty, O N (1992) Crystallization study of amorphous fe40ni40b20 by electrical-resistivity measurement. Journals of Materials Science, 27 (21). pp. 5863-5868.

Mitra, A and Rao, Venkatesh and Pramanik, S and Mohanty, O N (1992) Crystallization study of amorphous Fe40ni40b20 by electrical-resistivity measurement. Journal of Materials Science, 27 (21). pp. 5863-5868.

Mitra, A and Ravi Kumar, B and Mukhopadhyay, N K and Murthy, G V S and Das, Swapan K and Bhattacharya, D K (1996) Residual stress evaluation in service exposed shot peened spring by micromagnetic and XRD techniques. Trends in nde science and technology - proceedings of the 14th world conference on ndt (14th wcndt),, 1-5 ( ). pp. 879-882.

Mitra, A and Roy, Rajat K and Mahato, B and Panda, A K and Vlasak, G and Janickovic, D and Svec, S P (2011) Development of FeSiB/CoSiB Bilayered Melt-spun Ribbon by Melt-spinning Technique. Journal of Superconductivity and Novel Magnetism, 24(5) . pp. 611-615.

Mitra, A and Sipahi, L B and Govindaraju, M R and Jiles, D C and Ramanan, V R V (1996) Effects of tensile stress on magnetic Barkhausen emissions in amorphous Fe-Si-B alloy. Journal of Magnetism and Magnetic Materials, 153 (1-2). pp. 231-234.

Mitra, N (1994) Role of Indian Standards in Tailoring the properties of Wrought Steels. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Mittal, M and Nanda, T and Kumar, B Ravi and Singh, V (2017) Effect of inter-critical annealing parameters on ferrite recrystallization and austenite formation in DP 590 steel. Journal Materials and Manufacturing Processes , 32(11) (IF-2.274). 1231-1238 .

Mody, Russi (1981) Indian Steel in the Eighties. In: International Symposium on Modern Developments in Steel making, February 15, 1981, NML, Jamshedpur.

Mohanta, Ojaswini and Basumallick, A and Mitra, A and Panda, A K (2010) Enhancement in soft magnetic and ferromagnetic ordering behaviour through nanocrystallisation in Al substituted CoFeSiBNb alloys. Journal of Magnetism and Magnetic Materials, 322 (1). pp. 112-118.

Mohanta, Ojaswini and Ghosh, M and Mitra, A and Panda, A K (2009) Enhanced ferromagnetic ordering through nanocrystallization in cobalt incorporated FeSiBNb alloys. Journal Of Physics D-Applied Physics , 42 (6). 065007.

Mohanta, Ojaswini and Mitra, A and Chattoraj, I (2003) Reversible magnetic and mechanical response in hydrogenated amorphous Fe73.5Nb3Cu1Si13.5B9 alloys. Journal of Magnetism and Magnetic Materials, 266 (3). pp. 296-301.

Mohanta, Ojaswini and Singhbabu, Y N and Giri, S K and Dadhich, D and Das, N N and Sahu, Ranjan K (2013) Degradation of Congo red pollutants using microwave derived SrFe12O19: An efficient magnetic photocatalyst under visible light. Journal of Alloys and Compounds, 564 (IF-2.390). pp. 78-83.

Mohanty, Ashok and Patra, Trilochan and Dey, Joykrishna (2007) Salt-Induced Vesicle to Micelle Transition in Aqueous Solution of Sodium N-(4-n-Octyloxybenzoyl)-l-valinate. The Journal of Physical Chemistry B, 111 (25). pp. 7155-7159.

Mohanty, B and Jena, B K and Kandasamy, M and Dalai, N and Sahu, Ranjan K and Kadam, R M and Chakraborty, B and Jena, B (2020) The role of Se vacancies and Fe doping of nickel selenide in the water oxidation reaction. Sustainable Energy and Fuels, 4(6) (IF-5.503). pp. 3058-3065.

Mohanty, O N (1994) Residual Stresses in Heat Treatment. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Mohanty, O N (1994) Thermo Mechanical Treatment. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steel (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Mohapatra, B K and Nayak, B (2003) Mn-olivine from Gangpur Group of rocks, Orissa. Journal Of The Geological Society Of India, 61 (5). pp. 581-587.

Mohapatra, B K and Nayak, B (2005) Petrology of Mn carbonate–silicate rocks from the Gangpur Group, India. Journal of Asian Earth Sciences, 25 (5). pp. 773-780.

Mohapatra, J and Mishraz, D K and Singh, S K and Mahato, B and Mitra, A (2013) Synthesis of Nanocrystalline Co Doped ZnO by Chemical Route and Its Magnetic Properties. Nanoscience and Nanotechnology letters, 5/5 . pp. 563-567.

Mohapatra, J N and Bandopadhyay, N R and Gunjan, M K and Mitra, A (2010) Study of high-temperature ageing and creep on bainitic 5Cr–0.5Mo steel by magnetic NDE techniques. Journal of Magnetism and Magnetic Materials, 322 (6). pp. 589-595.

Mohapatra, J N and Panda, A K and Gunjan, M K and Mitra, A (2006) Evaluation of ageing behavior in modified 9Cr-1Mo steel by magnetic barkhausen emission technique. Journal of Metallurgy and Materials Science, 48 (3). pp. 167-171.

Mohapatra, J N and Panda, A K and Mitra, A (2009) Magnetic properties evaluation of ageing behaviour in water-quenched 5Cr-0.5Mo stee. Journal Of Physics D-Applied Physics , 42 (9). 095006.

Mohapatra, J N and Ray, Ashok K and Swaminathan, J and Mitra, A (2008) Creep behaviour study of virgin and service exposed 5Cr–0.5Mo steel using magnetic Barkhausen emissions technique. Journal of Magnetism and Magnetic Materials, 320 (18). pp. 2284-2290.

Mohapatra, J N and Swaminathan, J and Ghosh, M K and Mitra, A (2010) Magnetic Nondestructive Evaluation of Creep Behavior in Water-Quenched Modified 9Cr-1Mo Steel. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science, 41A (4). pp. 900-905.

Mohapatra, P and Mishra, T and Parida, K M (2006) Effect of microemulsion composition on textural and photocatalytic activity of titania nanomaterial. Applied Catalysis A: General, 310 . pp. 183-189.

Mondal, N and Pathak, P and Sengupta, P P and Roy, B C and Singh, A K and Kumar, S (2013) Reduction in Energy Consumption During Hot Rolling by Roll Bite Lubrication at Hot Strip Mill, Bokaro Steel Plant. In: proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Mondal, Sudipta and Pathak, L C and Venkateswarlu, K and Das, S K and Ray, Ajoy K (2002) Development and Characterization of Ag-Cu-Ti Alloys for Ceramic Brazing. In: Proceedings of the Indo-Malaysian Joint Workshop (WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Mucsi, G and Molnar, Zoltan and Kumar, Sanjay (2014) Geopolymerisation of Mechanically Activated Lignite and Brown Coal Fly Ash. Acta Physica Polonica A, 126 (IF-0.604). pp. 994-998.

Mucsi, Gabor and Kumar, Sanjay and Csoke, Barnabás and Kumar, Rakesh and Molnár, Zoltán and Rácz, Ádám and Mádai , Ferenc and Debreczeni , Ákos (2015) Control of geopolymer properties by grinding of land filled fly ash. International Journal of Mineral Processing, 143 (IF-1.31). pp. 50-58.

Mude, Rupla Naik and Panda, Soma Sekhara Balaji and Ghali, Venkata Subbarao and Muniyappa, Amarnath and Mulaveesala, Ravibabu (2011) Coded Excitation for Infrared Non-destructive Testing of Steel Materials. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries -NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Mukherjee, J K (1973) Sintered maraging alloys. International journal of powder metallurgy , 9 (2). pp. 95-100.

Mukherjee, J K (1971) Studies on the mechanical properties of Ni-Mn maraging steels. NML Technical Journal, 13 (3). pp. 65-68.

Mukherjee, J K and Banerjee, T (1969) Studies on nickel-manganese managing steels. NML Technical Journal, 11 (1). pp. 28-35.

Mukherjee, J K and Lahiri, A K and Banerjee, T (1968) Studies on the structural properties of rust from ancient iron. NML Technical Journal, 10 (1). pp. 25-29.

Mukherjee, K P and Khan, D K (1970) Some observations on manganese steel bimetallic couples from the point of view of cathodic protection. NML Technical Journal, 12 (3). pp. 78-82.

Mukherjee, K P and Lahiri, A K and Banerjee, T (1958) Effect of Low Alloy Additions on Corrosion of Steel in Different Atmospheres. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Mukherjee, R and Sahu, T and Sen, S and Sahu, Puspendu (2011) Structural and microstructural evolution due to increasing Co substitution in Ni1−xCoxFe2O4: An X-ray diffraction study using the Rietveld method. Materials Chemistry and Physics, 128 (3). pp. 365-370.

Mukherjee, S P and Kumar, Rajendra (1972) Metallographic studies of precipitation in iron-5% titanium steels. Metallography, 5 (6). pp. 479-484.

Mukherji, A N and Lahiri, A K (1972) Case of failure of stainless steel belt in alkali. NML Technical Journal, 14 (3). pp. 110-112.

Mukhopadhyay, Amartya and Basu, Bikramjit and Das Bakshi, Srimanta and Mishra, Suman K (2007) Pressureless sintering of ZrO2–ZrB2 composites: Microstructure and properties. International Journal of Refractory Metals and Hard Materials, 25 (2). pp. 179-188.

Mukhopadhyay, N K (1995) Basic Principles in Physical Metallurgy - II. In: Experimantal Techniques in Industrial Metallography[ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Mukhopadhyay, N K and Ali, F and Scudino, S and Khoshkhoo, M S and Stoica, M and Srivastava, V C and Uhlenwinkel, V and Vaughan, G and Suryanarayana, C and Eckert, J (2014) Inverse Hall Petch Like Mechanical Behaviour in Nanophase Al-Cu-Fe Quasicrystals: A New Phenomenon. Acta Physica Polonica A , 126(2) (IF-0.604). pp. 543-548.

Mukhopadhyay, N K and Ali, F and Srivastava, V C and Yadav, T P (2011) Strain-induced structural transformation of single-phase Al-Cu-Fe icosahedral quasicrystal during mechanical milling. Philosophical Magazine, 91 (19-21). pp. 2482-2490.

Mukhopadhyay, N K and Bhatt, Jatin and Pramanick, A K and Murty, B S and Paufler, P (2004) Synthesis of nanocrystalline/quasicrystalline Mg32(Al,Zn)49 by melt spinning and mechanical milling. Journal of Materials Science, 39 (16-17). pp. 5155-5159.

Mukhopadhyay, N K and Chattopadhyay, K and Ranganathan, S (1996) Ordering transformation in icosahedral quasicrystals and related crystalline phases. Bulletin of Materials Science, 19 (5). pp. 717-723.

Mukhopadhyay, N K and Das, Swapan K and Ravi Kumar, B and Ranganath, V R and Ghosh Chowdhury, S (1997) Premature failure of a leaf spring due to improper materials processing. Engineering Failure Analysis, 4 (3). pp. 161-170.

Mukhopadhyay, N K and Ghosh Chowdhury, S and Das, Goutam and Chattoraj, I and Das, S K and Bhattacharya, D K (1998) An investigation of the failure of low pressure steam turbine blades. Engineering Failure Analysis, 5 (3). pp. 181-193.

Mukhopadhyay, N K and Murthy, G V S (2002) An investigation on the transformation of the decagonal phase to a B2 phase in Al–Cu–Co alloy during mechanical milling. Journal of Alloys and Compounds, 342 (1-2). pp. 38-41.

Mukhopadhyay, N K and Murthy, G V S and Murty, B S and Weatherly, G C (2002) An investigation on the transformation of the decagonal phase to a B2 phase in Al-Cu-Co alloy during mechanical milling. Journal of Alloys and Compounds , 342 (1-2). pp. 38-41.

Mukhopadhyay, N K and Murthy, G V S and Murty, B S and Weatherly, G C (2002) An investigation on the transformation of the decagonal phase to a B2 phase in Al-Cu-Co alloy during mechanical milling. Journal of Alloys and Compounds, 342 (1-2). pp. 38-41.

Mukhopadhyay, N K and Sinha, Arvind (1997) Quasicrystals. Current Science, 73 (7). pp. 558-560.

Mukhopadhyay, N K and Uhlenwinkel, V and Srivastava, V C (2015) Synthesis and Characterization of Bulk Al-Cu-Fe Based Quasicrystals and Composites by Spray Forming. Journal of materials engineering and performance, 24(6) (IF-0.98). pp. 2172-2178.

Mukhopadhyay, N K and Weatherly, G C and Embury, J D (1995) Electron microscopy of decagonal phases in Al-Cu-Co-Si system. In: 5th International Conference on Quasicrystals, MAY 22-26, 1995, AVIGNON, FRANCE.

Mukhopadhyay, S (1999) Relaxation effects on thermally induced vibrations in a generalized thermoviscoelastic medium with a spherical cavity. Journal of thermal stresses, 22 (9). pp. 829-840.

Muller, Paul H and Oehler, Roland E (1961) Latest Developments in Aluminium Reduction. NML Technical Journal, 3 (1). pp. 29-36.

Munda, Parikshit and Das, Swapan K (2016) Failure analysis of an aeroengine compressor blade: A case study. IIM Metal News, 19(3) (NON-SCI). pp. 17-19.

Munda, Parikshit and Das, Swapan K and Husain, M M and Ghosh Chowdhury, S and Parida, N (2011) Failure Investigation of 1st Stage LPCR Blade Pertaining to Aero-Engine No. 8831010. Other (TMP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Munda, Parikshit and Hussain, M M and Singh, C V and Bagui, S (2020) Failure Analysis of a Steam Superheater Tube of a Vacuum Distillation Unit (VDU) in a Petrochemical Industry. Journal of Failure Analysis and Prevention, 20 (IF-0.800). pp. 1896-1906.

Munda, Parikshit and Kumar, S and Prakash, Amit and Husain, M M and Rajnikanth, V and Ghosh Chowdhury, S (2016) Failure Investigation of Boiler Water Wall Tubes of a Thermal Power Station. Journal of Failure Analysis and Prevention, 16(1) (IF 0.469). pp. 9-18.

Munda, Parikshit and Metya, Avijit Kumar (2011) Metallurgical Investigation on the Effect of BZL Welding of LPTR Blase Shrouded Tips of Aero Engines. In: International Seminar on Emerging Trends in Repair & Reclamation Technologies on Aero Engine Parts, Nov. 18 2011, Aeronautical Society of India, Chandigarh Branch.

Muralikrishna, A and Bagui, S and Mazumdar, D (2013) Modeling and Measurements of Intermixing Time in a Water Model of a Four Strand Steelmaking Tundish System. Transaction of Indian Institute of Metal, 66(3) . pp. 281-285.

Murmu, Laxmi and Ghosh Chowdhury, S and Gunjan, M K (2011) Project report on Microstructural Evolution of Ultra Fine Grained C-Mn Steel warm Rolling and Inter-Critical Annealed. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Murthy, D S R (1990) Microbially enhanced thiourea leaching of gold and silver from lead zinc-sulfide flotation tailings. Hydrometallurgy, 25 (1). pp. 51-60.

Murthy, D S R (1990) Microbially enhanced thiourea leaching of gold and silver from lead zinc-sulfide flotation tailings. Hydrometallurgy, 25 (1). pp. 51-60.

Murthy, D S R (1991) Some studies on the extraction of gold and silver from lead-zinc sulfide flotation tailings through non-cyanide leachants. Transaction of the Indian Institute of Metals, 44 (5). pp. 349-354.

Murthy, D S R and Khan, Z H and Akerkar, D D (1989) A chloridizing roast leach process for the extraction of copper and nickel from bulk sulfide concentrates. Transactions of The Indian Institute of Metals, 42 (2). pp. 149-154.

Murthy, D S R and Kumar, Vinay and Rao, K V (2003) Extraction of gold from an Indian low-grade refractory gold ore through physical beneficiation an thiourea leaching. Hydrometallurgy, 68 (1-3). pp. 125-130.

Murthy, D S R and Kumar, Vinay and Rao, K V (2003) low-grade refractory gold ore through physical beneficiation an thiourea leaching. Hydrometallurgy, 68(1-3) (IF-1.227). pp. 125-130.

Murthy, D S R and Prasad, P M (1996) Leaching of gold and silver from Miller Process dross through non-cyanide leachants. Hydrometallurgy, 42 (1). pp. 27-33.

Murthy, G V S and Anish, K and Jayakumar, T and Ghosh, R N (2009) Characterization Of Precipitation Behavior In Nimonic 263 By Ultrasonic Velocity Measurements. Review Of Progress In Quantitative Nondestructive Evaluation, Vols 28a And 28b , 1096 . pp. 1252-1258.

Murthy, G V S and Das, Goutam and Das, Swapan K and Praveen, Nikhat and Singh, S R (2011) Hardbanding failure in a heavy weight drill pipe. Engineering Failure Analysis, 18 (5). pp. 1395-1402.

Murthy, G V S and Das, Goutam and Das, Swapan K and Sridhar, G (2013) Microstructural investigation of defects in drill pipe. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 271-278.

Murthy, G V S and Das, Swapan K and Ravi Kumar, B (2014) Comprehensive Microstructural Characterization of γ′ in a Nimonic Alloy Using Ultrasonic Velocity Measurements. Metallography, Microstructure, and Analysis, 3(4) . pp. 328-335.

Murthy, G V S and Parveen, Nikhat and Nagesh, Ch R V S (2012) Processing of ilmenite (FeOTiO2) for value added products. In: XXVI International Mineral Processing Congress (IMPC) 2012 Proceedings, September, 2012, New Delhi.

Murthy, G V S and Ray, Ashok K and Minj, R K and Mukhopadhyay, N K (1999) Microhardness and Fracture Toughness Studies of Decagonal Quasicrystal in Al-Cu-Co System. Journal of Materials Science Letters, 18 (3). pp. 255-258.

Murthy, G V S and Sridhar, G (2013) Ultrasonic C-Scan evaluation of Ti-Alloy / Al brazed joint. Review of progress in quantitative nondestructive evaluation, 1511 . pp. 1120-1124.

Murthy, G V S and Sridhar, G and Kumar, Anish and Jayakumar, T (2009) Characterization of intermetallic precipitates in a Nimonic alloy by ultrasonic velocity measurements. Materials Characterization, 60 (3). pp. 234-239.

Murthy, SR and Subrahmanyam, N and Akerkar, D D (1981) Processing of bulk copper-nickel sulfide concentrates by electrothermal smelting and matte leaching. Transactions of the Indian Institute of metals, 34 (6). pp. 511-514.

Murty, B S and Kori, S A and Venkateswarlu, K and Bhat, R R and Chakraborty, M (1999) Manufacture of Al–Ti–B master alloys by the reaction of complex halide salts with molten aluminium. Journal of Materials Processing Technology, 89-90 . pp. 152-158.

Murugaiyan, Premkumar and Mitra, A and Jena, S M and Mahato, B and Ghosh, M and Roy, Rajat K and Panda, A K (2021) Grain refinement in Fe-rich FeSiB(P)NbCu nanocomposite alloys through P compositional modulation. Materials Letters, 295 (IF-3.204). p. 129852.

Murugananthan, M and Bhaskar Raju, G and Prabhakar, S (2004) Removal of sulfide, sulfate and sulfite ions by electro coagulation. Journal of Hazardous Materials, 109 (1-3). pp. 37-44.

Murugananthan, M and Bhaskar Raju, G and Prabhakar, S (2005) Removal of tannins and polyhydroxy phenols by electro-chemical techniques. JOURNAL OF CHEMICAL TECHNOLOGY AND BIOTECHNOLOGY , 80 (10). pp. 1188-1197.

Murugananthan, M and Bhaskar Raju, G and Prabhakar, S (2004) Separation of pollutants from tannery effluents by electro flotation. Separation and Purification Technology, 40 (1). pp. 69-75.

Murugananthan, M and Prabhakar, S and Bhaskar Raju, G (2004) Urban wastewater treatment by electroflotation. Fresenius Environmental Bulletin, 13 (6). pp. 519-523.

Murugesan, A P and Giribaskar, S and Gouthama, (2012) Metallographic studies on deformation microstructures of ECAE processed AA2014 aluminium alloy. Materials Science Forum, 702-703 . pp. 109-112.

Murugesan, A P and Rajnikanth, V and Mahato, B and Wegner, Matthias and Witte, M and Wilde, G and Ghosh Chowdhury, S (2017) Concurrent precipitation and associated texture evolution in AA 6082 alloy during high pressure torsion (HPT) processing. Materials Science and Engineering: A, 700 (IF-3.094). 487-494.

N

Na, Hyunjin and Yoo, Kyoungkeun and Jha, Manis K and Tabelin, Carlito Baltazar (2020) The Separation of Aluminum and Stainless‐Steel  Scraps Using Vibrating Mixed‐Size Ball Bed . Metals, 10 (IF-2.117). 868-1-868-10.

Nachankar, A V and Vaish, A K and Humane, M M and De, P K and Moghe, D V and Pathak, S U (2003) Bake hardening mechanism in steels. Journal of Metallurgy and materials Science, 45 (4). pp. 143-160.

Nag, P S and Mukherjee, K P (1979) Corrosion of steam header in the boiler plant-A case study. NML Technical Journal, 21 (3-4). pp. 25-29.

Nanda, T and Ravi Kumar, B and Bhinder, J (2016) Effect of Isothermal Annealing on Microstructural Morphology of Martensite in a Super-Martensitic Stainless Steel Subjected to Different Prior Conditions. Materials and Manufacturing Processes, 31(8) (IF 2.274). pp. 995-1003.

Nandy, Bikash and Chaudhury, Manoj Kumar and Pal, J and Bhattacharjee, D (2009) Sintering Characteristics of Indian Chrome Ore Fines. Metallurgical and Materials Transactions B, 40 (5). pp. 662-675.

Narang, S K (1979) A Unique anti-tarnish film by rhodium plating. In: All India seminar on precious metal plating, August 18, 1979, Bombay.

Narasaiah, N and Das, Swapan K and Parida, N (2011) Report on failure analysis of connecting rod bolt. Other (TMP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Narasaiah, N and Das, Swapan K and Sahu, J K and Das, Goutam and Sharma, S K and Parida, N (2011) Evaluation of Center Buffer Coupler (Knuckle). Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Narasaiah, N and Tarafder, S and Ray, K K (2006) Technique for direct measurement of effective fatigue threshold of materials. Materials Science and Technology, 22 (5). pp. 547-552.

Narasaiah, N and Tarafder, S and Sivaprasad, S (2010) Effect of crack depth on fracture toughness of 20MnMoNi55 pressure vessel steel. Materials Science and Engineering: A, 527 (9). pp. 2408-2411.

Narasimhan, B R V and Rao, D S and Kumar, Rakesh and Alex, T C and Ravi Kumar, B and Das, Swapan K and Srikanth, S and Mehrotra, S P (2006) Mechanochemical Activation of Zircon Sands - A Low Temperature route for Liberation of Zirconia (OLP-0014). Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Narayan, S P and Rao, V and Mohanty, O N (1991) Magnetic Property Improvement through Microstructural Modifications in a Commercial Grade HSLA Steel. NML Technical Journal, 33 (1-2). pp. 23-30.

Narayan, S P and Rao, Venkatesh and Das, S and Mohanty, O N (1990) Microstructural and magnetic studies on thermomechanically treated hsla steel. Journal of Magnetism and Magnetic Materials, 88 (1-2). pp. 71-78.

Narayan, S P and Rao, Venkatesh and Mohanty, O N (1991) Microstructural, mechanical and magnetic-properties of high-strength low-alloy steel. Journal of Magnetism and Magnetic Materials, 96 (1-3). pp. 137-144.

Nath, Niloy K and Assis, Paulo Santos and Chowdhury, Arunava (2013) Numerical Simulation Of Ingot And Concast Steel Reheating In Batch And Continuous Type Furnace To Optimize Energy Efficiency, Quality And Productivity. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, Decenber 16-18, 2013, CSIR-NML JSR.

Nath, S K and Kumar, Sanjay (2018) The potential use of silico-manganese slag into cementitious materials. In: Asia Steel International Conference 2018, 6-9 Feb., 2018, Mayfair Hotel, Bhubaneswar, India.

Nautiyal, Ashish and Upadhyay, T C (2013) Theoretical study of second order phase transition in hydrogen bonded order-disorder type pyroelectric cerium doped triglycine sulphate (Ce-TGS) Crystal. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 165-181.

Nayak, A K (1973) Thermal and quantitative thermal-analysis of Al-Zn alloys and determination of equilibrium diagram of binary-system. Journal of The Institute Of Metals, 101 (Nov-D). pp. 309-314.

Nayak, B and Das, Swapan K and Bhattacharyya, K K (2009) Baddeleyite (ZrO2) in manganese nodules of Central Indian Ocean Basin: An evidence for low temperature mobility of zirconium. Geochimica et Cosmochimica Acta, 73 (13). A933-A933.

Nayak, B and Das, Swapan K and Munda, Parikshit (2013) Biogenic signature and ultra microfossils in ferromanganese nodules of the Central Indian Ocean Basin. Journal of Asian Earth Sciences, Volume 73, 5 September 2013, Pages 296–305 (IF-2.379). pp. 296-305.

Nayak, B and Meyer, Franz Michael (2015) Tetrataenite in Terrestrial Rock. American Mineralogist, 100(1) (IF-2.059). pp. 209-214.

Nayak, B and Singh, A K and Upadhyay, A K and Bhattacharyya, K K (2009) A note on the characters of some Lower Gondwana coals of West Siang district in the Arunachal Himalaya and their trace element content. Journal of the Geological Society of India, 74 (3). pp. 395-401.

Nayak, B R and Mohapatra, B K (2005) Morpho-chemistry of hematite in manganese-rich formation of Gangpur Group, Orissa. Journal of the Geological Society of India, 66 (4). pp. 486-490.

Nayar, S and Guha, Avijit (2009) Waste utilization for the controlled synthesis of nanosized hydroxyapatite. Materials Science and Engineering: C, 29 (4). pp. 1326-1329.

Nayar, S and Mir, Aparna and Ashok, Aarti and Guha, Avijit and Sharma, Vikas (2010) Bovine Serum Albumin Binding and Drug Delivery Studies with PVA-Ferrofluid. Journal of Bionic Engineering, 7 (1). pp. 29-34.

Nayar, S and Palit Sagar, S and Guha, Avijit (2010) Non-destructive evaluation of mechanical properties of poly (vinyl) alcohol-hydroxyapatite nanocomposites. Journal of Materials Science-Materials in Medicine, 21 (4). pp. 1099-1102.

Nayar, S and Pramanick, A K and Sharma, Binay Kumar and Mishra, Rahul Kumar and Bansal, Satyendra Kumar and Prajapati, Amardeep and Sahu, K K and Das, Swapan K and Pathak, L C and Sinha, Arvind (2006) Hydroxyapatite coating on stainless steel pre-coated with bovine serum albumin at ambient conditions. Colloids and Surfaces B: Biointerfaces, 48 (2). pp. 183-187.

Nayar, S and Sinha, Arvind (2007) Biomimetic route to hybrid nano-Composite scaffold for tissue engineering. In: Nanoscience and Nanotechnology Initiative (NSTI), 21-23 February, 2007, Katriya Hotel & Towers, Hyderabad.

Nayar, S and Sinha, Arvind (2003) Protein induced morphosynthesis of calcium carbonate. Journal of Materials Science Letters, 22 (3). pp. 167-170.

Nayar, S and Sinha, Arvind (2004) Systematic evolution of a porous hydroxyapatite–poly(vinylalcohol)–gelatin composite. Colloids and Surfaces B: Biointerfaces, 35 (1). pp. 29-32.

Nayar, S and Sinha, Arvind and Das, Samar and Ramachandrarao, P (2001) In situ synthesis of nanosized cadmium sulfide using bovine serum albumin. Journal of Materials Science Letters, 20 (23). pp. 2099-2100.

Nayar, S and Sinha, M K and Basu, D and Sinha, Arvind (2006) Synthesis and sintering of biomimetic hydroxyapatite nanoparticles for biomedical applications. Journal of Materials Science: Materials in Medicine, 17 (11). pp. 1063-1068.

Nazri, Mobashshir Hameed and Ghosh Chowdhury, S (2013) Project Report on Reverse Austenitic Formation in 301 in Steel. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Neha, and Nayar, S (2012) Synthesis and Characterization of Nanomagnetic Hydroxy-patite using both Iron Salt Solution and Ferrofluid. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Nijhawan, B R (1959) Abstracts of Papers Presented at the Symposium on Iron and Steel Industry in India to be held at Jamshedpur. NML Technical Journal, 1 (1). pp. 1-28.

Nijhawan, B R (1958) Indian Alloy Steels for Engineering Industries. In: Symposium on Production Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R (1958) Micro-Metallurgy of Alloy Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R (1989) The present state and prospects of the world iron and steel industry. NML Technical Journal, 31 (1-4). pp. 3-11.

Nijhawan, B R (1966) Scope of research and development work on substitute alloys at the National Metallurgical Laboratory. NML Technical Journal, 8 (1). pp. 56-79.

Nijhawan, B R (1958) Tailor-Made Alloy Constructional Steels. In: Symposium on Production, Properties & Applictions of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R (1958) Temper-brittleness: Part I - Unalloyed Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R and Bucknall, E H (1958) Alloy Steel Industry in India - Historical. In: Symposium on Production, Properties & Applications of Alloy & Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R and Chatterjea, A B (1958) Substitution of Alloying Elements by Grain Size Control of Alloy Steels. In: Symposium on Production, Properties, and Applications of Alloy and special Steel, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R and Chatterjea, A B (1958) Temper-Brittleness: Part II- Alloy Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nijhawan, B R and Gupte, P K (1958) Manufacture in India of Ferro Alloys used in Alloy Steel Industry. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Nimbalkar, V M and Rao, B R K and Deshmukha, V P and Shah, A K and Marathe, K V (2011) Development reaction synthesis process of novel Al-alloys -TiB2 metal matrix composites by in-situ. Journal of Metallurgy and Materials Science, 53 (2). pp. 197-203.

Nistala, Harsha and Biswas, A and Sinha, Moni (2015) Heating index : estimation through numerical modeling of the sintering process and its relationship with sinter quality. Journal of Metallurgy and Materials Science, 57(2) . pp. 93-105.

O

O'Neill, Hugh (1958) The Application of Alloy and Special Steels in Railway Work. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Oellers, T and Raghavan, R and Chakraborty, J and Kirchlechner, C and Kostka, A and Liebscher, CH and Dehm, G and Ludwig, A (2018) Microstructure and mechanical properties in the thin film system Cu-Zr. Thin Solid Films, 645 (IF- 1.879). pp. 193-202.

Offner, Walter W (1958) Fabrication and Inspection of Alloy Steel Piping. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Ostwal, Chaitanya and Garg, Ayushi and Saptputre, Pranshu and Sasikumar, C (2013) Investigation of microwave heating in iron production. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Otten, Björn and Bhanja, Asoke (2013) Design, Erection and Implementation of a By-Product Plant at SAIL- IISCO Steel Plant in Burnpur, India1. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

P

Padmanabhan, K A and Basariya, M R (2009) Mesoscopic grain boundary sliding as the rate controlling process for high strain rate superplastic deformation. Materials Science and Engineering A, 527 (1-2). pp. 225-234.

Paetzke, N and Shakhverdova, I P and Levin, A A and Reibold, M and Kochmann, W and Paufler, P and Meyer, D C (2010) Nanoindentation behaviour and microstructure of several wootz-type steels. Journal of Metallurgy and Materials Science, 52 (1). pp. 47-65.

Pal, B C and Pillai, R M and Satyanarayana, K G (1998) Light Metal Matrix Composites - Present Status & Future Strategies. In: UNSPECIFIED.

Pal, J (2006) Thermodynamic analysis of nitrogen removal in EAF by DRI fines injection. Ironmaking & Steelmaking, 33 (6). pp. 466-470.

Pal, J and Ghorai, S and Bandyopadhyay, D and Ghosh, Sukomal (2015) Performance Assessment of Partially Pre-fused Synthetic Flux in Basic Oxygen Steel Making. Journal of Iron and Steel Research, International, 22 (IF-0.675). pp. 916-923.

Pal, J and Ghorai, S and Singh, D P and Upadhyay, A K and Ghosh, Sukomal and Ghosh, Dinabandhu and Bandyopadhyay, D (2010) Performance Assessment of CO2 Treated Fluxed Iron Oxide Pellets in Basic Oxygen Steel Making Process. ISIJ International, 50 (1). pp. 105-114.

Pal, J and Goswami, M C (2001) Simple mathematical models to control silicon, sulphur and manganese in hot metal during blast furnace operation. Journal of Metallurgy and materials Science, 43 (3). pp. 203-211.

Pal, S K and Manik, N B and Mitra, A (2006) Dependence of the driving current on the harmonic behavior of giant magneto-impedance voltage of Co-based amorphous wires. Journal of Magnetism and Magnetic Materials, 305 (1). pp. 240-246.

Pal, S K and Panda, A K and Mitra, A (2008) Effect of annealing on the second harmonic amplitude of Giant Magneto-Impedance (GMI) voltage of a Co–Fe–Si–B amorphous wire. Journal of Magnetism and Magnetic Materials, 320 (3-4). pp. 496-502.

Pal, S K and Panda, A K and Vazquez, M and Mitra, A (2006) The effect of magnetoelastic interaction on the GMI behaviour of Fe-, Co- and Co–Fe-based amorphous wires. Journal of Materials Processing Technology, 172 (2). pp. 182-187.

Palit Sagar, S (2008) Advanced ultrasonic for remaining life assessment of industrial components. In: Remaining Life Assessment of Aged Components in Thermal Power Plants and Petrochemical Industries, 2008, NML Jamshedpur 831007, India.

Palit Sagar, S and Chattoraj, I and Mitra, A (1999) The generation of magnetic bistability in annealed Fe-Si-B fibre by hydrogenation. Journal of Physics D-Applied Physics , 32 (5). pp. 541-545.

Palit Sagar, S and Chattoraj, I and Rao, Venkatesh and Ghatak, S K and Mitra, A (1997) Influence of hydrogen on the magnetic properties of amorphous Fe---Si---B fibres. Journal of Magnetism and Magnetic Materials, 166 (1-2). pp. 186-192.

Palit Sagar, S and Chattoraj, I and Rao, Venkatesh and Ghatak, S K and Mitra, A (1997) Influence of hydrogen on the magnetic properties of amorphous Fe-Si-B fibres (vol 166, pg 186, 1997). Journal of Magnetism and Magnetic Materials, 172 (3). pp. 322-323.

Palit Sagar, S and Das, S and Parida, N and Bhattacharya, D K (2006) Non-linear ultrasonic technique to assess fatigue damage in structural steel. Scripta Materialia, 55 (2). pp. 199-202.

Palit Sagar, S and Ghosh Chowdhury, S and Ravi Kumar, B and De, P K and Parida, N and Ghosh, R N (2006) Crystallographic Texture determination in deformed materials by Ultrasonic Technique. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Palit Sagar, S and Metya, Avijit Kumar and Ghosh, M and Sivaprasad, S (2011) Effect of microstructure on non-linear behavior of ultrasound during low cycle fatigue of pearlitic steels. Materials Science and Engineering A, 528 (6). pp. 2895-2898.

Palit Sagar, S and Metya, Avijit Kumar and Parida, N and Ghosh, R N (2008) Nonlinear ultrasonic to assess localized plastic deformation during high cycle fatigue. Review Of Progress In Quantitative Nondestructive Evaluation, Vol 27a And 27b Book Series: AIP Conference Proceedings, 975 . pp. 1260-1266.

Palit Sagar, S and Metya, Avijit Kumar and Prakash, Amit and Das, Arpan (2013) Development of Methodology to Analyse the Amplitude of Ultrasonic Signal from Shell/Core Interface of ICDP Rolls. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Palit Sagar, S and Murthy, G V S and Das, T K and Prakash, Amit (2011) Development of Ultrasonic Technique for Surface Crack Detection of Semi-HSS and HSS Rolls. Collaborative (CLP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Palit Sagar, S and Parida, N and Das, Samar and Dobmann, G and Bhattacharya, D K (2005) Magnetic Barkhausen emission to evaluate fatigue damage in a low carbon structural steel. International Journal of Fatigue, 27 (3). pp. 317-322.

Palit Sagar, S and Ravi Kumar, B and Dobmann, G and Bhattacharya, D K (2005) Magnetic characterization of cold rolled and aged AISI 304 stainless steel. NDT & E International, 38 (8). pp. 674-681.

Pan, L M and Ghosh, R N and MClean, M (1993) Extension of an anisotropic creep model to general high-temperature deformation of a single-crystal superalloy. Journal de Physique IV - Proceedings, 3 (C7). pp. 629-634.

Panda, A K and Basu, S and Mitra, A (2003) Demagnetisation effect and its correction on the measurement of magnetic hysteresis loop of melt-spun ribbons. Journal of Magnetism and Magnetic Materials, 261 (1-2). pp. 190-195.

Panda, A K and Chattoraj, I and Mitra, A (2001) Crystallization and magnetic properties of rapidly solidified Fe-Nb-M-Si-B (M=Cu, Mn, Pt). Materials Science and Engineering A, 304-306 . pp. 950-953.

Panda, A K and Chattoraj, I and Mitra, A (2000) Structural and soft magnetic properties of Fe73.5Nb3M1Si13.5B9 (M=Cu, Mn, Pt). Journal of Magnetism and Magnetic Materials, 222 (3). pp. 263-270.

Panda, A K and Das, Swapan K and De, P K and Mitra, A (2007) Sintering behaviour of magnetic bulk glassy cores obtained from Fe71Nb3.7Cu1Al3Mn0.8Si13.5B7 alloy powder. Journal of Materials Processing Technology, 184 (1-3). pp. 300-304.

Panda, A K and Dey, Sushmita and Roy, Rajat K and Singh, Satnam and Mitra, A (2015) Influence of phase transformation on interfacial activity and bend sensitivity of rapidly quenched Fe77.5Si7.5B15/Co72.5Si12.5B15 bilayered magnetostrictive ribbons. Journal of Magnetism and Magnetic Materials, 378 (IF-1.568). pp. 440-446.

Panda, A K and Ghosh, M and Kumar, Arvind and Mitra, A (2008) Magnetic transitions and structure of a NiMnGa ferromagnetic shape memory alloy prepared by melt spinning technique. Journal of Magnetism and Magnetic Materials, 320 (17). pp. 116-120.

Panda, A K and Ghosh, M and Kumar, Arvind and Singh, S R and Mitra, A (2007) Development of Ferromagnetic Shape Memory Alloys by Rapid Solidification Route. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Panda, A K and Kumar, Arvind and Ghosh, M and Mitra, A (2008) Development of Ni-Mn-Ga-based ferromagnetic shape memory alloy by rapid solidification route. Journal of Magnetism and Magnetic Materials, 320 (20). pp. 730-733.

Panda, A K and Kumari, Seema and Chattoraj, I and Ghosh, M and Mitra, A (2007) Electron transport properties of Co71−xFexCr7Si8B14 (x=0, 2, 3.2, 4, 6,8 and 12 at%) amorphous alloys during devitrification. Journal of Magnetism and Magnetic Materials, 308 (1). pp. 65-70.

Panda, A K and Manimaran, A and Basu, S and Mitra, A and Chattoraj, I (2005) Effect of structural evolution and surface morphological changes on the electrochemical response of an FeNbAlMnCuSiB alloy. Journal of Materials Science, 40 (17). pp. 4579-4584.

Panda, A K and Manimaran, A and Mitra, A and Basu, S (2004) AFM surface morphology and magnetic properties of nanocrystalline Fe71Nb3.7Cu1Al3Mn0.8Si13.5B7 ribbons. Applied Surface Science, 235 (4). pp. 475-486.

Panda, A K and Mitra, A and Chattoraj, I and Singh, S R and Ramachandrarao, P (2002) Development of Nanocrystalline FeNbCuSib based Alloy for Sensor Application. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedepur.

Panda, A K and Mohanta, Ojaswini and Basumallick, A and Mitra, A (2010) Low temperature magnetization behavior in Co36Fe36Si3Al1Nb4B20 (at%) nanostructured alloy. Journal of Magnetism and Magnetic Materials, 322 (23). pp. 3802-3806.

Panda, A K and Mohanta, Ojaswini and Ghosh, M and Mitra, A (2009) Development of Nanostructured CoFe-Based Alloys for High Temperature Magnetic Applications. Journal Of Nanoscience And Nanotechnology, 9 (9). pp. 5600-5603.

Panda, A K and Mohanta, Ojaswini and Mitra, A and Jiles, D C and Lo, C C H and Melikhov, Y (2007) Soft magnetic properties of a high temperature CoFeSiBNb nanocrystalline alloy. Journal of Magnetism and Magnetic Materials, 316 (2). pp. 886-889.

Panda, A K and Ravi Kumar, B and Basu, S and Mitra, A (2003) Crystallization and soft magnetic properties of rapidly solidified Fe73.5Nb3Cu1Si22.5−XBX (X=5, 9, 10, 11.25, 19) alloys. Journal of Magnetism and Magnetic Materials, 260 (1-2). pp. 70-77.

Panda, A K and Roy, Rajat K and Dey, Sushmita and Singh, S and Mitra, A (2013) Functional gradation through preferential crystallisation and interfacial activity in rapidly quenched Fe/Co-based bilayered ribbons for bend sensors. Journal of Applied Physics, 114/2 . 023909.

Panda, A K and Roy, S and Singh, S R and Rao, Venkatesh and Pramanik, S and Chattoraj, I and Mitra, A and Ramachandrarao, P (2001) Effect of quenching rate on the properties of melt-spun FeNbCuSIB ribbons. Materials Science and Engineering A, 304-306 . pp. 457-461.

Panda, A K and Singh, S and Das, Swapan K and Mitra, A and Koblischka, M and Jamieson, B and Roy, Subrata (2009) Effect of magnetizing field on the martensitic transformations in a melt spun NiMnGa alloy. Journal Of Physics D-Applied Physics , 42 (24). p. 245004.

Panda, A K and Singh, Satnam and Roy, Rajat K and Ghosh, M and Mitra, A (2011) Effect of Mn incorporation for Ni on the properties of melt spun off-stoichiometric compositions of NiMnGa alloys. Journal of Magnetism and Magnetic Materials, 323 (9). pp. 1161-1169.

Panda, E and Mazumdar, D and Mehrotra, S P (2006) Mathematical modeling of particle segregation during centrifugal casting of metal matrix composites. Metallurgical And Materials Transactions A-Physical Metallurgy And Materials Science , 37 A (5). pp. 1675-1687.

Panda, P K and Lahiri, A K and Banerjee, T (1971) Pressure dependence of oxidation rate of Cu-40 Mn alloy at 800°C. Scripta Metallurgica, 5 (8). pp. 677-679.

Panda, P K and Mariappan, L and Kannan, T S (1998) Preparation of Al2O3 - SiC In-Situ Composite Powder Mixtures by Carbothermal Reduction of Kaolinite. In: UNSPECIFIED.

Pande, A M and Gupta, K N and Altekar, V A (1982) Single cell extraction of zinc and manganese dioxide from zinc sulphide concentrate and manganese ores. Hydrometallurgy, 9 (1). pp. 57-68.

Pande, A M and Gupta, K N and Altekar, V A (1982) Single cell extraction of zinc and manganese-dioxide from zinc-sulfide concentrate and manganese ores. Hydrometallurgy, 9 (1). pp. 57-68.

Pandey, A K and Debnath, K K and Setua, D K and Mathur, G N and Chandra, R (1998) Butyl Rubber-Nylon Composites with Improved Flame Retardancy & Gas Impermeability. In: UNSPECIFIED.

Pandey, B D and Bagchi, D and Kumar, Vinay (1994) Coextraction - selective stripping for the recovery of nickel and copper from the leach liquor of ocean nodules. Canadian Journal of Chemical Engineering , 72 (4). pp. 631-636.

Pandey, B D and Cote, G and Bauer, D (1996) Extraction of chromium(III) from spent tanning baths. Hydrometallurgy, 40 (3). pp. 343-357.

Pandey, B D and Kumar, Vinay (1991) Extraction of copper and nickel from ammoniacal leach liquor of Indian Ocean sea nodules. Hydrometallurgy, 26 (1). pp. 35-45.

Pandey, J L and Banerjee, M K (1998) Concrete corrosion and control practices - an overview. Anti-corrosion methods and materials, 45 (1). 5 - .

Pandey, J L and Banerjee, M K (1998) Energy conservation with the use of solar selective coatings. Anti-corrosion methods and materials, 45 (1). 16- .

Pandey, J L and Banerjee, M K (1997) High-temperature-resistant (slurry-based) coatings. Anti-corrosion methods and materials, 44 (6). 368- .

Pandey, J L and Prakash, S and Mehta, M L (1990) Effects of varying the zirconium concentration and 1 wt-percent-y on high-temperature oxidation of fe-15wt-percent-Cr-4wt-percent-Al alloy under isothermal and cyclic conditions. Journal of The Less-Common Metals, 159 (1-2). pp. 23-34.

Pandey, J L and Prakash, S and Mehta, M L (1990) Effects of varying the zirconium concentration and 1 wt.% Y on high temperature oxidation of Fe-15wt.%Cr-4wt.%Al alloy under isothermal and cyclic conditions. Journal of the Less Common Metals, 159 ( ). pp. 23-24.

Pandey, J L and Rao, T B and Singh, S and Singh, S K (1998) Approaches to ISO certification - Paint manufacturing industry. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Pandey, J L and Singh, Inder and Singh, M N (1997) Electrochemical corrosion behaviour of heat-treated AISI 304 austenitic stainless steel in inorganic acid mixture. Anti-corrosion methods and materials, 44 (1). 6- .

Pandey, L P and Ghose, A and Dasgupta, P (1978) Determination of chromium in low-alloy steels by atomic-absorption spectrophotometry. Talanta, 25 (8). pp. 482-483.

Pandey, L P and Gupta, K K and Jha, S N and Dasgupta, P and Chatterjee, N N (1988) Use of lanthanum for eliminating the interferent effect of aluminum in the determination of magnesium in aluminum-alloys by aas. Fresenius zeitschrift fur analytische chemie, 329 (7). p. 795.

Pandey, P K and Dash, R R and Singh, M P (1998) Studies on the In-Situ Formation of AI2O3 - SiC Ceramic Matrix Composite from Tata Steel Colliery over Burden. In: UNSPECIFIED.

Pandey, R S (2015) Mathematical modeling of iron ore pelletization in a straight-grate induration process. Journal of Metallurgy and Materials Science, 57(3) . pp. 179-186.

Pandit, S (1994) Quality Aspects of Special Forgings of Low Alloy Steels. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Panindre, Anup M and Ranjan, Nitish and Sahu, Rina (2014) Reclaiming iron from solid wastes via Romelt process. Journal of Metallurgy and Materials Science, 56(3) (NON-SCI). pp. 163-172.

Panna, Praveen Kumar and Roy, Rajat K (2012) Study of Microstructural Behaviour of Medium Carbon Steel by Magnetic NDE Technique. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Pansari, Avinaw and Palit Sagar, S (2013) Development of an Online IR-Thermography based Non-Invasive Technique to Detect and Estimate Iron in Galvannealed IF Steel Sheet. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Paranjpe, V G and Visvanathan, S (1958) Low-Alloy High-Strength Steels. In: Symposium on Production, Properties & Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Parashar, S K S and Basu, D K and Banerjee, M K (2003) Coating failure analysis using stress intensity factor and fracture energy. Journal of Metallurgy and materials Science, 45 (1). pp. 11-17.

Parchur, A K and Prasad, A I and Rai, S B and Tewari, R and Sahu, Ranjan K and Okram, G S and Singh, R A and Ningthoujam, R S (2012) Observation of intermediate bands in Eu3+ doped YPO4 host: Li+ ion effect and blue to pink light emitter. AIP Advances, 2 (3). 032119-1.

Parida, K M and Mishra, T and Das, D (1999) Thermal transformation of trinuclear FeIII/ acetato complex intercalated montmorillonite. Applied Clay Science, 15 . pp. 463-475.

Parida, N (2008) Condition monitoring of pressure vessels and storage tanks by acoustic emission technique. In: UNSPECIFIED.

Parida, N (2009) Non Destructive Testing and Evaluation. In: A Continuing Education Course on Metallurgy for Engineers, December 14-16, 2009, NML, Jamshedpur.

Parida, N (1991) Reliability and life estimation from component fatigue failures below the go-no-go fatigue life limit. Journal of testing and evaluation, 19 (6). pp. 450-453.

Parida, N and Das, Swapan K and Gope, P C and Mohanty, O N (1990) Confidence, and sample-size in fatigue testing. Journal of Testing and Evaluation, 18 (6). pp. 385-389.

Parida, N and Das, Swapan K and Gope, P C and Mohanty, O N (1990) Probability, confidence, and sample-size in fatigue testing. Journal of Testing and Evaluation, 18 (6). pp. 385-389.

Parida, N and Pani, B B and Ravi Kumar, B (1997) Acoustic emission assisted compaction studies on iron, iron-aluminium and iron-cast iron powders. Scripta Materialia, 37 (11). pp. 1659-1663.

Parida, N and Ravi Kumar, B and Bhattacharya, D M (1998) Fatigue damage assessment and detection of onset of crack initiation by x-ray diffraction. Transactions of the Indian Institute of Metals, 51 (2-3). pp. 175-177.

Parida, N and Ravi Kumar, B and Das, Goutam and Murthy, S G N and Bhattacharya, D K (1996) Monitoring the hydrotesting of a new pressure vessel by means of acoustic emission. Trends in nde science and technology - proceedings of the 14th world conference on ndt (14th wcndt),, 1-5 ( ). pp. 2423-2426.

Parida, N and Sivaprasad, S and Tarafder, S and Ranganath, V R and Bhattacharya, D K (1999) Acoustic emission: A novel technique for the study of fracture micro-mechanisms. Journal of non destructive evaluation, 19 (3). pp. 51-55.

Parijat, Prateek and Bhattacharya, Maitreyee (2013) Process for the Recovery of Tungsten by Oxidative Roasting and Leaching. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Parmar, Kavita and Bhattacharjee, S (2014) Studies on Pb(II) and Cd(II) adsorption by Fe(II) and Fe(III) silicate precipitation tubes in aqueous medium. Journal of Metallurgy and Materials Science, 56(2) (NON-SCI). pp. 125-135.

Parmar, Kavita and Chaturvedi, Hema T and Akhtar, Md Wasi and Chakravarty, S and Das, S K and Pramanick, A K and Ghosh, M and Panda, A K and Bandopadhyay, N R and Bhattacharjee, S (2009) Characterization of cobalt precipitation tube synthesized through “silica garden” route. Materials Characterization, 60 (8). pp. 863-868.

Parmar, Kavita and Chongder, Durbadal and Bandyopadhyay, N R and Bhattacharjee, S (2012) Synthesis and characterization of Fe(II)-silicate precipitation tube (FeIISPT) as a heavy metal adsorbent and its comparison with Fe(III)-silicate precipitation tube (FeIIISPT). Journal of Metallurgy and Materials Science, 54(3) . pp. 269-277.

Parveen, Nikhat and Murthy, G V S (2013) Characterization of electrical behavior in modified ilmenite. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 195-200.

Parveen, Nikhat and Murthy, G V S (2011) Determination of elastic modulus in a nickel alloy from ultrasonic measurements. Bulletin of Materials Science, 34 (2). pp. 321-324.

Pathak, Arvind and Kumar, Sanjay and Jha, Vinay Kumar (2014) Development of Building Material from Geopolymerization of Construction and Demolition Waste (CDW). Transactions of the Indian Ceramic Society, 73(2) (IF-0.233). pp. 133-137.

Pathak, B N and Mishra, M N and Sahoo, K L (2012) Solidification behavior, microstructure and mechanical properties of Al-(1 to 5)Fe-1V-1Si alloys. Journal of Metallurgy and Materials Science, 54(4) . pp. 291-298.

Pathak, B N and Sahoo, K L and Mishra, Madhawanand (2013) Effect of Machining Parameters on Cutting Forces and Surface Roughness in Al-(1-2) Fe-1V-1Si Alloys. Materials and Manufacturing Processes, 28(4) . pp. 463-469.

Pathak, L C (2004) Fabrication and sintering characteristics of doctor blade YBCO-Ag tapes. Ceramics International, 30 (3). pp. 417-427.

Pathak, L C (2002) Synthesis of Nano-Crystalline Ceramic powders by Chemical Process. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Pathak, L C and Bandyopadhyay, D and Srikanth, S and Das, Swapan K (2001) Effect of heating rates on the synthesis of Al2O3–SiC composites by the self-propagating high-temperature synthesis (SHS) technique. Journal of the American Ceramic Society, 84 (5). pp. 915-920.

Pathak, L C and Mishra, Suman K (2005) A review on the synthesis of Y-Ba-Cu-oxide powder. SUPERCONDUCTOR SCIENCE & TECHNOLOGY, 18 (9). R 67-R 89.

Pathak, L C and Mishra, Suman K and Bhattacharya, D and Chopra, K L (1997) A comparative study of YBCO powders prepared by different processes. Journal of Materials Science Letters, 16 (14). pp. 1208-1211.

Pathak, L C and Mishra, Suman K and Bhattacharya, D and Chopra, K L (1999) Degradation of BPSCCO superconductors during processing. Journal of Materials Science, 34 (7). pp. 1619-1624.

Pathak, L C and Mishra, Suman K and Bhattacharyya, D and Chopra, K L (1999) Sintering characteristics of Y-Ba-Cu-oxide-Ag-x superconductors. Journal of Materials Research, 14 (11). pp. 4148-4156.

Pathak, L C and Mishra, Suman K and Das, Swapan K and Bhattacharya, D (2001) Effect of sintering atmosphere on the weak-link behaviour of YBCO superconductors. Physica C: Superconductivity, 351 (3). pp. 295-300.

Pathak, L C and Mishra, Suman K and Srikanth, S (1998) Effect of Silver on the Sintering Characteristics of High T Ceramic Superconductors. In: Proceedings of Composite Materials, March, 1998, NML Jamshedpur, India.

Pathak, L C and Mishra, Suman K and Srikanth, S (2002) Sintering characteristics of Y-Ba-Cu oxide-Ag-x superconductors under argon atmosphere. Journal of Materials Research, 17 (4). pp. 895-900.

Pathak, L C and Ray, Ashok K and Das, Samar (1999) Carbothermal synthesis of nanocrystalline aluminum nitride powders. Journal of the American Ceramic Society, 82 (1). pp. 257-260.

Pathak, L C and Singh, T B and Das, S and Verma, A K and Ramachandrarao, P (2002) Effect of pH on the combustion synthesis of nano-crystalline alumina powder. Materials Letters, 57 (2). pp. 380-385.

Pathak, L C and Singh, T B and Das, Swapan K (2004) Role of templating agents on the growth morphology of AIPO4. Journal of Materials Science, 39 (12). pp. 4069-4071.

Pathak, P N and Rafiuddin, S (1998) Recovery of barite from complex sulphide ores. Metals Materials and Processes, 10 (2). pp. 189-191.

Pati, B B and Chatterjee, P and Singh, T B and Singh, D D N (1990) Effect of propargyl alcohol on corrosion and hydrogenation of steel in hydrochloric-acid solution. Corrosion, 46 (5). pp. 354-359.

Patil, Deepak C and Kori, S A and Venkateswarlu, K and Das, Goutam and Alhajeri, S N and Langdon, T G (2013) Using ball indentation to determine the mechanical properties of an Al-7475 alloy processed by high-pressure torsion. Journal of Materials Science, 48(13) (IF-2.163). pp. 4773-4779.

Patil, M R and Ravi, B P and Krishna, S J G and Kumar, P S and Rudrappa, C and Gundewar, C S (2013) Processing Studies on Iron Ore Tailings Sample For Pelletisation Plant From Barbil Region, Orissa. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Patil, Pravin J and Devi, Kadambini and Rane, D M and Sen, Amit and Sonawane, A U and Hussein, S A (2011) Application of Radiation Sources in Steel Industry in India. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Patra, S and Hasan, Sk. Md. and Narasaiah, N and Chakrabarti, D (2012) Effect of bimodaldistribution in ferritegrainsizes on the tensileproperties of low-carbonsteels. Materials Science and Engineering A, 538 (15). pp. 145-155.

Pattanayak, S and Dey, Swati and Chatterjee, S and Ghosh Chowdhury, S and Datta, S (2015) Computational intelligence based designing of microalloyed pipeline steel. Computational Materials Science, 104 (IF-1.879). pp. 60-68.

Patty, B B (1991) Corrosion inhibition of steel in methanol-HCl by tetrabutylammonium iodide. Indian Journal of Technology, 29 (12). pp. 595-598.

Patty, B B and Banerjee, M K (1991) Effect of ph and chloride-ions on the dissolution of steel in methanol. Indian Journal of Technology, 29 (1). pp. 35-39.

Patty, B B and Das, C R and Singh, D D N (1995) Role of hydrogen promoters on corrosion and hydrogenation of mild-steel in aqueous and methanolic hydrochloric-acid solutions. Corrosion , 51 (7). pp. 537-543.

Patty, B B and Singh, D D N (1992) Solvents role on hcl-induced corrosion of mild-steel - its control by propargyl alcohol and metal-cations. Corrosion, 48 (6). pp. 442-446.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, Mita and Tarafder, S (2010) Simulation of cyclic plastic deformation response in SA333 C–Mn steel by a kinematic hardening model. Computational Materials Science, 48 (3). pp. 662-671.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2010) Cyclic plastic deformation and cyclic hardening/softening behavior in 304LN stainless steel. Theoretical and Applied Fracture Mechanics, 54 (1). pp. 63-70.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2011) Cyclic plastic deformation and damage in 304LN stainless steel. Materials Science and Engineering A, 528 (15). pp. 4873-4882.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2011) Cyclic plastic deformation behavior in SA333 Gr. 6 C-Mn steel. Materials Science and Engineering A, 528 (24). pp. 7341-7349.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2011) Key issues in cyclic plastic deformation: experimentation. Mechanics of Materials, 43 (11). pp. 705-720.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2010) Ratcheting and low cycle fatigue behavior of SA333 steel and their life prediction. Journal of Nuclear Materials, 401 . pp. 17-24.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2010) True stress control asymmetric cyclic plastic behavior in SA333 C–Mn steel. International Journal of Pressure Vessels and Piping, 87 (8). pp. 440-446.

Paul, Surajit Kumar and Sivaprasad, S and Dhar, S and Tarafder, S (2012) True stress-controlled ratcheting behavior of 304LN stainless steel. Journal of Materials Science, 47 (11). pp. 4660-4672.

Perrin, R and Greffe, A (1962) Some Applications of Rapid Metallurgy to the Manufacture of Ferro Alloys. NML Technical Journal, 4 (1). pp. 20-25.

Peter, Nicolas J and Duarte, Maria J and Liebscher, Christian H and Srivastava, V C and Uhlenwinkel, Volker and Jägle, Eric A and Dehm, Gerhard (2020) Early stage phase separation of AlCoCr0.75Cu0.5FeNi high-entropy powder at the nanoscale. Journal of Alloys and Compounds, 820 . p. 153149.

Peyton, A J and Stefani, F and Eckert, S and Timmel, K and Wondrak, T and Gerbeth, G (2013) Electromagnetic Induction Tomography for Monitoring Liquid Metal Flow During Continuous Casting. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Phani Kiran, K S and Sivalingaraju, B and Reddy, Siddaling and Venkateswarlu, Y and Marutiram, K and Naha, T K (2013) Use of Petroleum Coke as an Additive in Metallurgical Coke Making. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Phuong, To Duy and Bach, Tran Ngoc and Park, Y H and Lee, Z H (2006) Effect of nitrogen and rare earth metals in duplex stain-less steel on transformation of ferrite-austenite structure. Journal of Metallurgy and Materials Science, 48 (1). pp. 13-21.

Phuong, To Duy and Duyen, Do Thi (2012) Effect of heat treatment on microstructure and hardness of high silicon aluminium alloys. Journal of Metallurgy and Materials Science, 54(2) . pp. 111-117.

Phuong, To Duy and Duyen, Do Thi and Tuan, Le Minh and Thang, Pham Duc and Xuong, Nguyen Khac (2011) Studies on Ni-Cr-Mo-Ti dental cast superalloys. Journal of Metallurgy and Materials Science, 53 (3). pp. 217-224.

Pillai, K C and Narayan, R (1978) Inhibition of corrosion of iron in acids by thiourea and derivatives. Journal of The Electrochemical Society (JES), 125 (9). pp. 1393-1397.

Pillai, KC and Narain, Raj (1977) Inhibition of corrosion of iron in acids by thiourea and derivatives. Journal of the electrochemical society (JES), 124 (3). C94-C94.

Poddar, D and Ravi Kumar, B (2021) Effect of thermo-elasto-plastic strain on the mechanism of twin-free microstructure formation in the stainless steel. Materials Characterization, 171 . p. 110742.

Poddar, Palash and Das, Arpan and Sahoo, K L (2014) Dry Sliding Wear Characteristics of Gravity Die-Cast Magnesium Alloys. Metallurgical and Materials Transactions A , 45A(4) (IF-1.730). pp. 2270-2283.

Poddar, Palash and Gupta, Savita and Sahoo, K L (2017) Magnesium-tin based composites processed through stir casting. Journal of Metallurgy and Materials Science, 59(4) . pp. 153-161.

Poddar, Palash and Mukherjee, Surojit and Sahoo, K L (2009) The Microstructure and Mechanical Properties of SiC Reinforced Magnesium Based Composites by Rheocasting Process. Journal of Materials Engineering and Performance, 18 (7). pp. 849-855.

Poddar, Palash and Sahoo, K L (2012) Microstructure and mechanical properties of conventional cast and rheocast Mg-Sn based alloys. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 556 (IF-2.003). pp. 891-905.

Poddar, Palash and Sahoo, K L and Mukherjee, S and Ray, Ashok K (2012) Creep behaviour of Mg-8% Sn and Mg-8% Sn-3% Al-1% Si alloys. Materials Science and Engineering A, 545 . pp. 103-110.

Prabhakar, S and Bhaskar Raju, G (1998) Amenability of column flotation for lead-zinc beneficiation - A case study. Metals Materials and Processes, 10 (2). pp. 109-118.

Prabhakar, S and Bhaskar Raju, G and Sankaran, C (1994) Quality improvement of copper concentrates by column flotation. Transactions of the indian institute of metals, 47 (2-3). pp. 89-101.

Prabhakar, S and Bhaskar Raju, G and Subba Rao, S (2006) Beneficiation of sillimanite by column flotation - a pilot scale study. International Journal of Mineral Processing, 81 (3). pp. 159-165.

Prabhakar, S and Goswami, M C and Mahapatra, A K S and Ghosh, K C and Das, S K and Sinha, A N and Mishra, K K (2000) Morphology and reduction kinetics of fluxed iron ore pellets. Ironmaking & Steelmaking, 27 (3). pp. 194-201.

Prabhakar, S and Goswami, M C and Mahapatra, A K S and Ghosh, K C and Das, Swapan K and Sinha, A N and Mishra, K K (2000) Morphology and reduction kinetics of fluxed iron ore pellets. Ironmaking & Steelmaking, 27 (3). pp. 194-201.

Prabhakar, S and Gupta, K N and Ray, H S and Sarangi, R and Bhole, A D and Sarkar, S B (1989) Studies on coal reactivity employing moving bed boat technique. Transactions of The Indian Institute of Metals, 42 (3). pp. 241-253.

Prabhakar, S and Rao, K Hanumantha and Fodor, W (2005) Dissolution of wollastonite and its flotation and surface interactions with tallow-1,3-diaminopropane (duomeen T. Minerals Engineering, 18 (7). pp. 691-700.

Prabhakar, S and Ray, H S and Gupta, K N (1986) Bench-scale experiment to simulate vertical retort process for production of direct reduced iron. Ironmaking & steelmaking, 13 (2). pp. 76-79.

Prabhu, N S and Joseyphus, J and Sankara Narayanan, T S N and Ravi Kumar, B and Mitra, A and Panda, A K (2012) Residual Stress Analysis in Surface Mechanical Attrition Treated (SMAT) Iron and Steel Component Materials by Magnetic Barkhausen Emission Technique. IEEE Transactions on Magnetics, 48(12) (IF-1.363). pp. 4713-4717.

Pradhan, B and Chakraborty, D (1998) Delamination Initiation at the Interface of Broken & Continuous Plies In FRP Composite Laminates. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 206-213.

Pradhan, B and Kumar, N Venu and Rao, N S (1998) Modelling of Multiple Transverse Cracks In Angle - Ply Laminates. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 224-232.

Pradhan, B and Kumar, Sanjay (2000) Finite element analysis of low-velocity impact damage in composite laminates. Journal of Reinforced Plastics and Composites, 19 (4). pp. 322-339.

Pradhan, S K and Dwarakadasa, E S (1998) Processing & Characterization of UHMWPE-CSP (Coconut Shell Powder) Composite. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 283-287.

Prakash, B (1997) Ancient Iron Making in India. In: Iron and Steel Heritage of India, November, 1997, IIM & Tata Steel, Jamshedpur.

Prakash, Hari (1987) Energy-dispersive x-ray-analysis of binary and quaternary systems. Indian journal of chemistry section a-inorganic bio-inorganic physical theoretical & analytical chemistry, 26 (5). pp. 440-444.

Prakash, Hari (1986) Mocvd alxga1-xas solar-cells. Progress in crystal growth and characterization of materials, 12 (1-4). pp. 257-264.

Prakash, Hari (1986) MOCVD AlxGa1−xAs solar cells. Progress in Crystal Growth and Characterization, 12 (1-4). pp. 257-264.

Prakash, S (1994) Nonisothermal kinetics of iron-ore reduction. Ironmaking & Steelmaking, 21 (3). pp. 237-243.

Prakash, S (1994) On dynamic nonisothermal techniques for characterization of ironmaking raw-materials. Scandinavian journal of metallurgy, 23 (5-6). pp. 236-243.

Prakash, S (1996) Reduction and sintering of fluxed iron ore pellets - A comprehensive review. Journal of the south african institute of mining and metallurgy, 96 (1). pp. 3-16.

Prakash, S and Dhindaw, B K and Sengupta, S (1997) Smelting reduction of prereduced iron ore. Smelting reduction of prereduced iron ore, 24 (6). pp. 468-475.

Prakash, S and Mukherjee, K and Mehrotra, S P (2005) Cold model study of metal droplet descent through fluids including a treatment of the non-Newtonian behaviour as exhibited by molten stag system. Ironmaking & Steelmaking, 32 (6). pp. 494-502.

Prakash, S and Ray, H S (1991) Moving-bed studies on reaction behavior of iron-ore and coal char mixtures in gasifying agents. Fuel, 70 (1). pp. 17-23.

Prakash, S and Ray, H S (1990) Prediction of reduction kinetics of iron-ore under fluctuating temperature conditions. ISIJ International, 30 (3). pp. 183-191.

Prakash, S and Ray, H S and Gupta, K K (1987) Use of the moving bed technique for the assessment of reducibility of iron ores and reactivity of solid reductants. Reactivity of Solids, 4 (3). pp. 215-226.

Prakash, S and Ray, H S and Gupta, K N (1992) Use of kinetic plots for relative assessment of reactor throughput and energy-consumption. Journal of Thermal Analysis, 38 (11). pp. 2467-2482.

Prakash, S and Ray, H S and Gupta , K N (1992) Use of kinetic plots for relative assessment of reactor throughput and energy-consumption. Journal of Thermal Analysis and Calorimetry, 38 (11). pp. 2467-2482.

Prakash, Ved and Pool, M J (1981) Effect of impurities (graphite) on the high-temperature creep-properties of NIAL. Journal of Materials Science, 16 (9). pp. 2495-2500.

Prakash, Ved and Rao, Venkatesh and Pramanik, S (1982) Structural and magnetic studies of pure and substituted gamma-iron oxide. Transactions of the Indian Institute of metals, 35 (5). 513-&.

Prakash, Ved and Tewari, C R (1984) Effect of manganese on the magnetic-properties of co-14-percent al-alloys. Transactions of the Indian Institute of metals, 37 (1). 89-&.

Prakash, Ved and Tewari, C R and Bandyopadhyay, D (1981) Kinked hysteresis loop in 36-percent Ni-Fe alloy. Indian journal of pure & applied physics, 19 (5). pp. 492-494.

Prakrathi, S and Udupa K, Rajendra and Bhat K, Udaya (2013) Microstructural characterization and indentation creep behavior of friction stir modified Al surface with iron powder. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 131-140.

Pramanick, A K (2010) The Effect of Cobalt Addition on Microstructural Variation in Melt Spun ZR-Al-Cu-Ni Alloys. In: National Conference with international participation of Materials science and new materials-2008, December 4-5, 2008, Sofia, Bulgaria.

Pramanick, A K (2009) Hybrid and nanomaterials - 2009. Current Science, 96 (11). pp. 1-2.

Pramanick, A K and Gupta, Siddhi and Mishra, T and Sinha, Arvind (2012) Topographical heterogeneity in transparent PVA hydrogels studied by AFM. Materials Science and Engineering C, 32 (2). pp. 222-227.

Pramanick, A K and Mukhopadhyay, N K (2000) Aperiodic-2000. Current Science, 79 (12). pp. 1637-1643.

Pramanick, A K and Sinha, Arvind and Nayar, S and Dragieva, I (2008) Characterization of different samples by Atomic Force Microscopy. In: Nanoscience and Nanotechnology-8. Prof. Marin Drinov Academic Publishing House, Sofia, 2008, Sofia, pp. 257-262. ISBN 1311-9702

Pramanick, A K and Sinha, Arvind and Sastry, G V S and Ghosh, R N (2009) Near-grain-boundary characterization by atomic force microscopy. Ultramicroscopy, 109 (6). pp. 741-747.

Pramanick , A K and Mandal, R K and Sastry, G V S (2004) Structural stability of Al-Co-Cu-Ni decagonal phase. Journal of Non-Crystalline Solids, 334-335 . pp. 234-237.

Pramanik, M R and Ganesh, R and Pandey, L P (1981) Rapid Indirect Volumetric Method for Determination of Molybdenum in Ferro-molybdenum. NML Technical Journal, 23 (1 & 2). pp. 20-21.

Pramanik, S and Mitra, S K (2013) Hollow Briquette- A Novel Method of Agglomeration. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Pramanik, S and Rao, Venkatesh and Mohanty, O N (1993) Effect of niobium on the directional solidification and properties of alnico alloys. Journal of Materials Science, 28 (5). pp. 1237-1244.

Prasad, A K and Pathak, D D and Pan, S K (2015) Characterisation of low grade iron ores of Bursua iron ore mines. Journal of Metallurgy and Materials Science, 57(1) . pp. 1-7.

Prasad, B K and Venkateswarlu, K and Modi, O P and Jha, A K and Das, S and Dasgupta, R and Yegneswaran, A H (1998) Sliding wear behavior of some Al-Si alloys: Role of shape and size of Si particles and test conditions. Metallurgical and Materials Transactions A, 29 (11). pp. 2747-2752.

Prasad, K and Kumari, K and Chandra, K P and Yadav, K L and Sen, S (2009) Dielectric relaxation and ac conductivity of WO3 added (Na1/2Bi1/2)TiO3 ceramic. Materials Science - Poland, 27 (2). pp. 373-384.

Prasad, K and Kumari, K and Lily, and Chandra, K P and Yadav, K L and Sen, S (2007) Glass-like response of (Na1/2Bi1/2)TiO3–WO3 ceramic. Solid State Communications, 144 (1-2). pp. 42-45.

Prasad, K and Lily, and Kumari, K and Chandra, K P and Yadav, K L and Sen, S (2007) Electrical properties of a lead-free perovskite ceramic: (Na0.5Sb0.5)TiO3. Applied Physics A: Materials Science & Processing, 88 (2). pp. 377-383.

Prasad, K and Lily, and Kumari, K and Chandra, P and Yadav, K L and Sen, S (2007) Electrical properties of a lead-free perovskite ceramic: (Na0.5Sb0.5)TiO3. Applied Physics A-Materials Science & Processing, 88 (2). pp. 377-383.

Prasad, K and Singh, Raghubir and Kumar, Rajendra (1988) Application of Cr-Mn-N-C austenitic steels for exhaust valve in automotive engines. Transactions of the Indian Institute of metals, 41(6) . pp. 585-591.

Prasad, N B and Tendolkar, G S (1958) Application of Stainless Steels in Nuclear Technology. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Prasad, P and Singh, R (1995) Microstructural Studies in failed Samples. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory (CSIR), Jamshedpur.

Prasad, P M and Mankhand, T R and Rao, P S P and Prasad, A K J (2002) Kinetics of the direct synthesis of molycarbide by reduction-carburization of molybdenite in the presence of lime. Metallurgical and Materials Transactions B, 33 ( 3). pp. 345-354.

Prasad, R (1994) Thermal Surface Hardening Treatment of Steels. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Prasad, R S and Lele, S (1994) Stabilization of the amorphous phase inside carbon nanotubes - solidification in a constrained geometry. Philosophical Magazine Letters Online ISSN 1362-3036, 70 (6). pp. 357-361.

Prasad, S N and Navale, N G and Panda, S (1998) A Study on Impact Resistance of Glass Fibre Reinforced Vinylester Composites against ballistic Projectiles. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 246-253.

Prasad, Sanjay and Pandey, B D (1999) Alternative processes for treatment of chalcopyrite - a review. Minerals Engineering, 12 (2). p. 235.

Prasad, Sanjay and Pandey, B D (1999) Sulphation roasting studies on synthetic copper–iron sulphides with steam and oxygen. Canadian Metallurgical Quarterly, 38 (4). pp. 237-247.

Prasad, Sanjay and Pandey, B D (1999) Thermoanalytical Studies on Copper—Iron Sulphides. Journal of Thermal Analysis and Calorimetry, 58 (3). pp. 625-637.

Prasad, Sanjay and Pandey, B D and Palit, S K (1994) Direct sulfation of chalcopyrite with steam and oxygen. Transactions of the institution of mining and metallurgy section c-mineral processing and extractive metallurgy, 103 ( ). C69-C75.

Prasad, Sanjay and Pandey, B D and Palit, S K (1996) Kinetics of sulfation of chalcopyrite with steam and oxygen in the presence of ferric oxide. Metallurgical and Materials Transactions B-Process metallurgy and materials processing science, 27 (3). pp. 465-474.

Prasad, Sanjay and Pandey, B D and Palit, S K (1996) Sulphation of chalcopyrite with steam and oxygen in the presence of some additives. Materials Transactions JIM, 37 (6). pp. 1304-1310.

Prasad, V V S and Rao, A S and Prakash, U and Rao, V R and Rao, P K and Gupt, K M (1998) Alumina addition to fluoride slags for recycling of low oxygen high conductivity copper scrap through electroslag crucible melting. ISIJ International, 38 (12). pp. 1387-1389.

Prasad, V V S and Rao, A S and Prakash, U and Rao, Venkatesh and Rao, P K and Gupt, K M (1998) Effect of process variables on electroslag crucible melting of copper-chromium alloys. ISIJ International, 38 (12). pp. 1390-1392.

Premchand, (1996) Processing of low grade tungsten ore concentrates by hydrometallurgical route with particular reference to India. Bulletin of Materials Science, 19 (2). pp. 295-312.

Premchand, and Jana, R K (1999) Processing of polymetallic sea nodules: An overview. In: Proceedings of the third (1999) ISOPE ocean mining symposium, Nov 08-10, 1999, Goa, India.

Priyadarshi, Uddeshya and Mishra, Suman K and Kumar, K Shravan (2012) Multilayer Thermal Barrier Coating prepared by EB-PVD process and its structure property correlation. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Priyanka, and Garai, Subhadra (2011) Synthesis and Characterization of Nano Bio Ceramic/Bio Composites for Bone Tissue Regeneration. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Prodhan, A (2009) Effect of Electric Current (Plasma) Treatment on LM-6 Al-Si Alloy. Transactions Of The American Foundry Society, 117 . pp. 63-77.

Prodhan, A (2011) Semisolid processing of short and long freezing range Cu alloys by electric current. Materials Science and Technology . pp. 1513-1517.

Prodhan, A and Reddy, S R S and Prasad, S N (2000) Studies on solidification, aging and forgeability of modified stainless steels. Journal of Materials Processing Technology, 103 (2). pp. 324-331.

Prodhan, A and Sanyal, D (1998) Cooling curves analysis of aluminium solidified without and with magnetic or electric field. Journal of Materials Science Letters, 16 (11). pp. 958-961.

Puranika, Ganesha and Raj, Manish and Borkar, Moreshwar and Lakshminarasimham , B (2013) Impact Of Chemistry And Inclusions On Fracture Toughness Of Rail Steel:Case Study At JSPL. In: Procceding of the Inter national conference on science and technology of Iron making and steel making, December 16-18, 2013, CSIR-NML Jamshedpur.

Puvvada, G V K (1999) Liquid-liquid extraction of gallium from Bayer process liquor using Kelex 100 in the presence of surfactants. Hydrometallurgy , 52 (1). pp. 9-19.

Puvvada, G V K and Jana, R K and Pandey, B D and Bagchi, D and Kumar, Vinay and Premchand, (1997) Ammonia leach and solvent extraction for the recovery of valuable metals from roast-reduced polymetallic ocean nodules. In: 2nd ISOPE Ocean Mining Symposium, Nov 24-25, 1997, Seoul, South Korea.

Q

Quarrell, A G (1958) Hydrogen in Steel. In: Symposium on Production, Properties and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

R

Radhakrishna Bhat, B V and Somaraju, K and Venkataraman, B and Bhanuprasad, V V (1998) Metal Matrix Composites as Potential Armour Materials. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 103-115.

Rai, R K and Sahu, J K (2018) Strength ductility paradox in a directionally solidified nickel base superalloy. Materials Letters, 220 (IF-2.572 ). pp. 90-93.

Rai, R S and Singh, S R and Dubey, M (1986) Lattice imaging studies on structure and disorder in sic polytypes .1. Bulletin de mineralogie, 109 (5). pp. 509-527.

Raj, A and Goswami, B and Kumar, S B and Krishna, G and Roy, Nilima and Ray, Ashok K (2014) Damage Analysis of Service Exposed Reformer Tubes in Petrochemical Industries. High Temperature Materials and Processes, 33(3) (IF-0.356). pp. 201-216.

Raj, A and Goswami, B and Kumar, S B and Krishna, G and Roy, Nilima and Ray, Ashok K (2014) Performance and Life Assessment of Reformer Tubes in Petrochemical Industries. High Temperature Materials and Processes, 33(3) (IF-0.356). pp. 217-230.

Raj, A and Goswami, B and Ray, Ajoy K (2012) High speed steels - A tribute of microalloyed steels. Journal of Metallurgy and Materials Science,, 54(4) . pp. 225-248.

Raj, A and Goswami, B and Ray, Ashok K (2014) Creep and Fatigue Behavior in Micro-alloyed Steels - A Review. High Temperature Materials and Processes, 33(1) (IF-0.356). pp. 1-12.

Raj, A and Goswami, B and Ray, Ashok K (2012) Forge and heat-treatments in micro-alloyed steels. Journal of Metallurgy and Materials Science, 54(4) . pp. 249-268.

Raj, A and Goswami, B and Ray, Ashok K (2012) Precipitation, recrystallization and elemental propositions in micro-alloyed steels. Journal of Metallurgy and Materials Science, 54(3) . pp. 155-173.

Raj, Baldev and Bhattacharya, D K and Jayakumar, T (1995) Magnetic hysteresis loop parameters and Barkhausen noise for microstructural characterization of steels. Metals Materials and Processes, 7 (1). pp. 19-28.

Raj, Baldev and Jayakumar, T (2001) Assessment of Defects and Microstructures for Evaluating Damage in Pressure Retaining Components. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. NML, Jamshedpur, India, Jamshedpur, pp. 85-104. ISBN 81-87053-62-3

Raj, Manish (2011) Ultrasonic Immersion C-Scan Imaging Technique : A Novel Tool to Evaluate and Optimize EMS Parameters for Continuously Cast Steel Billet Quality. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Rajeswari, S and Jayakumar, T and Rao, C B and Bhattacharya, D K and Raj, B (1998) Residual stress measurement in ferritic steel tube welds using X-ray diffraction. Science and technology of welding and joining, 3 (4). pp. 204-207.

Raji, K (2014) Influence of density on Al-Cu composition during compaction process. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 53-57.

Raji, K and Alfred Cecil Raj, S (2012) Study of safe factor of sintered aluminium alloys using extrusion process. Journal of Metallurgy and Materials Science, 54(2) . pp. 137-142.

Raji, K and Raj, S Alfred Cecil (2010) Plasticity of tensile specimen of 7% copper in aluminium composite. Journal of Metallurgy and Materials Science, 52 (4). pp. 379-383.

Raji, K and Raj, S Alfred Cecil (2011) Micro to nano size distribution of powder particles of Al -Cu and its influence on strength properties. Journal of Metallurgy and Materials Science, 53 (4). pp. 369-374.

Rajnikanth, V and Arora, Gaurav and Narasaiah, N and Venkateswarlu, K (2008) Effect of repetitive corrugation and straightening on Al and Al–0.25Sc alloy. Materials Letters, 62 (2). pp. 301-304.

Rajnikanth, V and Mukherjee, K and Ghosh Chowdhury, S and Schiebahn, A and Harms, A and Belck, W (2013) Mechanical property and microstructure of resistance spot welded twinning induced plasticity-dual phase steels joint. Science and Technology of Welding and Joining, 18/6 (IF-1.274). pp. 485-491.

Rajnikanth, V and Munda, Parikshit and Kumar, Tipu and Ghosh Chowdhury, S and Sangal, Sandeep (2016) Effect of thermomechanical processing schedule on the texture and microstructure of pipeline grade API X80 microalloyed steel. 4 th International conference on Thermomechanical Simulation and Processing of Steels, SIMPRO 2016, 4 (NON-SCI). pp. 231-239.

Rajnikanth, V and Venkateswarlu, K (2011) An investigation of sliding wear behaviour of WC–Co coating. Tribology International, 44 (12). pp. 1711-1719.

Rajnikanth, V and Venkateswarlu, K and Sen, Mani Kuntal and Das, Mousumi and Alhajeri, S N and Langdon, T G (2011) Influence of scandium on an Al–2% Si alloy processed by high-pressure torsion. Materials Science and Engineering A, 528 (3). pp. 1702-1706.

Rajpurohit, R S and Jena, P S M and Kumar, Shivam and Sahu, J K (2021) Asymmetric cyclic loading behavior of micro-alloyed 2.25 Cr–Mo steel at room temperature. International Journal of Pressure Vessels and Piping, 191 (IF-2.230). p. 104369.

Ram, S (1994) Kinetics of the desorption of interstitial hydrogen in stable Nd2Fe14BHx, x-less-than-or-equal-to-5. Physical Review B (PRB), 49 (14). pp. 9632-9638.

Ram, S and Banerjee, H D and Halder, S and Ramachandrarao, P (1997) Formation of Nd2Fe14B hydride by milling of anhydride particles in toluene in a closed reactor. Bulletin of Materials Science, 20 (8). pp. 1049-1058.

Ram, S and Claude, E and Joubert, J C (1995) Synthesis, stability against air and moisture corrosion, and magnetic-properties of finely divided loose Nd2Fe14BHx, x-less-than-or-equal-to-5, hydride powders. IEEE Transactions on Magnetics, 31 (3). pp. 2200-2208.

Ram, S and Fecht, H J and Halder, S and Ramachandrarao, P and Banerjee, H D (1997) Calorimetric study of the desorption of the interstitial hydrogen atoms in ferromagnetic Nd2Fe14BHx (x<=5) microcrystals. Physical Review B (PRB), 56 (2). pp. 726-737.

Ram, S and Halder, S (1996) Medium-range structural ordering and macroscopic interactions in 1 to 2 mm thin two-dimensional platelets of borate glasses. Physica status solidi b-basic research, 195 (2). pp. 343-351.

Ram, S and Singh, T B and Pathak, L C (1998) Synthesis and thermogravimetric analysis of amorphous boehmite fibres. Physica Status Solidi A-applied research, 165 (1). pp. 151-164.

Ramachandran, E G and Dasarathy, C (1960) Hydrogen and austenite stabilization. Acta Metallurgica, 8 (10). pp. 729-730.

Ramachandran, E G and Dasarathy, C (1960) Stability of retained austenite on ageing. Acta Metallurgica, 8 (4). pp. 274-275.

Ramachandran, E G and Dasarathy, C (1960) A thermal stabilization of austenite. Acta Metallurgica, 8 (9). pp. 666-667.

Ramachandrarao, P (1997) Evolution of microstructure in rapidly solidified alloys. Metals Materials and Processes, 9 (3). pp. 221-228.

Ramachandrarao, P (1997) Iron and Steel Heritage of India : Contributions from the National Metallurgical Laboratory. In: Iron and Steel Heritage of India, November 1997, IIM & Tata Steel,Jamshedpur.

Ramachandrarao, P (1992) Rapid solidification of steels. Bulletin of materials science, 15 (6). pp. 503-513.

Ramachandrarao, P (1993) Report on the discussion meeting on icosahedral symmetry in materials. Current Science, 64 (10). pp. 708-709.

Ramachandrarao, P (1997) Studies on undercooled metallic melts. Progress in Materials Science, 42 (1-4). pp. 301-309.

Ramachandrarao, P and Dubey, K S (1995) A thermodynamic approach to the viscous behavior of glass-forming liquids. Materials Science and Engineering B-Solid State Materials for Advanced Technology , 32 (3). pp. 285-293.

Ramachandrarao, P and Dubey, K S (1995) A thermodynamic approach to the viscous behaviour of glass-forming liquids. Materials Science and Engineering B, 32 (3). pp. 285-293.

Ramachandrarao, P and Sinha, Arvind and Rao, Venkatesh (1997) Perspectives in rare earth magnets. Metals materials and processes, 9 (1). pp. 65-73.

Ramachandrarao, P and Srikanth, S (1998) Can there be a second kind of entropy catastrophe in the melting of metastable solids? Journal of Materials Research, 13 (11). pp. 3270-3274.

Ramachandrarao, P and Srikanth, S (1995) Enthalpy of peritectic transformations from phase-diagram data. Scripta Metallurgica, 32 (2). pp. 161-166.

Ramachandrarao, P and Srikanth, S (1995) Estimation of the enthalpy of peritectic transformations from phase diagram data. Scripta Metallurgica et Materialia, 32 (2). pp. 161-166.

Ramadas, and Balasubramaniam, Krishnan and Joshi, Makarand (2011) Propagation Characteristics of Ao Mode in a Metallic Beam Containing a Semi-infinite Crack. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries -NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Ramanathan, K and Periasamy, V M and Malathy, and Pushpavanamb, and Natarajan, U (2008) Prediction of volume fraction of diamond deposition in Ni-diamond composite coatings - An artificial neural network approach. Journal of Metallurgy and Materials Science, 50 (1). pp. 57-64.

Randhawa, N S and Dwivedi, D and Prajapati, S and Jana, R K (2015) Application of manganese nodules leaching residue for adsorption of nickel(II) ions from aqueous solution. International Journal of Environmental Science and Technology, 12(3) (IF-1.794). pp. 857-864.

Ranganath, V R (2001) Shaft Failures in Coal Handling Plants. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. NML, Jamshedpur, India, Jamshedpur, pp. 32-38. ISBN 81-87053-62-3

Ranganath, V R and Pandey, R K and Kumar, A N (1990) A comparative study of various approaches for CTOD toughness evaluation. Engineering Fracture Mechanics, 37 (5). pp. 1059-1069.

Ranganath, V R and Tarafder, S (1995) Application of fracture-mechanics for weld integrity assessment. Sadhana-academy proceedings in engineering sciences, 20 ( ). pp. 233-246.

Ranganathan, M V and Mathur, G P and Altekar, V A (1982) From bench scale to industrial concentrator - the story of a 500-tpd beneficiation project. Cim Bulletin, 75 (845). p. 82.

Ranganathan, S (1991) The entity model of metallic solutions. Calphad-Computer Coupling of Phase Diagrams and Thermochemistry, 15 (2). pp. 121-130.

Ranganathan, S (1991) Operational diagram for sulfide roasting. Zeitschrift fur metallkunde, 82 (9). pp. 709-712.

Ranganathan, S (2004) Pre-Reduction of Chromite Ores. In: Proceeding of International Seminar on 1st Ferro Alloys India, 8-10 Feb 2004, Hyderabad, India.

Ranganathan, S (1999) A technique for prediction of carbonitride precipitation in high strength low alloy steels. Materials science and technology , 15 (5). pp. 523-526.

Ranganathan, S (1998) Thermochemical analysis of production of ferrochromium in submerged arc furnace. Ironmaking & Steelmaking, 25 (6). pp. 466-471.

Ranganathan, S and Godiwalla, K M (1998) Influence of pre-reduction of ore on the temperature profile inside a submerged-arc furnace producing ferro-chromium. Steel Research, 69 (12). pp. 476-481.

Ranganathan, S and Godiwalla, K M (2011) Influence of process parameters on reduction contours during production of ferrochromium in submerged arc furnace. Canadian Metallurgical Quarterly , 50 (1). pp. 37-44.

Ranganathan, S and Mishra, S N and Mishra, R and Singh, B K (2005) Control of silicon in high carbon ferrochromium produced in submerged arc furnace through redistribution of quartzite in the charge bed. Ironmaking & Steelmaking, 32 (2). pp. 177-184.

Ranganathan, S and Nath, Paras and Sivaram, K (2002) Optimization of specific energy consumption in the production of ferro-chromium by optimizing electrode-coordinates in submerged-arc furnace. Journal of Metallurgy and materials Science., 44 (3). pp. 127-133.

Ranganathan, S and Ramachandrarao, P (2010) Thermodynamic modelling of the spontaneous vitrification process using transformation diagrams. Calphad, 34 . pp. 387-392.

Ranganathan, S and Sen, P K and Mishra, S N and Mishra, R (1999) Application of thermo-chemical analysis to control the recovery of silicon during the production of ferro-chromium in submerged-arc furnace. Icarism '99: proceedings of the international conference on alternative routes of iron and steelmaking, 99 (3). pp. 277-279.

Ranjan, Maindra and Ghosh, M (2012) The Effect of Cooling Rates on Vanadium Microalloyed Steel. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Ranjan, Priya and Goswami, B and Prasad, Sanjay and Sharma, G S and Singh, R P and Prasad Rao, S Siva and Das, Goutam (2013) Microstructure and properties of the new bainitic rail steels. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 119-130.

Ranjan, Rajeev and Srivastava, R K and Paswan, M K (2013) Quality Engineering Applications in Continuous Casting for Steel Making Technology. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Ranjitham, A M and Khangaonkar, P R (1989) Hydration of calcined magnesite at elevated-temperatures under turbulent conditions. Minerals Engineering, 2 (2). pp. 263-270.

Ranjitham, A M and Khangaonkar, P R (1990) Leaching behaviour of calcined magnesite with ammonium-chloride solutions. Hydrometallurgy, 23 (2-3). pp. 177-189.

Rao, A S and Gupta, K K and Singh, Manjit and Upadhyay, A K and Sircar, J K (2006) Interelemental interference correction by computational method in flame atomic absorption spectroscopy (FAAS): Study of Fe-Mn system in silico-manganese ferro-alloy. Indian Journal Of Chemical Technology , 13 (1). pp. 77-80.

Rao, A S and Prasad, V V S and Baligidad, R G and Rao, V R and Sarma, D S (1999) Influence of hot working on electro slag remelted low alloy steel. Transactions of Indian Institute of Metals, 52 (2-3). pp. 139-146.

Rao, Addanki S and Gupta, K K and Sircar, J K and Srivastava, S C (2004) A rapid flame atomic absorption spectroscopic procedure for determination of lead in aluminium base alloys. Indian Journal Of Chemical Technology , 11 (4). pp. 475-478.

Rao, Ch. Sridhar (1996) Titanium as an Automotive Material. NML Technical Journal, 38 (2). pp. 43-50.

Rao, G N and Prasad, P R (1967) Riser dimensioning-a new approach for grey iron castings. NML Technical Journal, 9 (1). pp. 27-28.

Rao, K N P (1958) Alloy and Tool Steel Industry in India. In: Symposium on Production, Properties & Applications of Alloy & Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Rao, K N P (1959) Trend of Steel Demand in India. NML Technical Journal, 1 (1). pp. 41-46.

Rao, PDP and Peravadhanulu, A and Chakrabarti, D M and Chakravorty, N (1985) Beneficiation studies on molybdenite at the national metallurgical laboratory. Transactions of the Indian Institute of metals, 38 (2). pp. 153-155.

Rao, V (1994) Mechanical Processing in Magnetic Materials. In: Tailoring of properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Rao, V V (1992) Centrifugal atomization and rapid-solidification processing of high-strength aluminum-alloys. Journal of Materials Science Letters , 11 (3). pp. 135-137.

Rao, V V (2004) An electrolytic method for studying the microstructure and grain size of Al-1.25 % Mn alloy. Indian Journal Of Engineering And Materials Sciences , 11 (3). pp. 224-226.

Rao, V V (1992) Microstructural features of rapidly solidified 7075 alloy containing 1.0 wt% Mn. Scripta Metallurgica et Materialia, 26 (5). pp. 819-823.

Rao, V V (1999) Microstructure and properties of high strength aluminium alloys subjected to rapid solidification processing. Indian Journal of Engineering and Materials sciences, 6 (3). pp. 158-163.

Rao, V V (2006) A modified gun technique for melt quenching of reactive alloys. Indian Journal Of Engineering And Materials Sciences , 13 (5). pp. 451-454.

Rao, V V (1998) Prepararion of Al2O3 ceramic matrix in-situ composites by reactive melt penetration. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 132-136.

Rao, V V (2001) Preparation and properties of Al2O3/Al in-situ composites by reactive melt penetration. Indian Journal of Engineering and Materials Sciences, 8 (3). pp. 161-164.

Rao, V V (2003) Preparation of net-shape Al2O3/Al3Ni in situ composites by reactive melt penetration. Indian Journal Of Engineering And Materials Sciences , 10 (5). pp. 424-426.

Rao, V V (2006) A structural study of copper-43at% cadmium alloy. Indian Journal Of Engineering And Materials Sciences , 13 (6). pp. 531-534.

Rao, V Venkateswara (1991) Centrifugal Atomisation and Rapid Solidification Processing of High Strength Aluminium Alloys Containing Transition Elements. NML Technical Journal, 33 (1-2). pp. 31-37.

Rao, V Venkateswara (2004) An electrolytic method for studying the microstructure and grain size of Al-1.25% Mn alloy. Indian Journal of Engineering and Materials Sciences, 11 (3). pp. 224-226.

Rao, Venkatesh and Mitra, A (1995) Phase-transformation studies on mn-al-c alloy, by dsc and electrical-resistivity measurements. Journal of Thermal Analysis, 44 (2). pp. 375-384.

Rao, Venkatesh and Pramanik, S and Tewari, C R and Singh, S R and Mohanty, O N (1989) Phase-transformations in Mn-Al permanent-magnet alloys. Journal of Materials Science, 24 (11). pp. 4088-4093.

Rao, W and Mukherjee, S P and Kumar, Rajendra (1978) Structure and mechanical-properties of rapidly solidified aluminum-alloys. Transactions of the Indian Institute of Metals, 31 (5-6). 383-&.

Rao, Y S and Bandyopadhyay, A and E, Murugan (2013) Recycling of Corex Sludge Through Sludge Agglomeration Process. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Raposo, V and Vazquez, M and Mitra, A (2003) Torsion dependence of giant magnetoimpedance in amorphous wires. Journal of Magnetism and Magnetic Materials, 254-255 ( ). pp. 179-181.

Rath, C and Mishra, N C and Anand, S and Das, R P and Sahu, K K and Upadhyay, C and Verma, H C (2000) Appearance of superparamagnetism on heating nanosize Mn0.65Zn0.35Fe2O4. Applied Physics Letters, 76 (IF-4.00). pp. 475-477.

Rath, C and Sahu, K K and Kulkarni, S D and Anand, S and Date, S K and Das, R P and Mitra, N C (1999) Microstructure-dependent coercivity in monodispersed hematite particles. Applied Physics Letters, 75 (26). pp. 4171-4173.

Rausch, Hans and Cappel, F (1960) Pilot Plants for the Agglomeration of Iron Ores on a Semi-Industrial Scale. NML Technical Journal, 2 (1). pp. 27-34.

Ravi Kumar, B (2010) Influence of crystallographic textures on tensile properties of 316L austenitic stainless steel. Journal of Materials Science, 45 (10). pp. 2598-2605.

Ravi Kumar, B (2012) Progress of Recrystallisation in Cold Rolled Austenitic Stainless Steel during Cyclic Thermal Process. Materials Science Forum . pp. 627-630.

Ravi Kumar, B and Das, Swapan K and Mahato, B and Ghosh, R N (2010) Role of strain-induced martensite on microstructural evolution during annealing of metastable austenitic stainless steel. Journal of Materials Science, 45 (4). pp. 911-918.

Ravi Kumar, B and Das, Swapan K and Sharma, Sailaja and Sahu, J K (2010) Effect of thermal cycles on heavily cold deformed AISI 304L austenitic stainless steel. Materials Science and Engineering: A, 527 (4-5). pp. 875-882.

Ravi Kumar, B and Ghosh Chowdhury, S and Narasaiah, N and Mahato, B and Das, Swapan K (2007) Role of Grain Boundary Character Distribution on Tensile Properties of 304L Stainless Steel. Metallurgical and Materials Transactions A, 38 (5). pp. 1136-1143.

Ravi Kumar, B and Mahato, B and Bandopadhyay, N R and Bhattacharya, D K (2005) Influence of strain-induced phase transformation on the surface crystallographic texture in cold-rolled-and-aged austenitic stainless steel. Metallurgical and Materials Transactions A, 36 (11). pp. 3165-3174.

Ravi Kumar, B and Mahato, B and Sharma, S and Sahu, J K (2009) Effect of Cyclic Thermal Process on Ultrafine Grain Formation in AISI 304L Austenitic Stainless Steel. Metallurgical And Materials Transactions A-Physical Metallurgy And Materials Science , 40A (13). pp. 3226-3234.

Ravi Kumar, B and Mahato, B and Singh, Raghuvir (2007) Influence of Cold-Worked Structure on Electrochemical Properties of Austenitic Stainless Steels. Metallurgical and Materials Transactions A, 38 (9). pp. 2085-2094.

Ravi Kumar, B and Mohanty, O N (1992) On the correct prediction of isothermal transformation diagrams for low-carbon and low-alloy steels - comment on available data. Scripta Metallurgica Et Materialia , 26 (11). pp. 133-137.

Ravi Kumar, B and Mohanty, O N and Biswas, A (1992) Welding of thin steel plates - a new model for thermal-analysis. Journal of Materials Science, 27 (1). pp. 203-209.

Ravi Kumar, B and Murthy, G V S and Mahato, B and Metya, Avijit Kumar and Gunjan, M K and Singh, S R (2011) Non-Destructive and Destructive Investigation of MLG Parts of MIG 29 Aircraft (TMP-0165). Other (TMP). National Metallurgical Laboratory (NML), Jamshedpur. (Submitted)

Ravi Kumar, B and Sharma, S (2013) Recrystallisation Characteristics of Cold Rolled Austenitic Stainless Steel during Repeated Annealing. Recrystallization and Grain Growth V, 753 . pp. 157-162.

Ravi Kumar, B and Sharma, S and Kashyap, B P and Prabhu, N S (2015) Ultrafine grained microstructure tailoring in austenitic stainless steel for enhanced plasticity. Materials & Design, 68 (IF-3.171). pp. 63-71.

Ravi Kumar, B and Sharma, Sailaja and Mahato, B (2011) Formation of ultrafine grained microstructure in the austenitic stainless steel and its impact on tensile properties. Materials Science and Engineering A, 528 (6). pp. 2209-2216.

Ravi Kumar, B and Sharma, Sailaja and Munda, Parikshit and Minz, R K (2013) Structure and microstructure evolution of a ternary Fe–Cr–Ni alloy akin to super martensitic stainless steel. Materials & Design, 50 (IF-2.913). pp. 392-398.

Ravi Kumar, B and Singh, A K and Das, Samar and Bhattacharya, D K (2004) Cold rolling texture in AISI 304 stainless steel. Materials Science and Engineering A, 364 (1-2). pp. 132-139.

Ravi Kumar, B and Singh, S R and Mahato, B (2006) XRD Residual Stress Analysis of Life-Expired Main Landing Gear of AN-32 Aircraft. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Ravichandran, K and Kumar, N M and Subash, K and Sankara Narayanan, T S N (2001) Mannich base derivatives - A novel class of corrosion inhibitors for cooling water systems. Corrosion Reviews, 19 (1). pp. 29-42.

Ravichandran, K and Sankara Narayanan, T S N (2004) Corrosion of brass in cooling water systems - Role of Mannich base derivatives. Corrosion Reviews , 22 (1). pp. 71-84.

Ravichandran, K and Sankara Narayanan, T S N (2002) Effective screening of scaling inhibitors for cooling water systems - Development of an accelerated electrochemical method. Corrosion Reviews, 20 (1-2). pp. 105-113.

Ravichandran, K and Sankara Narayanan, T S N (2001) Studies on acceleration of the low temperature zinc phosphating processes. Transactions of the Institute of Metal Finishing, 79 (4). pp. 143-145.

Ray, A K and Tarafder, S and Das, D K and Venkatraman, B and Roy, P K and Goswami, B and Tiwari, Y N and Palit Sagar, S and Ranganath, V R and Das, Goutam and Chaudhuri, S and Ghosh, R N (2004) Damage resistance of thermal barrier coated superalloy in combustion chamber liner. Journal of Metallurgy and Materials Science, 46 (4). pp. 205-212.

Ray, A K and Tiwari, Y N and Sinha, R K and Roy, S K and Singh, R and Chaudhuri, S (2000) Mechanical Property Evaluation and Remaining Life Assessment of Service - Exposed Steam Pipe of Boilers in : Thermal Power Plant. High Temperature Materials and Process, 20 (1). pp. 1-12.

Ray, Ajoy K and Bhattacharya, D K and Das, Goutam (1996) Acoustic emission studies during indentation on ceramic and ceramic composite. Trends in nde science and technology - proceedings of the 14th world conference on ndt (14th wcndt),, 1-5 ( ). pp. 2455-2458.

Ray, Ajoy K and Chatterjee, S and Singh, J K and Bapari, H (2015) Thermal Exfoliation of Natural Cellulosic Material for Graphene Synthesis. Journal of Materials Engineering and Performance, 24(1) (IF-0.981). pp. 80-84.

Ray, Ajoy K and Das, Swapan K and Roy, P K and Banerjee, S (1995) Fatigued and fractured regions in a silicon-carbide whisker-reinforced alumina composite. Journal of Biomaterials Science, Polymer Edition, 15 (3). pp. 191-199.

Ray, Ajoy K and Kar, Abhijit and Ghosh, M (2007) Microstructural characterization of tin lead and lead free solder joint interface. In: Inter. Symp. on Advanced Materials and Processing, ISAMP-2007, 29-30 Oct. 2007, Basaveshwar Engineering College, Bagalkot..

Ray, Ajoy K and Kar , Abhijit and Kori, S A and Pathak , L C and Sonnad, A N (2013) Graphite-to-304SS Braze Joining by Active Metal-Brazing Technique : Improvement of Mechanical Properties. Journal of Materials Enginnering and Performance, 22(1) (IF-0.915). pp. 258-266.

Ray, Ajoy K and Mandal, S and Das, S K and Krishnan, C S S (1998) Low Cost In-Situ Formation of AIN - B- SiC. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 151-159.

Ray, Ajoy K and Sahu, Ranjan K and Rajnikanth, V and Bapari, H and Ghosh, M and Paul, Parimal (2012) Preparation and characterization of graphene and Ni-decorated graphene using flower petals as the precursor material. Carbon, 50 (11). pp. 4123-4129.

Ray, Ajoy K and Tiwari, Y N and Chaudhuri, S and Ranganath, V R and Sivaprasad, S and Roy, P K and Das, Goutam and Ghosh Chowdhury, S and Kumar, P and Ghosh, R N (2002) Remaining life assessment of service exposed reheater and superheater tubes in a boiler of a thermal power plant. Engineering Failure Analysis , 21 (1-2). pp. 109-121.

Ray, Ashok K (2000) Failure mode of thermal barrier coatings for gas turbine vanes under bending. International Journal of Turbo & Jet-engines, 17 (1). pp. 1-24.

Ray, Ashok K (1998) A new technique for precracking ceramic specimens in fatigue and fracture. Journal of the European Ceramic Society, 18 (12). pp. 1655-1662.

Ray, Ashok K and Banerjee, S and Fuller, E R and Das, Swapan K (1994) Fractography as well as fatigue and fracture of 25-wt-percent silicon-carbide whisker-reinforced alumina ceramic composite. Bulletin of Materials Science, 17 (6). pp. 893-910.

Ray, Ashok K and Bose, S C and De, P K and Das, D K (2010) Lifetime evaluation of a thick thermal barrier coated superalloy used in turbine blade. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing, 527 (21-22). pp. 5474-5483.

Ray, Ashok K and Bose, S C and De, P K and Mandal, D and Alam, H Z and Sharma, VSRA and Das, D K (2010) Evaluation of the Lifetime and Effect of Furnace Thermal Cycling on Stress Rupture Behaviour of a Thermal Barrier Coated Superalloy Used in a Turbine Blade. Canadian Metallurgical Quarterly, 49 (2). pp. 191-214.

Ray, Ashok K and Das, D K (2006) Accelerated creep resistance of thermal barrier coated superalloy. Materials Letters, 60 (25-26). pp. 3019-3022.

Ray, Ashok K and Das, Swapan K and Mondal, S and Ramachandrarao, P (2004) Microstructural characterization of bamboo. Journal of Materials Science, 39 (3). pp. 1055-1060.

Ray, Ashok K and Das, Swapan K and Pathak, L C (2003) Synthesis of silicon carbide mats using natural fibers. Materials Letters, 57 (5-6). pp. 1120-1123.

Ray, Ashok K and Das, Swapan K and Roy, P K and Banerjee, S (1995) Fractography of fatigued and fractured regions in a silicon carbide whisker reinforced alumina composite. Journal of the European Ceramic Society, 15 (3). pp. 191-199.

Ray, Ashok K and Diwakar, K and Roy, Nilima and Das, H K and Sahu, J K and Ghosh, R N (2008) Creep behaviour and stress analysis of a seventeen-year service-exposed primary super heater tube in a thermal power plant. Canadian Metallurgical Quarterly, 47 (4). pp. 469-478.

Ray, Ashok K and Diwakar, K and Sahu, J K and Das, H K and Roy, Nilima and Ghosh, R N (2008) Stress Analysis and Creep Behavior of Service Exposed Primary Superheater Tube in a Thermal Power Plant. High Temperature Materials And Processes, 27 (2). pp. 79-89.

Ray, Ashok K and Fuller, E R and Banerjee, S (1996) Fatigue crack growth rate and fracture toughness of 25 wt% silicon carbide whisker reinforced alumina composite with residual porosity. Journal of the European Ceramic Society, 16 (5). pp. 503-513.

Ray, Ashok K and Goswami, B (2004) Applications of thermal barrier coating system in gas turbines - A review. Journal of Metallurgy and materials Science, 46 (1). pp. 1-22.

Ray, Ashok K and Goswami, B and Kar, Abhijit and Ray, Ajoy K and Das, H K and Roy, P K and Kumar, S B and Bose, S C (2008) Damage resistance of a thermal barrier coated superalloy for combustor liners in aero turbines during fatigue and creep. Canadian Metallurgical Quarterly, 47 (4). pp. 479-493.

Ray, Ashok K and Goswami, B and Kumar, S B and Das, D and Das, Swapan K and Sharma, A and Das, D K (2008) Influence of thermally grown oxide scale on fatigue resistance of a thermal barrier coated superalloy. Canadian Metallurgical Quarterly, 47 (1). pp. 99-109.

Ray, Ashok K and Goswami, B and Kumar, S B and Sahay, S K (2008) Damage assessment and life prediction of TBC systems. Journal of Metallurgy and Materials Science, 50 (3). pp. 127-150.

Ray, Ashok K and Goswami, B and Kumar, S B and Sahay, S K (2008) Fatigue in gas turbine components. Journal of Metallurgy and Materials Science, 50 (2). pp. 85-105.

Ray, Ashok K and Goswami, B and Raj, A and Singh, M P (2014) Frontiers of micro-alloyed steel for industrial merchandising - 3. Journal of Metallurgy and Materials Science, 56(2) (NON-SCI). pp. 77-91.

Ray, Ashok K and Goswami, B and Raj, A and Singh, M P (2013) Frontiers of micro-alloyed steel for industrial merchandising-1. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 83-98.

Ray, Ashok K and Goswami, B and Raj, A and Singh, M P (2014) Frontiers of micro-alloyed steel for industrial merchandising-2. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 1-14.

Ray, Ashok K and Goswami, B and Raj, A and Singh, M P (2013) High strength low alloy steels. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 21-36.

Ray, Ashok K and Goswami, B and Raj, A and Singh, M P (2013) Studies on pyrometallurgy of vanadium bearing iron, steel and slag. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 99-111.

Ray, Ashok K and Guguloth, K and Swaminathan, J and Bose, S C and Roy, Nilima and Tiwari, Y N and Roy, P K and Alam, Z and Sharma, VSRA and Joshi, Srikanth V and Venkataraman, B and Das, D K (2009) Damage Resistance of a Thermal Barrier Coated Superalloy Used in Aero Turbine Blade under Accelerated Creep Condition. High Temperature Materials And Processes, 28 (1-2). pp. 35-53.

Ray, Ashok K and Kumar, S and Guguloth, K and Gunjan, M K and Goswami, B and Bose, S C (2011) Microstructural studies and remnant life assessment of eleven years service exposed reformer tube. Materials Science and Engineering A, 529 (1). pp. 102-112.

Ray, Ashok K and Mahanty, G and Ghose, A (1991) Effect of catalysts and temperature on silicon-carbide whiskers formation from rice husk. Journal of Materials Science, 10 (4). pp. 227-229.

Ray, Ashok K and Mondal, S and Das, Swapan K and Ramachandrarao, P (2005) Bamboo—A functionally graded composite-correlation between microstructure and mechanical strength. Journal of Materials Science, 40 (19). pp. 5249-5253.

Ray, Ashok K and Mukhopadhyay, N K and Bhattacharya, D K and Dwarakadasa, E S and Parida, N (1999) Studies on indentation fracture toughness on ceramic and ceramic composite using acoustic emission technique. Bulletin of Materials Science, 22 (1). pp. 25-32.

Ray, Ashok K and Roy, Nilima (2002) Modelling of Elasto-Plastic Deformation and Crack Propagation Studies in Thermal Barrier Coated Superalloys. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Ray, Ashok K and Roy, Nilima and Dash, Byomkesh and Das, D K and Ranganath, V R and Goswami, B and Singh, M P and Tiwari, Y N and Roy, P K and Das, H K and Sanyal, D and Dwarakadasa, E S (2006) High temperature mechanical properties of thermal barrier coated superalloy applied to combustor liner of aero engines. High Temperature Materials And Processes , 25 (3). pp. 109-119.

Ray, Ashok K and Roy, Nilima and Dash, Byomkesh and Ranganath, V R and Tiwari, Y N and Goswami, B and Dwarakadasa, E S (2010) Failure: Chapter 8. In: Introduction to the science and engineering of materials; MSE 209. Uinversity of Virginia, USA.

Ray, Ashok K and Roy, Nilima and Godiwalla, K M (2001) Crack propagation studies and bond coat properties in thermal barrier coatings under bending. Bulletin of Materials Science, 24 (2). pp. 203-209.

Ray, Ashok K and Roy, Nilima and Kar, Abhijit and Ray, Ajoy K and Bose, S C and Das, Goutam and Sahu, J K and Das, D K and Venkataraman, B and Joshi, Srikanth V (2009) Mechanical property and characterization of a NiCoCrAlY type metallic bond coat used in turbine blade. Materials Science and Engineering: A, 505 (1-2). pp. 96-104.

Ray, Ashok K and Roy, Nilima and Matwa, M and Davuluri, A and Kumari, A and Kumar, P and Mundhada, D and Kaushal, V and Roy, B N (2014) Uncertainty in Damage Assessment and Remaining Life Prediction of Engineering Materials Used In Petrochemical Industry. Petroleum & Environmental Biotechnology, 5(4) . pp. 1-16.

Ray, Ashok K and Roy, Nilima and Raj, A and Roy, B N (2016) Structural integrity of service exposed primary reformer tube in a petrochemical industry. International Journal of Pressure Vessels and Piping, 137 (IF-1.28). pp. 46-57.

Ray, Ashok K and Roy, Nilima and Sahu, J K and Tiwari, Y N and Ray, R K and Sharma, R K and Gunjan, M K and Singh, S R (2011) Studies on creep behaviour and Statistical analysis of services exposed P-22 grade of Steel. Exploratory (OLP). CSIR-NML, Jamshdpur.

Ray, Ashok K and Roy, P K (2012) High Cycle Fatigue and Cyclic Plastic Deformation Behav-iour of High Temperature Oxidation Resistant Titanium Aluminide Coated IMI834 Alloy at 873K. High Temperature Materials Proceeding, 31 . pp. 691-699.

Ray, Ashok K and Singh, S R and Kailath, A J and Roy, P K and Das, Swapan K and Ghosh, R N (2005) Fatigue and creep damage and its correlation with microstructure of a service exposed first stage turbine blade in a power plant. Journal of Metallurgy and Materials Science, 47 (2). pp. 59-69.

Ray, Ashok K and Steinbrech, R W (1999) Crack propagation studies of thermal barrier coatings under bending. Journal of the European Ceramic Society, 19 (12). pp. 2097-2109.

Ray, Ashok K and Tiwari, Y N and Chaudhuri, S and Ranganath, V R and Sivaprasad, S and Roy, P K and Das, Goutam and Ghosh, Sabita and Kumar, P and Ghosh, R N (2002) Remaining life assessment of service exposed reheater and superheater tubes in a boiler of a thermal power plant. High Temperature Materials and Processes, 21 (1-2). pp. 109-121.

Ray, Ashok K and Tiwari, Y N and Guguloth, K and Das, Goutam and Gunjan, M K and Bose, S C and Ghosh, R N (2011) Health assessment of 22 years service-exposed radiant tube from an oil refinery. Engineering Failure Analysis, 18 (3). pp. 1067-1075.

Ray, Ashok K and Tiwari, Y N and Khan, A J and Roy, P K and Das, Goutam and Singh, Raghubir (2004) Health assessment of radiant heater tube. High Temperature Materials and Processes , 24 (1). pp. 35-45.

Ray, Ashok K and Tiwari, Y N and Sinha, R K and Singh, Raghuvir and Chaudhuri, S (1997) Remaining life assessment of service exposed reactor and distillation column materials used in a petrochemical industry. In: Recent Advances in Metallurgical Processes - Vol I, 16-19 July 1997, I I S, Banglore.

Ray, Ashok K and Tiwari, Y N and Sinha, R K and Sinha, S K and Roy, P K and Singh, Raghubir and Chaudhuri, S (2001) Mechanical property evaluation and remaining life assessment of service-exposed steam pipe of boilers in a thermal power plant. High Temperature Materials and Processes, 20 (1). pp. 39-50.

Ray, Ashok K and Whittenberger, J D (2009) Stress rupture behavior of a thermal barrier coated AE 437A Ni-based superalloy used for aero turbine blades. Materials Science and Engineering: A, 509 (1-2). pp. 111-114.

Ray, B C and Hassan, S T and Clegg, D W (1998) Effects of Thermal Shock on Mechanical Behaviour of Kevlar Fibre Composites. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 214-223.

Ray, K K and Dutta, K and Sivaprasad, S and Tarafder, S (2010) Fatigue damage of AISI 304 LN stainless steel: Role of mean stress. Procedia Engineering, 2 (1). pp. 1805-1813.

Ray, K K and Narasaiah, N and Tarafder, S (2006) Comparative Assessment of Fatigue-Thresholds Estimated by Short and Long Cracks. In: Fracture of Nano and Engineering Materials and Structures. Proceedings of the 16th European Conference of Fracture, Alexandroupolis, Greece, July 3–7, 2006 (B.). Springer, Netherlands, pp. 221-222. ISBN 978-1-4020-4971-2 (Print) 978-1-4020-4972-9 (Online)

Ray, Mallar and Sarkar, S and Bandyopadhyay, N R and Hossain, S M and Pramanick, A K (2009) Silicon and silicon oxide core-shell nanoparticles: Structural and photoluminescence characteristics. Journal of Applied Physics, 105 (7). 074301.

Ray, Samit K and Mohanty, O N (1989) On predicting the extent of magnetic aging in electrical steels. Journal of Magnetism and Magnetic Materials, 78 (2). pp. 255-262.

Reddy, A and Kotiveerachari, B (2011) Influence of microstructural changes caused by ageing on wear behaviour of Al6061/SiC composites. Journal of Metallurgy and Materials Science, 53 (1). pp. 31-39.

Reddy, P S R (2013) Challenges and opertunities of coal cleaning in India. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Reddy, S and Wasnik, S and Guha, Avijit and Kumar, J M and Sinha, Arvind and Singh, Shashi (2013) Evaluation of nano-biphasic calcium phosphate ceramics for bone tissue engineering applications : In vitro and preliminary in vivo studies. Journal of Biomaterials Applications, 27(5) (IF-2.640). pp. 565-575.

Reddy, S P and Sarath, K Sai (2013) Characterstics of Al-15% graphite composites. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 73-76.

Reeve, M R (1961) Present Trends in Methods of Production of Aluminium Alloy Slabs and Billets for Working. NML Technical Journal, 3 (1). pp. 46-55.

Renganathan, C and Raghunath, V (1994) Fluidised Bed Heat Treatment - A Flexible Heat Treating Technology. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Robiette, A G (1962) The Extraction of Vanadium from Titaniferous Iron Ores. NML Technical Journal, 4 (1). pp. 26-29.

Rojas, Jose I and Bathula, Venkata Siva and Sahoo, K L and Crespo, Daniel (2018) Viscoelastic behaviour of a novel aluminium metal matrix composite and comparison with pure aluminium,aluminum alloys and a composite made of Al-Mg-Si alloy reinforced with SiC particles. Journal of Alloys and Compounds, 744 (IF-3.133). pp. 445-452.

Roshan, Vibhuti and Chandra, Anand and Sharma, S K and Nageswara Rao, G V S (2013) Effect of Surface Area on Green Properties of Micro Pellets. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Rout, Bapin K and Awasthi, S and Choudhary, S K and Singh, R K and Ajmani, S K (2013) Development of Nozzle Clogging Index to Assess The Casting Behavior During Continuous Slab Caster At. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Roy, A and Manna, I and Chattoraj, I (2014) Anomalies in hydrogen enhanced fatigue of a high strength steel. International Journal of Fatigue, 59 (IF-1.730). pp. 14-22.

Roy, Arijit and Manna, I and Tarafder, S and Chattoraj, I (2013) Hydrogen interactions with overload in modifying fatigue crack growth rate recovery in an HSLA steel. Materials Science and Engineering A, 579 (IF-2.108). pp. 9-17.

Roy, Arijit and Manna, I and Tarafder, S and Sivaprasad, S and Paswan, S and Chattoraj, I (2013) Hydrogen enhanced fatigue crack growth in an HSLA steel. Materials Science and Engineering A, 588 (IF-2.108). pp. 86-96.

Roy, H and Parida, N and Sivaprasad, S and Tarafder, S and Ray, K K (2008) Acoustic emissions during fracture toughness tests of steels exhibiting varying ductility. Materials Science and Engineering: A, 486 (1-2). pp. 562-571.

Roy, H and Sivaprasad, S and Tarafder, S and Ray, K K (2009) Monotonic vis-à-vis cyclic fracture behaviour of AISI 304LN stainless steel. Engineering Fracture Mechanics, 76 (12). pp. 1822-1832.

Roy, Himadri and Sivaprasad, S and Tarafder, S and Ray, K K (2009) Crack Tip Damage Mechanism under Monotonic and Cyclic Loading Conditions. Key Engineering Materials , 417-418 (8). pp. 105-108.

Roy, Himadri and Sivaprasad, S and Tarafder, S and Ray, K K (2012) Cyclic fracture behaviour of 304LN stainless steel under load and displacement control modes. Fatigue & fracture of engineering materials & structures, 35 (2). pp. 108-113.

Roy, Nilima and Bagui, S and Sahu, J K and Ray, A K (2013) Creep characterization and damage assessment of long term service exposed P-22 grade of steel. Materials Science and Engineering A, 560 (IF-2.108). pp. 802-810.

Roy, Nilima and Bose, S C and Ghosh, R N (2010) Stochastic aspects of evolution of creep damage in austenitic stainless steel. Materials Science and Engineering: A, 527 (18-19). pp. 4810-4817.

Roy, Nilima and Das, Avimanyu and Ray, Ashok K (2015) Simulation and quantification of creep damage. International Journal of Damage Mechanics (IF-1.495).

Roy, Nilima and Ghosh, R N (1997) Modelling effects of specimen size and shape on creep of metals and alloys. Scripta Materialia, 36 (12). pp. 1367-1372.

Roy, Nilima and Ghosh, R N and Bose, S C and Swaminathan, J (2007) A Stochastic Model for Assessment of Creep damage. Exploratory (OLP). CSIR-NML, Jamshdpur. (Submitted)

Roy, Nilima and Ghosh, R N and Dash, Byomkesh and Sivaprasad, S and Tarafder, S (2008) Software development for Critical Assessment of High Temperature Engineering components. Other (TMP). CSIR-NML, Jamshdpur. (Submitted)

Roy, Nilima and Godiwalla, K M and Chaudhuri, S and Ray, Ashok K (2001) Simulation of bond coat properties in thermal barrier coatings during bending. High Temperature Materials and Processes, 20 (2). pp. 103-116.

Roy, Nilima and Guguloth, K and Bagui, Sumanta and Tiwari, Y N and Ray, Ashok K (2013) Damage assessment of service exposed reactor and distill-ation column materials of a petrochemical industry. Engineering Failure Analysis, 28 (IF-0.855). pp. 289-301.

Roy, P K (2018) Creep Rupture Analysis and Life Estimation of 1.25Cr-0.5Mo, 2.25Cr-1Mo and Modified 9Cr-1Mo Steel: A Comparative Study. Journal of The Institution of Engineers (India): Series D, Online .

Roy, P K and Ray, Ashok K and Parida, N (2014) Creep Life Prediction of 1.25Cr-0.5Mo, 2.25Cr - 1Mo and 9Cr-1Mo Steels by accelerated creep rupture tests - A comparative study. [Presentation Slide] (Unpublished)

Roy, Rajat K and Bapari, H and Panda, A K and Mitra, A (2013) Development of high strength stainless steel brazed joints using rapidly solidified filler alloys. Science and Technology of Welding and Joining, 18(3) (IF-1.274). pp. 216-221.

Roy, Rajat K and Das, Swapan K and Panda, A K and Mitra, Amitava (2014) Analysis of Superheater Boiler Tubes Failed through Non-linear Heating. Procedia Engineering, 86 (NIF-0.629). pp. 926-932.

Roy, Rajat K and Panda, A K and Ghosh Chowdhury, S and Mitra, A and Ghosh, R N (2009) Effect of annealing treatment on soft magnetic properties of Fe–6.5 wt% Si wide ribbons. Journal of Magnetism and Magnetic Materials, 321 (18). pp. 2865-2870.

Roy, Sandip and Banerjee, T (1977) Current efficiencies of Ag-Zn alloys under potentiostatic conditions. Surface Technology, 5 (1). pp. 43-48.

Roy, Sandip and Banerjee, T (1975) Phase transformations in electrolytic silver-zinc alloys. Electrodeposition and Surface Treatment, 3 (5-6). pp. 289-305.

Roy, Subrata and Das, Avimanyu (2008) Adverse effects on environment by the Iron Ore Industries - some measures to reduce them. In: Proceedings of National Seminar on Environmental Management in Mining & Allied Industries (EMMA-2008), November 7-8, 2008, BHU, Varanasi.

Roy, Subrata and Das, Avimanyu (2008) Characterization and processing of low-grade iron ore slime from the Jilling area of India. Mineral Processing and Extractive Metallurgy Review, 29 (3). pp. 213-231.

Roy, Subrata and Das, Avimanyu (2009) Nature of low-grade Indian iron ores and the prospects of their enrichment through gravity separation. Minerals & Metallurgical Processing, 26 (3). pp. 141-150.

Roy, Subrata and Venkatesh, A S (2009) Mineralogy and geochemistry of banded iron formation and iron ores from eastern India with implications on their genesis. Journal of Earth System Science, 118 (6). pp. 619-641.

Rudrappa, C and Patil, M R and Rudramuniyappa, M V and Naganoor, P C and Ravi, B P and Chitraki, K (2013) Beneficiation Studies on a Sub Grade Iron Ore Sample Form Barbil Region, Orissa. In: Proceeding of the international on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Rudrappa, C and Patil, M R and Rudramuniyappa1, M V and Naganoor, P C and Ravi, B P and Chitraki, K (2013) Beneficiation Studies on a Sub Grade Iron Ore Sample From Barbil Region, Orissa. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Runyoro, Joseph (2010) Effect of restrained hot spots and integrity of steel welded joints. Journal of Metallurgy and Materials Science, 52 (2). pp. 129-140.

Runyoro, Joseph (2010) The effect of tightening torque on anchor bolts embedded in concrete. Journal of Metallurgy and Materials Science, 52 (1). pp. 67-85.

Rupa, P K P and Chakraborti, P C and Mishra, Suman K (2009) Mechanical and deformation behaviour of titanium diboride thin films deposited by magnetron sputtering. Thin Solid Films, 517 (9). pp. 2912-2919.

Rupa, P K P and Chakraborti, P C and Mishra, Suman K (2014) Structure and indentation behavior of nanocomposite Ti–B–N films. Thin Solid Films, 564 (IF-1.867). pp. 160-169.

Rupa, P K P and Chakrborty, P C and Purnapu, Karuna and Mishra, Suman K (2011) Nanoindentation Studies of Hard Nanocomposite Ti-B-N Thin films. AIP Conference Proceedings, 1393 (3.596 (SCI)). pp. 239-240.

Rupa, P K P and Mishra, Suman K and Pathak, L C and Ghosh, R N (2007) Nanoindentation Studies of TiB2 films. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Russell, J E and Ludgate, B (1958) The Effect of Variation of Ruling Section on the Mechanical Properties of Carburizing Steels. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

S

Sachdeva, S S and Mukherjee, J K and Banerjee, T (1973) Studies on high-temperature oxidation of Ni-Mn alloys. Indian Journal of Technology, 11 (11). pp. 613-616.

Sah, Rameshwar and Dutta, S K and Singh, Vimal and Ghorui, P K (2013) Kinetics and Mechanism of Reduction of Iron Ore-Coal Composite Pellets and Its Usage in Smelting Reduction Process. In: Proceeding of the international conference on science and technology of ironmaking and steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Saha, A K and Khan, Z H and Akerkar, D D (1992) Extraction of nickel from Indian low-grade siliceous ore. Transactions of the Institution of Mining and Metallurgy Section C - Mineral Processing and Extractive Metallurgy , 101 ( ). C52-C56.

Saha, A K and Khan, Z H and Akerkar, D D (1993) Reduction of Manganese sea nodules with noncoking coal. Transactions of the indian institute of metals, 46 (2). pp. 63-69.

Saha, A K and Khan, Z H and Akerkar, D D (1991) Studies on lignite reduction of manganese sea nodules for extraction of nickel, copper and cobalt. Transactions of the Indian Institute of Metals, 44 (2). pp. 131-137.

Saha, A K and Khan, Z H and Premchand, (1999) Reclamation of tungsten metal from tungsten alloy scrap. Transactions of the indian institute of metals, 52 (5). pp. 353-355.

Saha, A K and Shahani, M J and Altekar, V A (1977) Adsorption of cobalt by lignite. Hydrometallurgy, 2 (3). pp. 285-292.

Saha, A K and Srinivasan, S R and Akerkar, D D (1977) Leachability of mosabani and malanjkhand copper ores by microorganisms - comparative-study. Transactions of the Indian Institute of metals, 30 (6). pp. 420-422.

Saha, A K and Srinivasan, S R and Akerkar, D D (1985) Removal of copper and nickel from low grade molybdenite concentrates. NML Technical Journal, 27 (3-4). pp. 40-45.

Saha, Debdulal and Das, Santanu and Sengupta, Kamalendu (2008) Development of commercial nanoporous trace moisture sensor following sol–gel thin film technique. Sensors and Actuators B: Chemical, 128 (2). pp. 383-387.

Sahay, S K and Goswami, B and Kumar, S B and Ray, Ashok K (2007) Fatigue behaviour in titanium-based alloys. Journal of Metallurgy and Materials Science, 49 (2). pp. 97-122.

Sahay, S K and Goswami, B and Ray, Ashok K (2007) Development of cobalt-base alloys for high temperature applications. Journal of Metallurgy and Materials Science, 48 (1). pp. 1-38.

Sahay, S K and Kumar, S B and Goswami, B and Ray, Ashok K (2007) Recent developments in tungsten carbide-cobalt base cemented carbides. Journal of Metallurgy and Materials Science, 49 (3). pp. 143-173.

Sahay, S K and Singh, S K and Goswami, B and Kumar, S B and Ray, Ashok K (2007) Recent development in cobalt-base metallic glasses. Journal of Metallurgy and Materials Science, 48 (2). pp. 59-96.

Sahay, S K and Singh, S K and Goswami, B and Ray, Ashok K (2004) Creep behaviour in Ti-based alloys. High Temperature Materials and Processes, 24 (5). pp. 323-336.

Sahay, S K and Singh, S K and Goswami, B and Ray, Ashok K (2006) Studies of oxidation behavior in Ti-base alloys. Corrosion Reviews , 24 (5). pp. 353-394.

Sahay, S K and Singh, S K and Goswami, B and Ray, Ashok K (2005) Studies of phase transformations in Ti-Al-X alloys. HIGH TEMPERATURE MATERIALS AND PROCESSES , 24 (6). pp. 345-358.

Sahay, S K and Singh, S K and Kumar, S B and Goswami, B and Ray, A K (2006) Recent developments in cobalt base alloys. Journal of Metallurgy and Materials Science, 48 (3). pp. 129-166.

Sahoo, Biraj K and Srivastava, V C and Mahato, B and Ghosh Chowdhury, S (2021) Microstructure-mechanical property evaluation and deformation mechanism in Al added medium Mn steel processed through intercritical rolling and annealing. Materials Science and Engineering A, 799 (IF-). p. 140100.

Sahoo, K L and Das, Samar and Murty, B S (2004) Formation of quasicrystalline related intermetallic compounds in conventionally cast Al-Fe-V-Si alloy. Journal of Non-Crystalline Solids, 334 . pp. 29-32.

Sahoo, K L and Das, Swapan K (2003) Effect of magnesium on sliding wear performance of cast Al-8.3Fe-0.8V-0.9Si alloys. Materials Science and Technology, 19 (7). pp. 959-965.

Sahoo, K L and Das, Swapan K and Murty, B S (2003) Formation of novel microstructures in conventionally cast Al-Fe-V-Si alloys. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing , 355 (1-2). pp. 193-200.

Sahoo, K L and Panda, A K and Das, S and Rao, Venkatesh (2004) Crystallization study of amorphous Al87.5Ni7Mm5Fe0.5 alloy by electrical resistivity measurement. Materials Letters, 58 (3-4). pp. 316-320.

Sahoo, K L and Pathak, B N (2009) Solidification behaviour, microstructure and mechanical properties of high Fe-containing Al–Si–V alloys. Journal of Materials Processing Technology, 209 (2). pp. 798-804.

Sahoo, K L and Poddar, Palash and Das, Goutam and Ravi Kumar, B (2007) Crystallization behaviour and mechanical properties of rapidly solidified Al87.5Ni7Mm5Fe0.5 amorphous alloy. Journal of Materials Science, 42 (16). pp. 6665-6671.

Sahoo, K L and Poddar, Palash and Kumar, Randhir and Pushp, P T (2009) Strain induced melt activation — an effective route to produce high performance alloy plates and sheets. Transactions of the Indian Institute of Metals, 62 (4-5). pp. 275-278.

Sahoo, K L and Rao, Venkatesh and Mitra, A (2003) Crystallization kinetics in an amorphous Al-Ni-Mm-Fe alloy. Materials Transactions , 44 (6). pp. 1075-1080.

Sahoo, K L and Sahu, Rina and Ghosh, M and Chatterjee, S (2008) Studies on crystallization behaviour and mechanical properties of Al-Ni-La metallic glasses. Bulletin of Materials Science, 31 (3). pp. 433-439.

Sahoo, K L and Sahu, Rina and Mitra, A (2007) Kinetic aspects of the nanocrystallization and evolution of microhardness in Al92-XNi8LaX amorphous alloys. Materials and Manufacturing Processes, 22 (4). pp. 497-501.

Sahoo, K L and Sivaramakrishnan, C S (2003) Some studies on Al–8.3Fe–0.8V–0.9Si alloy for near net shape casting. Journal of Materials Processing Technology, 135 (2-3). pp. 253-257.

Sahoo, K L and Sivaramakrishnan, C S and Chakrabarti, A K (2001) The effect of Mg treatment on the properties of Al–8.3Fe–0.8V–0.9Si alloy. Journal of Materials Processing Technology, 112 (1). pp. 6-11.

Sahoo, K L and Sivaramakrishnan, C S and Chakrabarti, A K (2000) Modification of cast structure in Al-8 center dot 3Fe-0 center dot 8V-0 center dot 9Si alloy by magnesium treatment. Materials Science and Technology, 16 (2). pp. 227-230.

Sahoo, K L and Sivaramakrishnan, C S and Chakrabarti, A K (2000) Solidification characteristics of the Al-8.3Fe-0.8V-0.9Si alloy. Metallurgical and Materials Transactions A, 31 (6). pp. 1599-1610.

Sahoo, K L and Sivaramakrishnan, C S and Chakrabarti, A K (2000) Studies on wear characteristics of Al–Fe–V–Si alloys. Wear, 239 (2). pp. 211-218.

Sahoo, K L and Stone, I C (2005) Effect of Si on the formation and stability of the icosahedral quasicrystalline phase in Al-Fe-Cr-Ti alloys. Philosophical Magazine Letters Online ISSN 1362-3036, 85 (5). pp. 231-245.

Sahoo, K L and Wollgarten, M and Haug, J and Banhart, J (2005) Effect of La on the crystallization behaviour of amorphous Al94 − xNi6Lax (x = 4–7) alloys. Acta Materialia, 53 (14). pp. 3861-3870.

Sahoo, K L and Wollgarten, M and Kim, K B and Banhart, J (2005) Crystallization behavior and microhardness evolution in Al92-xNi8Lax amorphous alloys. Journal of Materials Research, 20 (11). pp. 2927-2933.

Sahota, N S and Gupta, K N and Ram, Mohan (1987) Kinetics and mechanism of reoxidation behavior of solid reductant based direct reduced iron. Transactions of the Indian Institute of metals, 40 (5). pp. 415-422.

Sahu, J K (2008) Effect of 475oC embrittlement on the fatigue behaviour of a duplex stainless steel. PhD thesis, University Siegen.

Sahu, J K and Das, D K and Nandy, T K and Mandal, D and Rajnikanth, V and Swaminathan, J and Ray, Ashok K (2011) Effect of titanium aluminide coating on cyclic plastic deformation and fatigue life of a titanium alloy at 600 °C. Materials Science and Engineering A, 530 . pp. 664-668.

Sahu, J K and Ghosh, R N and Christ, H J (2009) Low cycle fatigue behaviour of duplex stainless steel: influence of isothermal aging treatment. Fatigue & Fracture of Engineering Materials & Structures, 33 (2). pp. 77-86.

Sahu, J K and Gupta, R K and Swaminathan, J and Paulose, N and Mannan, S L (2013) Influence of hot Corrosion on Low Cycle fatigue behavior of Nickel base Superalloy SU 263. International Journal of Fatigue, 51 (IF-1.976). pp. 68-73.

Sahu, J K and Krupp, U and Christ, H J (2012) Fatigue crack initiation behavior in embrittled austenitic–ferritic stainless steel. International Journal of Fatigue, 45 . pp. 8-14.

Sahu, J K and Krupp, U and Ghosh, R N and Christ, H J (2009) Effect of 475 °C embrittlement on the mechanical properties of duplex stainless steel. Materials Science and Engineering: A, 508 (1-2). pp. 1-14.

Sahu, J K and Ravi Kumar, B and Das, S K and Paulose, N and Mannan, S L (2015) Isothermal high temperature low cycle fatigue behavior of Nimonic-263: Influence of type I and type II hot corrosion. Materials Science and Engineering A, 622 (IF-2.409). pp. 131-138.

Sahu, J K and Sahu, K K and Ray, A K (2012) The influence of high-temperature oxidation resistant titanium aluminide coating on low-cycle fatigue behaviour of titanium alloy IMI 834 at 600 C. Institute of Mechanical Engineers, 226 . pp. 35-41.

Sahu, J K and Sahu, K K and Ray, Ashok K (2011) The influence of high-temperature oxidation resistant titanium aluminide coating on low-cycle fatigue behaviour of titanium alloy IMI 834 at 600°C. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, October 31, 2011 1464420711425133, 226 (L1). pp. 34-41.

Sahu, J K and Singh, S R and Das, Samar and Sivaprasad, S and Tarafder, S and Ghosh, R N (2006) Deformation mechanism in a single phase austenitic and ferrito-austenitic stainless steel. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Sahu, J K and Swaminathan, J and Sivaprasad, S and Ray, Ajoy K and Tarafder, S and Chaudhuri, S and Ghosh, R N (2008) Use of expert system software for life monitoring of power plant components. In: Remaining Life Assessment of aged Components in Thermal Power Plants & Petrochemical Industries. NML, Jamshedpur, India, Jamshedpur, pp. 169-181. ISBN 81-87053-73-1

Sahu, K K (2002) Hydrothermal Synthesis and Microstructural Control of Hematite Particles. In: Proceedings of the Indo-Malaysian Joint Workshop(WAM-2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Sahu, K K and Agrawal, A and Pandey, B D (2005) Nickel recovery from spent nickel catalyst. Waste Management & Research, 23 (2). pp. 148-154.

Sahu, K K and Agrawal, A and Pandey, B D (2004) Recent trends and current practices for secondary processing of zinc and lead. Part II: zinc recovery from secondary sources. Waste Management & Research, 22 (4). pp. 248-254.

Sahu, M K and Palit Sagar, S (2021) Nonlinearity in the propagation of acoustic waves: Simulation and experimental validation in a creep damaged material. Materials Today, 44, Part 1 . pp. 2251-2256.

Sahu, Puspendu and Hamada, A S and Ghosh, R N and Karjalainen, L P (2007) X-ray Diffraction Study on Cooling-Rate-Induced γfcc→εhcp Martensitic Transformation in Cast-Homogenized Fe-26Mn-0.14C Austenitic Steel. Metallurgical and Materials Transactions A, 38 (9). pp. 1991-2000.

Sahu, Puspendu and Hamada, A S and Ghosh Chowdhury, S and Karjalainen, L P (2007) Structure and microstructure evolution during martensitic transformation in wrought Fe-26Mn-0.14C austenitic steel: an effect of cooling rate. Journal Of Applied Crystallography, 40 (2). pp. 354-361.

Sahu, Puspendu and Shee, S K and Hamada, A S and Rovatti, L and Sahu, T and Mahato, B and Ghosh Chowdhury, S and Porter, D A and Karjalainen, L P (2012) Low strain rate deformation behavior of a Cr-Mn austenitic steel at -80oC. Acta Materialia, 60(2012) . pp. 6907-6919.

Sahu, Puspendu and Singh, S R and Mahato, B and Ghosh Chowdhury, S and Ravi Kumar, B and Das, Swapan K and Ghosh, R N (2007) y-y' Lattice misfit and its influence on the microstru-cture of UDIMET 520 during the rejevenation heat treatment : an X-ray diffraction study. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Sahu, Ranjan K (2006) Effect of Mo doping on magnetic and transport properties of La0.5Sr0.5CoO3. Journal of Magnetism and Magnetic Materials, 305 (1). pp. 47-52.

Sahu, Ranjan K and Ganguly, Koustav and Mishra, T and Mishra, M and Ningthoujam, R S and Roy, S K and Pathak, L C (2012) Stabilization of intrinsic defects at high temperatures in ZnO nanoparticles by Ag modification. Journal of Colloid and Interface Science, 366 (1). pp. 8-15.

Sahu, Ranjan K and Krishnan, P S R and Das, A and Shinde, A B and Ramanasham, M (2006) Ru-induced spin rotation in La1.2Sr1.8Mn1.9Ru0.1O7 bilayered manganite. Journal of Magnetism and Magnetic Materials, 297 (2). pp. 84-87.

Sahu, Ranjan K and Mohanta, Ojaswini and Pramanick, A K (2012) XPS study on the correlation of magnetic properties and site occupancy of Al doped SrFe12O19. Journal of Alloys and Compounds, 532 . pp. 114-120.

Sahu, Ranjan K and Pandey, S K and Pathak, L C (2011) Valence and origin of metal-insulator transition in Mn doped SrRuO3 studied by electrical transport, X-ray photoelectron spectroscopy and LSDA plus U calculation. Journal of Solid State Chemistry, 184 (3). pp. 523-530.

Sahu, Ranjan K and Ray, Ashok K and Das, Swapan K and Kailath, A J and Pathak, L C (2006) Microwave-assisted combustion synthesis of Ni powder using urea. Journal of Materials Research, 21 (7). pp. 1664-1673.

Sahu, Ranjan K and Roy, Ajoy K and Manotiaran, S S and Arora, S and Mishra, T and Lim, S -H and Salamanca-Riba, L G and Kundaliya, D C and Panda, A K and Mitra, A and Pathak, L C (2008) Single step synthesis of Ni wire, sponge and flower, and their magnetic properties. Magnetic Materials Book Series: Aip Conference Proceedings, 1003 . pp. 100-102.

Sahu, Rina and Gangopadhyay, A K and Kelton, K F and Chatterjee, S and Sahoo, K L (2009) Room temperature ageing of Al–Ni–RE (RE = La, Gd, Er) metallic glasses. Scripta Materialia, 61 (6). pp. 588-591.

Sahu, Rina and Kailath, A J and Chatterjee, S and Sahoo, K L (2010) Effect of La content on the room temperature ageing behavior of Al90−xNi6La4+x (x = 0–3) metallic glasses. Materials Science and Engineering: A, 527 (6). pp. 1339-1342.

Sahu, S C and Samantara, A K and Dash, A and Juluri, R R and Sahu, Ranjan K and Mishra, B K and Jena, B K (2013) Graphene-induced Pd nanodendrites: A high performance hybrid nanoelectrocatalyst. Nano Research, 6/9 . pp. 635-643.

Sahu, S K and Razi, M K and Beuscher, M and Chagnes, A (2020) Recovery of Metal Values from Ni-Cd Cake Waste Residue of an Iranian Zinc Plant by Hydrometallurgical Route. Metals, 10(5) . p. 655.

Sahu, S K and Verma, V K and Bagchi, D and Kumar, Vinay and Pandey, B D (2008) Recovery of chromium(VI) from electroplating effluent by solvent extraction with tri-n-butyl phosphate. Indian Journal Of Chemical Technology, 15 (4). pp. 397-402.

Saleem, Sheikh shahid and Nigam, S P (2005) Noise prediction model for Indian traffic conditions using L10 approach. Journal of Metallurgy and Materials Science, 47 (2). pp. 91-101.

Saleem, Sheikh shahid and Nigam, S P (2003) Regression analysis for selection of a noise descriptor to accurately predict traffic noise on Indian highways. Journal of Metallurgy and Materials Science, 45 (3). pp. 127-135.

Samal, S and Mukherjee, P S and Ray, Ajoy K (2010) Comparative Study on Energy Consumption and Yield by Various Thermal Plasma Routes for Production of Titania slag. Plasma Chemistry and Plasma Processing, 30 (3). pp. 413-428.

Samanta, Salkat and Goswami, M C and Baidya, T K and Mukherjee, S and Dey, R (2013) Mineralogy and carbothermal reduction behaviour of vanadium-bearing titaniferous magnetite ore in Eastern India. International Journal of Minerals Metallurgy and Materials, 20(10) (IF-0.483). pp. 917-924.

Samanta, Shipra and Misra, R N and Bhatnagar, P P (1968) Studies on the extraction of nickel from the nickeliferous laterites of Badampahar area, Orissa. NML Technical Journal, 10 (2). pp. 15-18.

Samantaray, S K and Mishra, T and Parida, K M (2000) Studies on anion promoted Titania 2: Preparation, characterisation and catalytic activity towards aromatic alkylation over sulfated titania. Journal of Molecular Catalysis A: Chemical , 156 . pp. 267-274.

Sankar, M and Batra, N K and Shekhar, R and Mehrotra, S P (2006) Roasting, reduction and leaching of an Indian ilmenite ore for producing synthetic rutile. Transactions Of The Indian Institute Of Metals , 59 (3). pp. 381-387.

Sankara Narayanan, T S N and Seshadri, S K (2009) Recent Advances In Surface Treatment And Electrodeposition. Corrosion Reviews , sp. Iss.sl suppl . pp. 533-600.

Sankara Rao, K Bhanu and Nagesha, A (2001) Significance of Creep-Fatigue Interactions in Strctural Integrity Assessment. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. NML, Jamshedpur, India, Jamshedpur, pp. 164-184. ISBN 81-87053-62-3

Santosh, Sachin and Shukla, A K (2013) Data Based Modeling Approach to Iron and Steel Making Processes. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking , December 16-18, 2013, CSIR-NML Jamshedpur.

Sanyal, D (1995) Boundary-element formalism for simulation of unsteady heat-transfer in welding. Transactions of The Indian Institute of Metals , 48 (3). pp. 189-192.

Sanyal, D (1995) A boundary-element formalism for simulation of unsteady heat-transfer in welding. Transactions of the indian institute of metals, 48 (3). pp. 189-192.

Sanyal, P and Gupta, K K and Pandey, L P (1978) Standard reference materials of low-alloy steels. Research and Industry, 23 (3). pp. 143-145.

Sanyal, P and Rajeev, and Gupta, K K (1977) Comprehension methods of chemical analysis of low alloy steel. NML Technical Journal, 19 (3-4). pp. 47-51.

Saray, O and Purcek, G and Mahato, B and Ghosh Chowdhury, S (2012) Texture evolution of IF-steel sheets processed by equal-channel angular sheet extrusion (ECASE). Materials Science Forum, 702-703 . pp. 123-126.

Sarkar, A N and Singha, K and Panda, Asit Baran and Pal, Sagar (2021) In-situ deposited CdS NPs on pH induced fully exfoliated layered titanate-biopolymeric composite and its photocatalytic activity. Polymer, 225 (IF-4.). p. 123791.

Sarkar, B and Dalal, Biswajit and Ashok, V D and Chakrabarti, Kaushik and Mitra, A and De, S K (2014) Magnetic properties of mixed spinel BaTiO3-NiFe2O4 composites. Journal of Applied Physics, 115(12) (IF- 2.185).

Sarkar, B and Das, Avimanyu (2010) A comparative study of slip velocity models for the prediction of performance of floatex density separator. International Journal of Mineral Processing, 94 (1-2). pp. 20-27.

Sarkar, M K (1994) Heat Treatment of Forgings. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Sarkar, Partha and Mohanta, Ojaswini and Pal, S K and Panda, A K and Mitra, A (2010) Magneto-Impedance behavior of Co-Fe-Nb-Si-B-based ribbons. Journal of Magnetism and Magnetic Materials, 322 (8). pp. 1026-1031.

Sarkar, Partha and Roy, Rajat K and Mitra, A and Panda, A K and Churyukanovaa, Margarita and Kaloshkina, Sergey (2012) Effect of Nb and Cr incorporation on the structural and magnetic properties of rapidly quenched FeCoSiB microwires. Journal of Magnetism and Magnetic Materials, 324 (16). pp. 2543-2546.

Sarkar, Rahul and Gupta, Pramod and Ballal, N B (2013) Refining of metal droplet in slag using the concept of Gibbs’ Free Energy Minimization at the slag-metal interface. In: Proceedings of The International Conference on Science and Technology of Ironmaking and Steelmaking, Decmber 16-18, 2013, CSIR-NML, JSR.

Sarma, D S (1994) Cold Work and Hot work Tool Steels. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Sarma, D S (1994) Microstructural Constituents in Steels. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Sasikumar, C and Rao, D S and Srikanth, S and Ravi Kumar, B and Mukhopadhyay, N K and Mehrotra, S P (2004) Effect of mechanical activation on the kinetics of sulfuric acid leaching of beach sand ilmenite from Orissa, India. Hydrometallurgy, 75 (1-4). pp. 189-204.

Sasikumar, R and Arunachalam, R M (2010) Production of nanomaterials through machining. Journal of Metallurgy and Materials Science, 52 (2). pp. 141-147.

Sastry, G V S and Rao, V V and Ramachandrarao, P (1986) A new quasi-crystalline phase in rapidly solidified Mg4CuAl6. Scripta Metallurgica, 20 (2). pp. 191-193.

Sastry, P R and Bhandary, V S and Gupte, P K and Nijhawan, B R (1967) Shell moulding with indigenous raw materials. NML Technical Journal, 9 (1). pp. 29-34.

Satendra, Kumar and Sankara Narayanan, T S N and Sundara Raman, Ganesh (2010) Corrigendum to “Thermal oxidation of CP-Ti: Evaluation of characteristics and corrosion resistance as a function of treatment time” [Mater. Sci. Eng., 29 (2009) 1942–1949]. Materials Science and Engineering: C, 30 (2). p. 330.

Satendra, Kumar and Sankara Narayanan, T S N and Sundara Raman, Ganesh and Seshadri, S K (2010) Fretting corrosion behaviour of thermally oxidized CP-Ti in Ringer’s solution. Corrosion Science, 52 (3). pp. 711-721.

Satendra, Kumar and Sankara Narayanan, T S N and Sundara Raman, Ganesh and Seshadri, S K (2010) Surface modification of CP-TI to improve the fretting corrosion resistance: Thermal oxidation vs. anodizing. Materials Science and Engineering: C, 30 (6). pp. 921-927.

Satendra, Kumar and Sankara Narayanan, T S N and Sundara Raman, Ganesh and Seshadri, S K (2010) Evaluation of fretting corrosion behaviour of CP-Ti for orthopaedic implant applications. Tribology International, 43 (7). pp. 1245-1252.

Satendra, Kumar and Singh, K K and Ramachandrarao, P (2001) Effects of fly ash additions on the mechanical and other properties of porcelainised stoneware tiles. Journal of Materials Science, 36 (24). pp. 5917-5922.

Satendra, Kumar and Sivakumar, B and Sankara Narayanan, T S N and Sundara Raman, Ganesh and Seshadri, S K (2010) Fretting-corrosion mapping of CP-Ti in Ringer's solution. Wear, 268 (11-12). pp. 1537-1541.

Sathiyamurthy, S and Thaheer, A S A and Jayabal, S (2012) Modelling and optimization of mechanical properties of Al2O3-coir-polyester composite using regasse surface methology. Journal of Metallurgy and Materials Science, 54(4) . pp. 303-310.

Satyanarayana, N V and Mall, R and Pal, A (1996) A layered architecture for real-time systems. Microprocessors and Microsystems, 20 (4). pp. 241-250.

Sau, D C and Banerjee, A and Kumar, Manoj and Kumar, Rakesh (2015) Experimental investigation for conversion of hematite to magnetite with high ash Jhama Coal. Journal of Metallurgy and Materials Science, 57(2) . pp. 83-91.

Sau, D C and Das, Suchandan K and Bandyopadhyay, D (2013) A Mathematical Model of The Raceway for Real time Application to an Operating Blast Furnace with Pulverized Coal Injection. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Sau, D C and Das, Suchandan K and Bandyopadhyay, D and Mandal, G K (2018) A reduced order mathematical model of the blast furnace raceway with and without pulverized coal injection for real time plant application. International Journal of Modelling and Simulation, online . pp. 1-12.

Sau, D C and Mohanty, Swati and Biswal, K C (2010) Experimental studies and empirical models for the prediction of bed expansion in gas–solid tapered fluidized beds. Chemical Engineering and Processing: Process Intensification, 49 (4). pp. 418-424.

Sau, D C and Mohanty, Swati and Biswal, K C (2008) Minimum fluidization velocity at elevated temperature in tapered fluidized bed. Chemical Engineering and Processing: Process Intensification, 47 (2008). pp. 2391-2394.

Schulz, A and Srivastava, V C and Uhlenwinkel, V and Bauckhage, K (2004) Spray forming of 2014-Al alloy based composites with injection of SiC particulates. Zeitschrift Fur Metallkunde , 95 (9). pp. 763-768.

Scott, D (1966) Substitute alloys as bearing materials. NML Technical Journal, 8 (1). pp. 25-30.

Scott, D (1966) Substitute Alloys as Bearing Materials. NML Technical Journal, 8 (1). pp. 24-30.

Scott, D (1965) Techniques for the study of micro-phases and their influence on material properties. NML Technical Journal, 7 (1). pp. 32-40.

Sekhar, K C and Gupta, K K and Bhattacharjee, S and Chakravarty, S (2004) The determination of gold in ore samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Spectrochimica Acta Part B Atomic Spectroscopy, 25 (4). pp. 165-169.

Sekhar, K C and Subramanian, S and Modak, J M and Natarajan, K A (1998) Removal of metal ions using an industrial biomass with reference to environmental control. International Journal of Mineral Processing, 53 (1-2). pp. 107-120.

Selvam, S T and Chaudhuri, S and Das, Arpan and Dhara, S and Das, T P and Singh, U K (2013) Improving Productivity of Sinter Through Magnetic Segregation Chute at Sinter Plant, Bokaro Steel Plant, Bokaro Steel Plant. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Sen, Mainak and Suman, Swati and Mukherjee, Shreya and Banerjee, Trideep and Sivaprasad, S and Tarafder, S and Bhattacharjee, Amit and Kar, Sujoy (2021) Low cycle fatigue behavior and deformation mechanism of different microstructures in Ti-5Al-5Mo-5V-3Cr alloy. International Journal of Fatigue, 148 (IF-4.369 ). p. 106238.

Sen, P and Misra, D D (1972) The problem of the Iron Ore Fines in India. NML Technical Journal, 14 (2). pp. 47-55.

Sen, P K (1965) Apparent activation of energy decarbonisation of Fe-C melts. NML Technical Journal, 7 (4). pp. 17-19.

Sen, S (2007) Preparation and Evaluation of Structural, Microstructural and Electrical Properties of Polymer-Ceramic Composite. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Sen, S and Chakraborty, N and Rana, P and Sahu, Ranjan K and Singh, S and Panda, A K and Tripathy, S and Pradhan, D K and Sen, A (2016) Effect of Ti doping on the structural, electrical and magnetic properties of GaFeO3. Journal of Materials Science: Materials in Electronics, 27(5) (IF-2.019). pp. 4647-4652.

Sen, S and Choudhary, R N P (2007) Dielectric relaxation in Sr modified PST ceramics. Applied Physics A: Materials Science & Processing, 87 (4). pp. 727-731.

Sen, S and Choudhary, R N P (2008) Phase transition in Sr modified Pb(SnTi)O3 system. Journal of Alloys and Compounds, 457 (1-2). pp. 417-421.

Sen, S and Choudhary, R N P and Pramanick, P (2007) Structural and electrical properties of Ca2+-modified PZT electroceramics. Physica B: Condensed Matter, 387 (1-2). pp. 56-62.

Sen, S and Choudhary, R N P and Tarafder, A and Pramanik, P (2006) Impedance spectroscopy study of strontium modified lead zirconate titanate ceramics. Journal of Applied Physics , 99 (12). pp. 124114-124118.

Sen, S and Das, Swapan K and Mishra, Suman K and Tarafder, A (2007) Low-temperature synthesis of 0.65 PbMg1/3Nb2/3O3-0.35PbTiO(3) ceramics. Journal of the American Ceramic Society, 90 (8). pp. 2634-3638.

Sen, S and Mishra, Suman K (2008) Electrical behaviour of PMN–PT–PVDF nanocomposite. Journal of Physics D: Applied Physics, 41 (16). p. 165305.

Sen, S and Mishra, Suman K and Palit Sagar, S and Das, Swapan K (2008) Preparation and characterization of PMN-PT nanocomposite. Indian Journal Of Engineering And Materials Sciences , 15 (2). pp. 111-115.

Sen, S and Mishra, Suman K and Palit Sagar, S and Das, Swapan K and Tarafder, A (2008) Impedance analysis of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 ceramic. Journal of Alloys and Compounds, 453 (1-2). pp. 395-400.

Sen, S and Panda, A K and Prasad, K (2012) Magnetic and electric behavior of NiFe204-PVDF nanocomposites. Material Science-Poland, 30 . pp. 415-425.

Sen, S and Saha, P and Prasad, K (2010) A novel technique for the synthesis of CaCu3Ti4O12 ceramics. Materials Science-Poland, 28 (1). pp. 265-271.

Sengupta, B and Chatterjee, S and Rott, U and Kauffman, H and Bandopadhyay, A and DeGroot, W and Nag, N K and Carbonell-Barrachina, A A and Mukherjee, Surojit (2009) A simple chemical free arsenic removal method for community water supply – A case study from West Bengal, India. Environmental Pollution, 157 (12). pp. 3351-3353.

Sengupta, P L and Sinha, P K and Aush, S C (1994) Removal of potassium from the electrolyte in the production process for electrolytic manganese-dioxide. Transactions of the Indian Institute of Metals, 47 (5). pp. 339-341.

Sengupta, Vivek (2011) Effect of Severe Plastic Deformation by High Pressure Torsion Process on Aluminium 6082 alloy. Training Report (TR). National Metallurgy Laboratory, Jamshedpur. (Submitted)

Senk, Dieter (2013) Continuous Casting - Continuous Development. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Seshu Kumar, A and Ravi Kumar, B and Datta, G L and Ranganath, V R (2010) Effect of microstructure and grain size on the fracture toughness of a micro-alloyed steel. Materials Science and Engineering: A, 527 (4-5). pp. 954-960.

Seth, P P and Das, Arpan and Bar, H N and Sivaprasad, S and Basu, A and Dutta, K (2015) Evolution of Dislocation Density During Tensile Deformation of BH220 Steel at Different Pre-strain Conditions. Journal of Materials Engineering and Performance, 24(7) (IF-0.998). pp. 2779-2783.

Sethi, Ankit S and Mahobia, G S and sinha, O P (2015) Reduction behavior of iron ore pellets with addition of plastics along with conventional reducing agents. Journal of Metallurgy and Materials Science, 57(3) . pp. 167-171.

Sewell, J F (1958) The Molybdenum-Boron Structural Steel. In: Symposium on Production, Properties, and Applications of Alloy and Special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Shah, Minal and Das, Suchandan K (2018) An Artificial Neural Network Model to Predict the Bainite Plate Thickness of Nanostructured Bainitic Steels Using an Efficient Network-Learning Algorithm. Journal of Materials Engineering and Performance . pp. 1-11. (In Press)

Shah, Minal and Roy, S and Sahu, Rina (2014) Production of perfect sinter-Need for blast furnaces. Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 223-229.

Shah, Minal and Sahoo, K L and Das, Swapan K and Das, Goutam (2020) Wear Mechanism of High Chromium White Cast Iron and Its Microstructural Evolutions During the Comminution Process. Tribology Letters, 68(3) (IF-2.566).

Shahani, M J (1981) Biohydrometallurgy in India 1980–1981 — A brief round-up. Hydrometallurgy, 7 (4). pp. 375-380.

Shahani, M J (1983) Biohydrometallurgy in india 1982 - a brief round up. Hydrometallurgy, 10 (2). pp. 257-261.

Shahani, M J and Saha, A K and Altekar, V A (1979) Multiple-stage extraction of nickel from ammoniacal solutions by adsorption on lignite. Transactions of the institution of mining and metallurgy section C-mineral processing and extractive metallurgy, 88 (March). C51- C52.

Shakhtshneider, T P and Myz, S A and Dyakonova, M A and Boldyrev, V V and Nizovskii, A L and Kalinkin, A V and Kumar, Rakesh (2011) Mechanochemical Preparation of Organic-Inorganic Hybrid Materials of Drugs with Inorganic Oxides. Acta Physica Plolonica, 120 (2). pp. 272-278.

Shamsuddin, M and Gupta, T K S P and Nasar, A and Ramachandrarao, P (1994) Thermodynamic behavior of zinc and cadmium in liquid-Te-saturated CDTE-ZNTE solid-solutions. Thermochimica Acta , 246 (1). pp. 213-227.

Shamsuddin, M and Gupta, T K S P and Nasar, A and Ramachandrarao, P (1994) Thermodynamic behaviour of zinc and cadmium in liquid-Te-saturated CdTe---ZnTe solid solutions. Thermochimica Acta, 246 (1). pp. 213-227.

Shanmuganathan, P and Ravishankar, G S and Kamesh, S V (2008) Boiler feed pump foundation bolts failures. In: Remaining Life Assessment of aged Components in Thermal Power Plants & Petrochemical Industries. NML, Jamshedpur, India, Jamshedpur, pp. 77-84. ISBN 81-87053-73-1

Sharan, R and Saksena, N P and Prasad, R (1975) Problems of wear in forging dies. NML Technical Journal, 17 (1-2). pp. 10-14.

Sharma, C and Pramanik, S (1971) Some observations on isothermal ageing behaviour of wrought Al-Mg-Si alloys. NML Technical Journal, 13 (3). pp. 80-82.

Sharma, Geetanjali (2012) Comparative Study on Biomimetically Synthesized Ferrofluid at different pH and Concentration. Masters thesis, Utkal University BBSR.

Sharma, Jyoti and Sharma, T (2013) Making of Ferro Coke from Low Volatile Coking Coal. In: Proceeding of the International Conference of Science and Technology of Ironmaking and Steelmaking , December 16-18, 2013, CSIR-NML Jamshedpur.

Sharma, Mamta and Bhowmik, Tishrota and Mishra, V (2021) Significance of washability on heat-altered coal from Jharia and Raniganj Coalfields, India. International Journal of Oil, Gas and Coal Technology, 27(2) . pp. 169-185.

Sharma, R and Bose, S K (1982) Using lattice parameter to estimate activation energy. NML Technical Journal, 24 (3-4). pp. 28-30.

Sharma, S and Azad, S C and Khan, Md Soaib and Ranjan, R and Behera, Banarji and Choudhura, R N P (2014) Effect of Gd3+-substitution on structural and electrical properties of lead zirconate titanate (PZT; Zr/ Ti = 55/45) ceramics. Journal of Metallurgy and Materials Science, 56(2) (NON-SCI). pp. 137-142.

Sharma, S and Khan, Md Soaib and Ranjan, Rajeev and Choudhary, R N P (2015) Energy material Sm3+-modified lead zirconate titanate (PZT) ceramics : preparation, characterisation and application. Journal of Metallurgy and Materials Science, 57(3) . pp. 151-155.

Sharma, S and Mukherjee, T (1977) Structure and creep properties of commercial heats of 2¼ Cr-I Mo steel made in TISCO in comparison with international standards. NML Technical Journal, 19 (1). pp. 8-14.

Sharma, S C and Girish, B M and Kamath, Rathnakar and Satish, B M (1998) An Evaluation of the sliding Wear Behaviour of SiC Particles Reinforced Copper Alloy Composite Materials. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 72-82.

Sharma, S C and Girish, B M and Kulkarni, R S and Kamath, R (1996) Machinability of zinc alloy based particulate metal matrix composites. NML Technical Journal, 38 (3). pp. 107-111.

Sharma, S C and Girish, B M and Ramachandrarao, P (1996) Tribological properties of zinc alloy based composites for bearing applications. NML Technical Journal, 38 (2). pp. 73-76.

Sharma, S R (1994) Forging Technology - As Applied to Automobile Industry. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Sharma, T and Sharma, Jyoti (2013) Firing Schedule for Goethitic Iron Ore Pellets. In: Proceeding of the International conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Shavrin, S V and Shenouda, F N and Sherif, S A (1962) Process-Analysis of the Reduction of Ores and Sintered Material as a Function of Time. NML Technical Journal, 4 (3). pp. 18-21.

Sheikh, Lubna (2012) Study of Novel Nanomagnetic Hydroxyapatite as a Potent Biomedical System. Masters thesis, NOU, Orissa.

Sheikh, Lubna and Dutta, Abinash and Chandra, R and Nayar, S (2015) Effect of Ferrofluids on Microbes. International Journal of New Technologies in Science and Engineering, 2(3) . pp. 109-117.

Sheikh, Lubna and Mahto, Neha and Nayar, S (2015) In situ synthesis of hydroxyapatite nanocomposites using iron oxide nanofluids at ambient conditions. Journal of Materials Science: Materials in Medicine, 26(1) (IF-2.379). p. 5393.

Sheikh, Lubna and Vohra, R and Verma, A K and Nayar, S (2015) Biomimetically Synthesized Aqueous Ferrofluids Having Antibacterial and Anticancer Properties. Materials Sciences and Applications, 6 . pp. 242-250.

Shukla, M K and Nigam, Vineeta and Singh, Harjeet and Setua, D K and Mathur, G N (1998) Lignin Reinforced Rubber Composites. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 233-245.

Shukla, R and Das, Swapan K and Ravi Kumar, B and Ghosh, S K and Kundu, S and Chatterjee, S (2012) An Ultra-low Carbon, Thermomechanically Controlled Processed Microalloyed Steel: Microstructure and Mechanical Properties. Metallurgical and Materials Transactions A, 43 (12). pp. 4835-4845.

Shuvaeva, E and Kaloshkin, S and Churyukanovaa, Margarita and Perminov, A and Khriplivets, I and Mitra, A and Panda, A K and Roy, Rajat K and Murugaiyan, Premkumar and Zhukova, V and Zhukov, A (2018) The impact of bending stress on magnetic properties of finemet type microwires and ribbons. Journal of Alloys and Compounds, 743 (IF-3.133). pp. 388-393.

Shyam, A K (1984) Botanical investigations in singhbhum copper belt. Journal of the geological society of India, 25 (5). pp. 303-304.

Shyamsunder, M T (2011) Advances in Electromagnetic NDE and its Applications to the steel and allied industries. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Siddique, A B and Singh, V P and Pramanick, A K and Ray, M (2020) Amorphous carbon dot and chitosan based composites as fluorescent inks and luminescent films. Materials Chemistry and Physics, 249 (IF-3.408).

Sing, S B and Ray, S and Gupta, R K and Bhatnakar, N S (1998) Influence of Anisotropy on Creep in a Whisker Reinforced MMC Rotating Disc. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 83-102.

Singh, A and Singh, B P and Wani, M R and Kumar, D and Singh, J K and Singh, Vakil (2013) Effect of anodization on corrosion behaviour and biocompatibility of Cp-titanium in simulated body fluid. Bulletin of Materials Science, 36(5) (IF-0.584). pp. 931-937.

Singh, B N (1970) Silver as catalyst. NML Technical Journal, 12 (3). pp. 83-85.

Singh, B N and Mohanty, B N and Akerkar, D D and Altekar, V A (1982) Extraction of nickel and cobalt from the nickeliferous oxide ores of India. Transactions of The Indian Institute of Metals, 35 (4). pp. 357-365.

Singh, B P and Singh, Ratnakar (1997) Investigation on the effect of ultrasonic pretreatment on selective separation of iron values from iron ore tailings by flocculation. Separation Science and Technology, 32 (5). pp. 993-1002.

Singh, Brijpal (2017) Correlation of inclusion characteristics and microstructure with mechanical properties in low carbon steel weldments. Journal of Metallurgy and Materials Science, 59(3) . pp. 117-125.

Singh, C B and Gupta, R N and Vaish, A K and Singh, S D and Goswami, N G (2014) Ancient iron making from lean grade ores in India - An introspection. Journal of Metallurgy and Materials Science , 56(2) (NON-SCI). pp. 93-105.

Singh, C B and Gupta, R N and Vaish, A K and Goswami, M C (2015) Reduction kinetics of low grade iron ore - revealing the efficacy of ancient iron making process. Journal of Metallurgy and Materials Science, 57(3) . pp. 127-134.

Singh, D D N (1998) Awareness of corrosion problems can save millions: Economical impact of corrosion inhibitors. Transactions of the indian institute of metals, 51 (5). pp. 291-301.

Singh, D D N (1985) Passivation behavior of titanium-6al-4v alloy in phosphoric-acid solution. Journal of the electrochemical society (JES), 132 (2). pp. 378-381.

Singh, D D N and Banerjee, M K (1986) Corrosion behavior of nickel in methanol. Corrosion Science, 42 (3). pp. 156-161.

Singh, D D N and Bhattacharya, D (2010) Performance and mechanism of action of self-priming organic coating on oxide covered steel surface. Progress in Organic Coatings, 68 (1-2). pp. 62-69.

Singh, D D N and Bhattacharya, D (2010) Performance and mechanism of action of self-priming organic coating on oxide covered steel surface. Progress in Organic Coatings, 67 (2). pp. 129-136.

Singh, D D N and Dey, A K (1989) Corrosion behaviour of 304 stainless steel in dioxane. NML Technical Journal, 31 (1-4). pp. 24-27.

Singh, D D N and Dey, A K and Dey, M and Singh, B K (1998) Corrosion characteristics of HSLA steels in sea water. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, D D N and Dey, A K and Khan, I (1998) Passivation of galvanized surfaces to improve their corrosion resistance. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India, .

Singh, D D N and Dey, M and Singh, V (2002) Role of buffering and complexing agents in zinc plating chloride baths on corrosion resistance of produced coatings. Corrosion, 58 (11). pp. 971-980.

Singh, D D N and Dey , A K (1993) Synergistic effects of inorganic and organic cations on inhibitive performance of propargyl alcohol on steel dissolution in boiling hydrochloric-acid solution. Corrosion , 49 (7). pp. 594-600.

Singh, D D N and Gaur, B (1995) Improving the inhibitive performance of dibenzyl sulfoxide for pickling of steel in sulfuric-acid. Corrosion, 51 (8). pp. 593-601.

Singh, D D N and Ghosh, Rita (2006) Electroless nickel–phosphorus coatings to protect steel reinforcement bars from chloride induced corrosion. Surface and Coatings Technology, 201 (1-2). pp. 90-101.

Singh, D D N and Ghosh, Rita (2008) Molybdenum–phosphorus compounds based passivator to control corrosion of hot dip galvanized coated rebars exposed in simulated concrete pore solution. Surface and Coatings Technology, 202 (19). pp. 4687-4701.

Singh, D D N and Ghosh, Rita (2005) Unexpected deterioration of fusion-bonded epoxy-coated rebars embedded in chloride-contaminated concrete environments. Corrosion Science, 61 (8). pp. 815-829.

Singh, D D N and Singh, B K (1998) Effect of mixed cations on phosphate coating of steel. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, D D N and Yadav, Shyamjeet (2008) Role of tannic acid based rust converter on formation of passive film on zinc rich coating exposed in simulated concrete pore solution. Surface and Coatings Technology, 202 (8). pp. 1526-1542.

Singh, H P and Misra, S S and Leach, J S L (1980) Enthalpy effects in quaternary liquid woods alloy. Philosophical magazine A-Physics of condensed matter structure defects and mechanical properties, 41 (1). pp. 9-20.

Singh, Inder (1998) Atmospheric corrosion of 18 years study. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, Inder (1970) Effect of inhibitors on the permeability and diffusion co-efficient of hydrogen in steel. NML Technical Journal, 12 (1). pp. 22-28.

Singh, Inder (1993) Inhibition of steel corrosion by thiourea derivatives. Corrosion, 49 (6). pp. 473-478.

Singh, Inder and Banerjee, M K and Nag, P S (1981) Internal hydrogen embrittlement of cold drawn steels. Transactions of The Indian Institute of Metals, 34 (6). pp. 433-439.

Singh, Inder and Banerjee, T (1972) Effect of 2-mercaptobenzothiazole on aciddissolution and hydrogen absorption of steel. Corrosion Science, 12 (6). pp. 503-515.

Singh, Inder and Basu, D K and Singh, M N and Bhattamishra, A K and Dev, S C (1997) Role of silicon in the corrosion resistance of Cu-Si alloys in natural seawater. Anti-corrosion methods and materials, 44 (3). 195- .

Singh, Inder and Bhattamishra, A K (1998) Corrosion behaviour of magnesium alloys in chloride medium. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, Inder and Bhattamishra, A K and Basu, D K (1997) Electrochemical behaviour of AISI-316 stainless steels in sulphuric nitric acid mixtures. Anti-corrosion methods and materials, 44(3) . pp. 200-203.

Singh, Inder and Mukherjee, A N (1998) Corrosion of tinned sheets during transportation - A case study. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, Inder and Singh, Manjit (1987) Effect of metallic cations on the corrosion and the hydrogen absorption by cold-rolled mild-steel in inhibited sulfuric-acid. Corrosion science, 43 (7). pp. 425-429.

Singh, K and Patnaik, P and Bhaisare, D K and Jagannath, O and Krishnamurthy, N and Suri, A K (2011) Measurement of relative sticking coefficient of nitrogen on Al/Ti in a magnetron sputtering system. Journal of Metallurgy and Materials Science,, 53 (3). pp. 261-268.

Singh, K A and Pathak, L C and Roy, S K (2007) Effect of citric acid on the synthesis of nano-crystalline yttria stabilized zirconia powders by nitrate–citrate process. Ceramics International, 33 (8). pp. 1463-1468.

Singh, K K and Mondal, N and Choudhary, R B and Mishra, A K and Prasad, R R and Avtar, Ram and Mukerjee, D and Bhattacharya, G and Biswasroy, J K and Singh, Wakil (2011) Detection of Defects on Cold Rolling Mill (CRM) Rolls with Ultrasonic and Eddy Current Flaw Dectors. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries -NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Singh, Kulwant and Bidaye, A C and Suri, A K (2010) Model for prediction of coating composition deposited by sputtering using composite target in a reactive gas environment. Journal of Metallurgy and Materials Science, 52 (4). pp. 317-329.

Singh, M N and Mukherjee, K P and Guha, B K and Altekar, V A (1978) Evaluation of corrosion-resistance properties of nickel-free stainless-steels developed in National-Metallurgical-Laboratory. Transactions of the Indian Institute of Metals, 31 (1). pp. 61-64.

Singh, M N and Singh, Inder (1998) High temperature resistant slurry based coating for steel. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, M N and Singh, T B and Bhattamishra, A K and Basu, D K and Narang, S K (2003) Utilization of zinc dross as anode during electro-deposition of zinc-iron alloy coatings on steel substrate using chloride bath. Journal of Metallurgy and materials Science, 45 (2). pp. 91-95.

Singh, M P (1994) Super-Plastic forming of Metals. In: Tailoring of properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Singh, M P and Arora, K S and Kumar, Rajneesh and Shukla, D K and Prasad, S S (2020) Influence of heat input on microstructure and fracture toughness property in different zones of X80 pipeline steel weldments. Fatigue & Fracture of Engineering Materials & Structures, 44(1) (IF-3.031). pp. 85-100.

Singh, Manjit and Kumar, Rajendra (1973) Structure of liquid aluminum-silicon alloys. Journal of Materials Science, 8 (3). pp. 317-323.

Singh, Narinder and Mathur, S B (1976) Studies on extraction of selenium and tellurium from copper electrolytic slimes by sublimation in vacuum. Phosphorus sulfur and silicon and the related elements, 1 (2-3). pp. 169-176.

Singh, Narinder and Mathur, S B and Akerkar, D D (1973) Refining of selenium-A review. NML Technical Journal, 15 (1). pp. 17-23.

Singh, Narinder and Mathur, S B and Altekar, V A (1982) Development of a metallothermic process of smelting of lead concentrate. Transactions of the Indian Institute of metals, 35 (1). 51-&.

Singh, Narinder and Stroncz, W (1973) Selenium in xerography. Journal of Scientific & Industrial Research, 32 (12). pp. 740-746.

Singh, Nidhi and Singh, Vakil (2008) Effect of temperature on tensile properties of near-alpha alloy Timetal 834. Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing, 485 (1-2). pp. 130-139.

Singh, P K and Bhasin, V and Vaze, K K and Ghosh, A K and Kushwaha, H S and Murthy, D S R (2008) Fatigue studies on carbon steel piping materials and components: Indian PHWRs. Nuclear Engineering and Design, 238 (4). pp. 801-813.

Singh, P K and Ranganath, V R and Tarafder, S and Prasad , P and Bhasin, V and Vaze, K K and Kushwaha, H S (2003) Effect of cyclic loading on elastic-plastic fracture resistance of PHT system piping material of PHWR. International Journal of Pressure Vessels and Piping, 80 (10). pp. 745-752.

Singh, R J (2002) Utilisation of Waste- A Novel Approach Towards Cleaner Environment. In: Proceedings of Resurgence of Metallic Materials the Current Scenario-ROMM 2002, Oct. 24 & 25, 2002, National Metallurgical Laboratory(CSIR), Jamshedpur.

Singh, R J and Surbhi, (2013) Lowering of alumina in high alumina iron ores to produce DR grade iron ore pellets. Journal of Metallurgy and Materials Science, 55(1) . pp. 37-48.

Singh, R K and Misra, S (2013) Corrosion protection of stainless steel in CO2 environment by nanocoating of zinc phosphate with DLC filler. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 149-156.

Singh, R N and Madhu, and Awasthi, R and Tiwari, S K (2009) Iron molybdates as electrocatalysts for O2 evolution reaction in alkaline solutions. International Journal of Hydrogen Energy, 34 (11). pp. 4693-4700.

Singh, R N and Sharma, T and Singh, A and Anindita, and Mishra, D and Tiwari, S K (2008) Perovskite-type La2−xSrxNiO4 (0 ≤ x ≤ 1) as active anode materials for methanol oxidation in alkaline solutions. Electrochimica Acta, 53 (5). pp. 2322-2330.

Singh, R N and Singh, A and Mishra, D and Tiwari, S K and Gunjan, M K (2008) Influence of substitution of Ru on the electrocatalytic properties of the perovskite-type LaSrNiO4 electrode towards methanol oxidation. Indian Journal Of Chemistry Section A-Inorganic Bio-Inorganic Physical Theoretical & Analytical Chemistry , 47 (8). pp. 1187-1193.

Singh, Raghubir (1994) Heat Treatment of Creep Resistant Steels. In: Workshop on Heat Treatment & Surface Engineering of Iron & Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Singh, Raghubir (2001) Remaining Life Assessment of Engineering Components after Prolonged Creep Exposure: Some Issues and Case Histories. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. NML, Jamshedpur, India, Jamshedpur, pp. 70-84. ISBN 81-87053-62-3

Singh, Raghubir (1995) Remaining life assessment of high-temperature components using threshold stress concept. Sadhana-academy proceedings in engineering sciences, 20 ( ). pp. 87-101.

Singh, Raghubir and Banerjee, S (1991) Morphological and compositional changes of the carbides in Cr-Mo-V ferritic steel. Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing , 132 ( ). pp. 203-211.

Singh, Raghubir and Banerjee, S (1992) Resisting stress of a low-alloy ferritic steel after creep exposure in service. Acta metallurgica et materialia, 40 (10). pp. 2607-2616.

Singh, Raghubir and Choubey, R and Kumar, R (1976) Rationalization of the blading material for steam turbines: Their requirements and selection. NML Technical Journal, 18 (4). pp. 69-72.

Singh, Raghubir and Kumar, Rajendra (1984) On some aspects of creep deformation of low-alloy Cr-Mo-V creep resistant steels. Transactions of the Indian Institute of metals, 37 (5). p. 451.

Singh, Raghubir and Singh, S R (1997) Remaining creep life study of Cr---Mo---V main steam pipe lines. International Journal of Pressure Vessels and Piping, 73 (1). pp. 89-95.

Singh, Raghubir and Singh, S R (1997) Remaining creep life study of Cr-Mo-V main steam pipe lines. International Journal of Pressure Vessels and Piping, 73 (1). pp. 89-95.

Singh, Raghuvir (2008) Influence of cold rolling on sensitization and intergranular stress corrosion cracking of AISI 304 aged at 500 °C. Journal of Materials Processing Technology, 206 (1-3). pp. 286-293.

Singh, Raghuvir and Dahotre, N B (2007) Corrosion degradation and prevention by surface modification of biometallic materials. Journal of Materials Science-Materials in Medicine, 18 (5). pp. 725-751.

Singh, Raghuvir and Das, Goutam and Singh, P K and Chattoraj, I (2009) Low-Temperature Sensitization Behavior of Base, Heat-Affected Zone, and Weld Pool in AISI 304LN. Metallurgical and Materials Transactions A, 40 (5). pp. 1219-1234.

Singh, Raghuvir and Ghosh Chowdhury, S and Das, Goutam and Singh, P K and Chattoraj, I (2012) Low Temperature Sensitization on the Orthogonal Surfaces of Prior deferomed AISI 304LN and aged at 673K to 873K (400 A degress C to 600 A degress C. Metallurgical and Materials Transaction A, 43A (3). pp. 986-1003.

Singh, Raghuvir and Ghosh Chowdhury, S and Das, Goutam and Singh, P K and Chattoraj, I (2012) Study on sensitization susceptibility and texture of cold rolled AISI 304LN stainless steel. Materials Science Forum, 702-703 . pp. 677-680.

Singh, Raghuvir and Kumar, Damodar and Mishra, Suman K and Tiwari, S K (2014) Laser cladding of Stellite 6 on stainless steel to enhance solid particle erosion and cavitation resistance. Surface and Coatings Technology, 251 (IF-2.199). pp. 87-97.

Singh, Raghuvir and Kumar, Mukesh and Ghosh, M and Das, Goutam and Singh, P K and Chattoraj, I (2013) Intergranular Corrosion Behavior of 304LN Stainless Steel Heat Treated at 623 K (350 degrees C). Metallurgical and Materials Transactions A-Physical Metallurgy and Materials and Materials Science, 44A (IF-1.627). pp. 173-187.

Singh, Raghuvir and Martin, M and Dahotre, N B (2005) Influence of laser surface modification on corrosion behavior of stainless steel 316L and Ti-6Al-4V in simulated biofluid. Surface Engineering, 21 (4). pp. 297-306.

Singh, Raghuvir and Singh, A K (2002) In-plant corrosion test on special stainless steels in bleach plant of paper industry. Indian Journal of Chemical Technology, 9 (2). pp. 141-147.

Singh, Rahul and Yadav, Surya Deo and Sahoo, Biraj K and Ghosh Chowdhury, S and Kumar , Abhishek (2021) Phase transformation, Mechanical Properties and Corrosion Behavior of 304L Austenitic Stainless Steel Rolled at Room and Cryo Temperatures. Defence Science Journal, 71(3) . pp. 383-389.

Singh, Raj Kumar and Kumari, Mamta and Prasad, J N (2011) A first principle numerical approach to spin dependent transport. Journal of Metallurgy and Materials Science, 53 (3). pp. 275-287.

Singh, Raj Kumar and Kumari, Mamta and Prasad, J N (2011) Interaction of ferromagnet conduction electron spin with spatial and time varying magnetization. Journal of Metallurgy and Materials Science, 53 (2). pp. 153-159.

Singh, Rajesh Kumar (2015) Corrosion and corrosion protection of mild steel in SO environment. Journal of Metallurgy and Materials Science, 57(1) . pp. 33-40.

Singh, Rajesh Kumar (2014) Corrosion protection of mild steel by organic inhibitors. Journal of Metallurgy and Materials Science, 56(3) (NON-SCI). pp. 187-193.

Singh, Rajesh Kumar (2010) The corrosion protection of stainless steel in phosphate fertilizer industry. Journal of Metallurgy and Materials Science, 52 (2). pp. 173-180.

Singh, Rajesh Kumar (2014) Corrosion protection of stainless steel in 15% H SO 2 4. Journal of Metallurgy and Materials Science, 56(4) (NON-SCI). pp. 239-244.

Singh, Rajesh Kumar and Misra, S (2013) Corrosion protection of rebar steel in marine atmosphere by nanocoating. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 313-321.

Singh, Rajesh Kumar and Misra, S (2013) Corrosion protection of mild steel in SO2 environment by nanocoating with filler. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 227-234.

Singh, Ranjeet K and Dey, Shobhana and Mohanta, M K and Das, Avimanyu (2014) Enhancing the Utilization Potential of a Low Grade Chromite Ore through Extensive Physical Separation. Separation Science and Technology, 49(12) (IF-1.200). pp. 1937-1945.

Singh, Ratnakar and Banerjee, S (1992) Resisting stress of a low-alloy ferritic steel after creep exposure in service. Acta Metallurgica Et Materialia, 40 (10). pp. 2607-2616.

Singh, Ratnakar and Ravi Kumar, B and Kumar, A and Dey, P K and Chattoraj, I (2003) The effects of cold working on sensitization and intergranular corrosion behavior of AlSl 304 stainless steel. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science , 34-A (11). pp. 2441-2447.

Singh, Ratnakar and Subba Rao, S and Maulik, S C and Chakravorty, N (1997) Fine particles flotation - Recent trends. Transactions of the Indian Institute of Metals, 50 (5). pp. 407-419.

Singh, Ravinder Pal and Singh, Harvinder (2011) Characterization and comparison of treated and untreated rich hush ash & fly ash for metal matrix composites. Journal of Metallurgy and Materials Science, 53 (2). pp. 189-196.

Singh, S and Roy, Rajat K and Ghosh, M and Mitra , A and Panda, A K (2012) Heat Treatment Induced Martensitic Accommodation and Adaptive Anisotropy in Melt Spun Ni55Mn22Ga23 (at.%) ribbons. Journal of Applied Physics, 112(10) .

Singh, S K and Verma, B K and Pandey, L P (1989) Studies on the chelation behavior of phenanthrenequinone monosemicarbazone with rare-earth elements. Bulletin De La Societe Chimique De France (1). pp. 26-30.

Singh, S R (2001) Catastrophic carburisation in petrochemical industry. In: Recent trends in structural integrity assessment: proceedings of workshop, Jan 18-19, 2001. NML, Jamshedpur, pp. 46-57. ISBN 81-87053-62-3

Singh, S R (2001) Catastrophic Carburisation in Petrochemical Industry. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. National Metallurgical Laboratory, Jamshedpur, Jamshedpur, pp. 46-57. ISBN 81-87053-62-3

Singh, S R (2007) Material Equivalence of Russain Materials for Invar Missile. Consultancy (CNP). CSIR-NML, Jamshedpur. (Submitted)

Singh, S R and Das, S K and Gunjan, M K (2007) Flying Accident to Mig-21/C-1129 of MOFTU 'A'/11 Wg/Eac. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Singh, S R and Das, Swapan K (2007) Failure Analysis of Cables of Undercarriage Door Control Mechanism : AN-32 Aircraft. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Singh, S R and Ghosh, M and Das, Swapan K (2006) Metallurgical Analysis of Copper Driving Band of GSH 30 MM HEI (INERT) Aircraft Ammunition of Russian Origin. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Singh, S R and Gunjan, M K and Kumar, Arvind (2006) Failure Analysis of Bolts of Wheel Hub Assembly of AN-32 Aircraft and Comparative Metallurgical Analysis of Russian and Indigenised Bolts. Other (TMP). CSIR-NML, Jamshedpur. (Submitted)

Singh, S R (1995) Principles of Optical and Electron Microscopy. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Singh, Sanjay and Bhardwaj, S and Panda, A K and Ahire, V and Mitra, A and Awasthi, A M and Barman, S R (2010) Structural, Thermal and Magnetic Properties of Ga Excess Ni-Mn-Ga. Materials Science Forum, 635 . pp. 43-47.

Singh, Satnam and Roy, P K and Ghosh, M and Mitra, A and Panda, A K (2013) Martensitic transformation and magneto-strain in melt spun NiMnGaAl Ferromagnetic Shape Memory Alloys. Intermetallics, 43 (IF-1.857). pp. 147-151.

Singh, Satnam and Roy, R K and Mahato, B and Ghosh, M and Mitra, A and Panda , A K (2014) Effect of Al incorporation for Co on the gamma-beta phase boundary of rapidly solidified CoNiAl ferromagnetic shape memory alloys. Journal of Magnetism and Magnetic Materials, 368 (IF-2.002). pp. 379-383.

Singh, Satnam and Roy, Rajat K and Ghosh, M and Manik, N B and Mitra, A and Panda, A K (2013) Modification in martensite morphology and magneto-strain through rapid solidification and heat treatment of NiMnGaAl alloy. Journal of Magnetism and Magnetic Materials, 343 (IF-1.826). pp. 169-172.

Singh, Swarnima and Pandey, K K and Bose, S K and Keshri , A K (2020) Role of surface nanocrystallization on corrosion properties of low carbon steel during surface mechanical attrition treatment. Surface and Coatings Technology, 396 (IF-3.192). p. 125964.

Singh, Swarnima and Tiwari, S K and Singh, Raghuvir (2020) Influence of laser scanning speed on nitrided Ti6Al4V surface. Surface Engineering, 36(12): Special Issue: Laser . pp. 1285-1293.

Singh, T B and Dey, A K and Gaur, B and Singh, D D N (1995) Are corrosion, hydrogen absorption and mechanical strength of steel exposed to inhibited acid solution interrelated? Anti-corrosion Methods & Materials, 42 (6). pp. 19-22.

Singh, T B and Lal, Kishori and Mohanty, R K (1998) Corrosion behaviour of rapidly solidified lead-aluminium alloys for battery grids. In: International Conference on Corrosion (CORCON 97), Dec 03-06, 1997, Nehru Ctr, Mumbai, India.

Singh, U P and Banerjee, S (1991) On the origin of pop-in crack extension. Acta metallurgica et materialia, 39 (6). pp. 1073-1083.

Singh, V and Biswas, N and Chakravarty, T and Rao, S Mohan and Banerjee, P K (2013) Exploitation of lean grade manganese ores from Joda Mines. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 59-65.

Singh, Vikas and Das, Suchandan K (2018) Mathematical Model and Plant Investigation to Characterize Effect of Casting Speed on Thermal and Solidification Behavior of an Industrial Slab Caster. ISIJ International, 423 . pp. 1-10.

Singh, Virendar and Adhikary, M and Venugopalan, T and Chakraborty, A and Nanda, T and Kumar, B Ravi (2017) Role of recrystallization and pearlite dissolution in industrial processing of DP590 steels. Materials and Manufacturing Processes, 32(16) (IF-2.274). pp. 1806-1816.

Singhal, Umesh (1994) Roll Qualities and Economic Utilisation of Rolls. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Singhbabu, Y N and Choudhary, Shyam K and Shukla, N and Das, S and Sahu, Ranjan K (2015) Observation of large positive magneto-resistance in bubble decorated graphene oxide films derived from shellac biopolymer: a new carbon source and facile method for morphology-controlled properties†. Nanoscale, 7 (IF-6.739). pp. 6510-6519.

Singhbabu, Y N and Kumari, Priya and Parida, Sunena and Sahu, Ranjan K (2014) Conversion of pyrazoline to pyrazole in hydrazine treated N-substituted reduced graphene oxide films obtained by ion bombardment and their electrical properties. Carbon, 74 (IF-6.160). pp. 32-43.

Singhbabu, Y N and Sahu, K K and Dadhich, D and Pramanick, A K and Mishra, T and Sahu, Ranjan K (2013) Capsule-embedded reduced graphene oxide: synthesis, mechanism and electrical properties. Journal of Materials Chemistry, 1 (IF-5.97). pp. 958-966.

Singhbabu, Y N and Sivakumar, B and Singh, J K and Bapari, H and Pramanick, A K and Sahu, Ranjan K (2015) Efficient anti-corrosive coating of cold-rolled steel in a seawater environment using an oil-based graphene oxide ink†. Nanoscale, 7 (6.739). pp. 8035-8047.

Sinha, A N (1995) Image Analysis & Quantitative Metallography. In: Experimental Techniques in Industrial Metallography [ETIM - 95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory (CSIR), Jamshedpur.

Sinha, A N (1984) Lattice-parameters of iron-aluminum alloys. Transactions of the Japan Institute of Metals, 25 (12). pp. 900-901.

Sinha, A N (1995) Specimen Preparation for Optical Microscopy. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Sinha, A N and Das, N K and Bose, S K (1983) SEM-A tool for metallurgical analysis. NML Technical Journal, 25 (1-2). pp. 1-10.

Sinha, A N and Halder, B N and Mohanty, O N (1991) Failure of a locomotive axle - a metallographic investigation - a premature failure of a locomotive axle is attributed to improper welding. Welding Journal, 70 (4). pp. 59-61.

Sinha, A N and Sivaramakrishnan, C S (1994) Failure of work roll of cold-rolling mill. Ironmaking & Steelmaking, 21 (2). pp. 154-157.

Sinha, Arvind and Agrawal, A and Das, S K and Ravi Kumar, B and Rao, Venkatesh and Ramachandrarao, P (2001) On the growth of monoclinic calcium carbonate in poly(vinyl alcohol). Journal of Materials Science Letters, 20 (17). pp. 1569-1572.

Sinha, Arvind and Agrawal, A and Nayar, S and Das, S K and Ramachandrarao, P (2002) Morphosynthesis of Calcium Carbonate in Poly(vinylalcohol). Morphosynthesis of Calcium Carbonate in Poly(vinylalcohol) , 10 (3). pp. 149-153.

Sinha, Arvind and Chakraborty, J and Das, Swapan K and Ramachandrarao, P (2003) Self-assembled growth of calcite particles on a tobacco film. Current Science , 84 (11). pp. 1437-1440.

Sinha, Arvind and Chakraborty, J and Das, Swapan K and Rao, Venkatesh and Ramachandrarao, P (2001) Oriented arrays of nanocrystalline magnetite in polymer matrix produced by biomimetic synthesis. Materials Transactions, 42 (8). pp. 1672-1675.

Sinha, Arvind and Chakraborty, J and Joy, P A and Ramachandrarao, P (2004) Magnetic field-induced biomimetic synthesis of superparamagnetic poly (vinyl alcohol)-maghemite composite. Journal of Materials Research, 19 (6). pp. 1676-1681.

US2002000112044 (2004) Process for the preparation of nanosized iron oxide by biomimetic route. US6800271.

Sinha, Arvind and Das, Swapan K and Rao, Venkatesh and Ramachandrarao, P (2001) Biomimetic route to produce nanosized inorganic crystals. Scripta Materialia, 44 (8-9). pp. 1933-1936.

Sinha, Arvind and Das, Swapan K and Rao, Venkatesh and Ramachandrarao, P (2001) Patterning of copper particles on polymeric surface. Journal of Materials Research, 16 (5). pp. 1354-1357.

Sinha, Arvind and Das, Swapan K and Ravi Kumar, B and Chakraborty, S and Rao, Venkatesh and Ramachandrarao, P (2000) Polymer-Mediated Synthesis of Fine-Sized Cobalt Particles. Journal of Materials Synthesis and Processing, 8 (2). pp. 109-113.

Sinha, Arvind and Das, Swapan K and Vijaya Kumar, T V and Rao, Venkatesh and Ramachandrarao, P (1999) Synthesis of Nanosized Copper Powder by an Aqueous Route. Journal of Materials Synthesis and Processing, 7 (6). pp. 373-377.

Sinha, Arvind and Guha, Avijit (2009) Biomimetic patterning of polymer hydrogels with hydroxyapatite nanoparticles. Materials Science and Engineering: C, 29 (4). pp. 1330-1333.

Sinha, Arvind and Gupta, A K and Pramanick, A K and Nayar, S and Gunjan, M K and Mishra, T and Bhatt, N C and Vishwanath, N and Das, Samar (2009) Mimicking biomineralization under microgravity. Materials Science and Engineering: C, 29 (3). pp. 779-784.

Sinha, Arvind and Kannde, D (2006) Self-assembly-assisted growth of two-dimensional Penrose tiling. Philosophical Magazine Letters Online ISSN 1362-3036, 86 (2). pp. 75-80.

Sinha, Arvind and Mishra, T and Ravishankar, N (2008) Polymer assisted hydroxyapatite microspheres suitable for biomedical application. Journal of Materials Science: Materials in Medicine, 19 (5). pp. 2009-2013.

Sinha, Arvind and Nayar, S (2005) Design and synthesis of nanosized bioceramic-particles, composites and coating. Transactions Of The Indian Institute Of Metals , 58 (6). pp. 951-955.

Sinha, Arvind and Nayar, S and Agrawal, A and Bhattacharya, D (2003) Synthesis of nanosized and microporous precipitated hydroxyapatite in synthetic polymers and Biopolymers. Journal Of The American Ceramic Society , 86 (2). pp. 357-359.

Sinha, Arvind and Nayar, S and Murthy, G V S and Joy, P A and Rao, Venkatesh and Ramachandrarao, P (2003) Biomimetic synthesis of superparamagnetic iron oxide particles in proteins. Journal of Materials Research, 18 (6). pp. 1309-1313.

Sinha, Arvind and Nayar, S and Nath, B K and Das, D and Mukhopadhyay, P K (2005) Magnetic field induced synthesis and self-assembly of super paramagnetic particles in a protein matrix. Colloids and Surfaces B: Biointerfaces, 43 (1). pp. 7-11.

Sinha, Arvind and Ramachandrarao, P (1995) On the grey penrose tiling. Philosophical Magazine Letters, 71 (3). pp. 207-212.

Sinha, Arvind and Ramachandrarao, P (1997) Quasiperiodic lattices. Progress in Crystal Growth and Characterization of Materials, 34 (1-4). pp. 147-156.

Sinha, Arvind and Ramachandrarao, P and Sastry, G V S (1995) Selection-rules for quasi-lattices. Current Science, 68 (6). pp. 627-631.

Sinha, D and Sahoo, K L and Sinha, U B and Swu, T and Chemseddine, A and Fink, D (2004) Gamma-induced modifications of polycarbonate polymer. Radiation Effects and Defects in Solids, 159 (10). pp. 587-595.

Sinha, I and De, P K and Srivastava, V C (2005) Mechanical working of 2124 Al alloy—SiCp cast composites. Journal of Materials Science, 40 (22). pp. 6045-6048.

Sinha, I and Mandal, R K (2002) Simulating isothermal crystallisation during phase separation of oxide glasses and the percolation behaviour of these glass-ceramics. Journal of Materials Science, 37 (24). pp. 5215-5221.

Sinha, I and Mandal, R K (2003) Simulating the effect of glass microstructures on the crystallisation and percolation behaviour of glass-ceramics. Journal of Non-Crystalline Solids, 324 (1-2). pp. 36-49.

Sinha, Moni and Nistala, Harsha (2015) Microstructural analysis of sinter breakage. Journal of Metallurgy and Materials Science, 57(2) . pp. 75-82.

Sinha, Moni and Nistala, Harsha and Biswas, A (2015) Effect of inert gas injection on sinter RDI. Journal of Metallurgy and Materials Science, 57(3) . pp. 173-178.

Sinha, N and Singh, R (2014) Beneficiation and purification of a low grade and finely disseminated graphite ore. Journal of Metallurgy and Materials Science, 56(1) (NON-SCI). pp. 15-22.

Sinha, P K (1998) Modern Composites - A Renascent Material System. In: Proceedings of Composite Materials. NML, Jamshedpur, India, Jamshedpur, pp. 1-8.

Sinha, P K and Basu, G and Aush, S C and Dhananjayan, N and Altekar, V A (1980) Recovery of non-ferrous-metals and elemental sulfur by ferric-chloride leaching of sulfide concentrates. Transactions of the Indian Institute of Metals, 33 (6). pp. 431-438.

Sinha, S K and Godiwalla, K M and Sivaramakrishnan, C S (1993) Fluid-flow characterization in twin strand continuous-casting tundish water model. Ironmaking & Steelmaking, 20 (6). pp. 485-492.

Sinha, S K and Rao, G N (1976) Cellular metal. NML Technical Journal, 18 (2). pp. 21-24.

Sinha, Satish and Guha, Avijit and Sinha, Arvind (2010) Macroporous hybrid frameworks for bone graft substitute. Materials Science and Engineering: C, 30 . pp. 873-877.

Sinha, THD and Prasad, R S and Kumar, Rajendra (1975) Thermoelectric-power and resistivity of Cu-In alloys at high-temperatures. Indian Journal of Pure & Applied Physics, 13 (7). pp. 443-446.

Sircar, J K and Bhattacharjee, S and Konar, J and Ghosh, K C and Basak, A C and Jha, S N and Pandey, L P (1996) Determination of Low Amount of Chromium in Alloy Steel by an Amplification Method. Microchemical Journal, 54 (2). pp. 163-167.

Sircar, J K and Rao, A S and Upadhyay, A K and Kumar, B and Srivastava, S C (2002) Principle of meta-stable defocusing in mass spectrometry. Journal of Metallurgy and materials Science., 44 (3). pp. 151-159.

Sircar, J K and Upadhyay, A K and Gupta, K K (2006) Determination of phosphorus in steel by precipitation as silverphosphate and subsequent determination by spectrophotometric method. Journal of Metallurgy and Materials Science, 47 (1). pp. 45-50.

Siruguri, V and Gutiérrez, J and Barandiaràn, J M and Làzpita, P and Singh, Brajendra and Sahu, Ranjan K and Sundar Manoharan, S and Henry, P and Mondelli, C (2006) Neutron diffraction evidence for double exchange coupling in Ru-substituted La0.6Pb0.4Mn1−xRuxO3, 0x0.5. Physica B: Condensed Matter, 385-386 (1). pp. 408-410.

Sivaiah, S and Rafiuddin, S and Chakravorty, N (1984) Flow properties of granular solids. NML Technical Journal, 26 (1-2). pp. 11-14.

Sivakumar, B and Singh, Raghuvir and Pathak, L C (2015) Corrosion behavior of titanium boride composite coating fabricated on commercially pure titanium in Ringer's solution for bioimplant applications. Materials Science & Engineering C-Materials for Biological Applications, 48 (IF-2.736). pp. 243-255.

Sivaprasad, S and Bar, H N and Gupta, Suneel K and Arora, Punit and Bhasin, V and Tarafder, S (2014) A comparative assessment of cyclic deformation behaviour in SA333 Gr.6 steel using solid, hollow specimens under axial and shear strain paths. International Journal of Fatigue, 61 (IF- 1.916). pp. 76-86.

Sivaprasad, S and Ghosh, M and Das, Swapan K and Ghosh Chowdhury, S and Tarafder, S (2007) Evolution of Deformation-Induced Martensite during Fatigue Deformation of AISI 304LN Stainless Steel. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Sivaprasad, S and Paul, Surajit Kumar and Gupta, Suneel K and Bhasin, V and Narasaiah, N and Tarafder, S (2010) Influence of uniaxial ratchetting on low cycle fatigue behaviour of SA 333 Gr.6 C–Mn steel. International Journal of Pressure Vessels and Piping, 87 (8). pp. 464-469.

Sivaprasad, S and Paul, Surajit Kumar and Gupta, Suneel K and Bhasin, Vivek and Narasaiah, N and Tarafder, S (2010) Influence of uniaxial ratchetting on low cycle fatigue behviour of SA 333 Gr. 6 C–Mn steel. International Journal of Pressure Vessels and Piping, 87(8) . pp. 464-469.

Sivaprasad, S and Swaminathan, J and Tiwari, Y N and Roy, P K and Singh, Raghubir (2003) Remaining life assessment of service exposed reactor and distillation column materials of a petrochemical plant. Engineering Failure Analysis, 10 (3). pp. 275-289.

Sivaprasad, S and Tarafder, S and Das, Swapan K and Ranganath, V R and Ray, K K (2001) The role of stereology in estimation of ductile fracture toughness of structural materials. Image Analysis in Materials and Life Sciences . pp. 86-95.

Sivaprasad, S and Tarafder, S and Ranganath, V R and Das, Swapan K and Ray, K K (2002) Effect of prestrain on stretch-zone formation during ductile fracture of Cu-strengthened high-strength low-alloy steels. Metallurgical and Materials Transactions A, 33 (12). pp. 3731-3740.

Sivaprasad, S and Tarafder, S and Ranganath, V R and Ray, K K (2004) Modelling ductile fracture behaviour from deformation parameters in HSLA steels. Fatigue & Fracture of Engineering Materials & Structures, 27 (10). pp. 897-909.

Sivaramakrishnan, C S and Lal, Kishori and Mahanti, R K (1991) Characterization of rapidly solidified structures of Al-6Fe-3mm. Journal of Materials Science, 26 (16). pp. 4369-4374.

Sivaramakrishnan, C S (1973) Bearing materials-A general appraisal. NML Technical Journal, 159 (3). pp. 69-75.

Sivaramakrishnan, C S (1995) Physical Metallurgy of Aluminium. In: Experimental Techniques in Industrial Metallography [ETIM-95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Sivaramakrishnan, C S (2001) Solidification Processing of aluminium alloys. Journal of Metallurgy and materials Science, 43 (2). pp. 57-66.

Sivaramakrishnan, C S (1978) Stability of liquid lead base alloys: Some simple consideration. NML Technical Journal, 20 (3-4). pp. 31-34.

Sivaramakrishnan, C S (1978) Thermodynamic properties of liquid lead tin system by EMF method. NML Technical Journal, 20 (1-2). pp. 20-23.

Sivaramakrishnan, C S and Kumar, Rajendra (1976) Structure of dilute Sn-Fe liquid alloys. Transactions of the Japan Institute of Metals, 17 (6). pp. 378-382.

Sivaramakrishnan, C S and Mahanti, R K and Kumar, R (1984) The dispersion of lead and graphite in aluminium alloys for bearing applications. Wear, 96 (2). pp. 121-134.

Sivaramakrishnan, C S and Mahanti, R K and Kumar, Rajendra (1982) Grain-refinement of aluminum by nml-pm122. Indian Journal of Technology, 20 (10). pp. 403-406.

Sivaramakrishnan, C S and Mahanti, R K and Kumar, Rajendra (1986) Microstructural refinement in degassed aluminum-alloys. Transactions of the Indian Institute of metals, 39 (5). pp. 492-496.

Som, P K and Choudhury, S K R (1982) Studies on lime-roast-leach technique for treating chalcopyrite concentrates. Transactions of The Indian Institute Of Metals, 35 (6). pp. 578-582.

Som, P K and Roychowdhury, S K and Aush, S C (1977) Chlorination of magnesites. Transactions of the Indian Institute of metals, 30 (2). pp. 95-105.

Soni, and Sharma, S K and Mishra, Suman K (2020) The effect of Si content on structural, mechanical and optical behaviour of magnetron sputtered Al–Si–N nanocomposite thin films. Journal of Alloys and Compounds, 831 (IF-4.175). p. 154686.

Soupramanien, C and Paul, K K and Sivaprasad, S and Tarafder, S and Narasaiah, N (2011) Design and Development of Loading Fixture for Mixed Mode I/II Fracture Studies. Exploratory (OLP). CSIR-NML, Jamshdpur. (Submitted)

Soupramanien, C and Swaminathan, J (2014) Failure analysis of refractory anchors of powder boiler. Procedia Engineering, 86 (NIF-0.629). pp. 919-925.

Sridhar, G (1995) Physical Metallurgy of Some Important Non-ferrous Metals and Alloys. In: Experimental Techniques in Industrial Metallography [ETIM - 95], Nov.27 to Dec. 1, 1995, National Metallurgical Laboratory(CSIR), Jamshedpur.

Sridhar, G and Ghosh Chowdhury, S and Singh, S R and Parida , N and Singh, D D N and Das, Swapan K and Roy, P K and Das , Goutam and Gunjan, M K (2006) Failure Analysis of LP Turbine Blade of NTPC-Tanda. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Sridhar, G and Iyer, V Rama and Rao, V Rama Krishna (2000) Electro Slag cladding of Dissimilar steels and study of the bond interface (OLP-12731). Exploratory (OLP). National Metallurgy Laboratory, Jamshedpur, Jamshedpur. (Submitted)

Sridhar, G and Sarma, D S (1989) Structure and properties of a beta-solution treated, quenched, and aged Si-bearing near-alpha titanium-alloy. Metallurgical Transactions A-Physical Metallurgy and Materials Science, 20 (1). pp. 55-62.

Sridhar, G and Sarma, D S (1988) Structure and properties of a near-alpha titanium-alloy after beta-solution treatment and aging at 625-degrees-c. Metallurgical transactions a-physical metallurgy and materials science, 19(12) . pp. 3025-3033.

Sridhar, G and Singh, S R (2007) Opinion on the Cause of Damage of Last Stage Blade of 37 MW Steam Turbine of Monnet Ispat and Energy Ltd., Raigarh, Chattisgarh. Consultancy (CNP). CSIR-NML, Jamshedpur. (Submitted)

Sridhar, G and Singh, S R and Das, Swapan K (2006) Assessment of Microstructural Degeneration in Base Metal and Coating of Service Exposed IN 738 LC Gas Turbine Blade. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Sridhar, G and Singh, S R and Das, Swapan K and Gunjan, M K (2006) Failure Analysis of Engine Block of 6.2 MW DG set of Hindustan Glass Ltd. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Sridhar, G and Singh, S R and Das, Swapan K and Gunjan, M K and Rupa, P K P (2007) Failure Analysis of Damaged parts of a Roller press at Jay Pee Bela Cement Plant, M.P. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Srikanth, S (1992) Calculation of viscosity from the associated solution model - discussion. Metallurgical Transactions B-Process Metallurgy , 23 (1). pp. 101-103.

Srikanth, S (2011) CSIR-National Metallurgical Laboratory, Jamshedpur, India. [Presentation Slide] (Submitted)

Srikanth, S (2010) CSIR-NML Diamond Jubilee Anniversary Celebrations. [Presentation Slide] (Unpublished)

Srikanth, S (2015) CSIR-NML Equipment Facility Handbook. CSIR-National Metallurgical Laboratory, Jamshedpur.

Srikanth, S (2015) CSIR-NML Technology Handbook. CSIR-National Metallurgical Laboratory, Jamshedpur.

Srikanth, S (2011) Current Activities at CSIR-NML on Steel. [Presentation Slide] (Submitted)

Srikanth, S (1991) Estimation of volumes of mixing and calculation of the liquidus curve from the modified associated solution model. Zeitschrift fur metallkunde, 82 (11). pp. 841-845.

Srikanth, S (2011) Evaluation of Structural Integrity. [Presentation Slide] (Submitted)

Srikanth, S (2011) Institutional Collaboration: India-Australia. [Presentation Slide] (Submitted)

Srikanth, S (2012) The Journey of CSIR-National Metallurgical Laboratory. [Presentation Slide] (Submitted)

Srikanth, S (2012) Materials Development Program at CSIR-NML, Jamshedpur. [Presentation Slide] (Unpublished)

Srikanth, S (2011) Processing of Secondaries & Waste. [Presentation Slide] (Unpublished)

Srikanth, S (2015) Some recent technological achievements of CSIR-National Metallurgical Laboratory. Current Science, 108(11) . pp. 2014-2016.

Srikanth, S and Alex, T C and Agrawal, A and Premchand, (1997) Reduction roasting of deep sea manganese nodules using liquid and gaseous reductants. In: 2nd ISOPE Ocean Mining Symposium, Nov 24-25, 1997, Seoul, South Korea.

Srikanth, S and Alex, T C and Premchand, (1999) Reduction roasting of central Indian Ocean nodules by use of fuel oil: a thermodynamic and kinetic analysis. Transactions of the Institution of mining and metallurgy section c-mineral processing and extractive metallurgy, 108 ( ). C138-C146.

Srikanth, S and Chakravorty, M (2001) Non-isothermal thermoanalytical studies on the salt roasting of chalcopyrite using KCl. Thermochimica Acta, 370 (1-2). pp. 141-148.

Srikanth, S and Chakravorty, M (2001) Thermoanalytical studies on the salt roasting of chalcopyrite using KCl. Analytical Chemistry (including News & Features), 370 (1-2). pp. 141-148.

Srikanth, S and Chattopadhyay, S (1992) Thermodynamic calculation of phase-equilibria in the Al-Ge-Zn system. Thermochimica Acta, 207 (29-44). pp. 29-44.

Srikanth, S and Chattopadhyay, S (1993) Volume effects and complexing in liquid K-Pb alloys. Canadian Metallurgical Quarterly , 32 (2). pp. 103-107.

Srikanth, S and Das, Swapan K and Ravi Kumar, B and Rao, D S and Nandakumar, K and Vijayan, P (2004) Nature of fireside deposits in a bagasse and groundnut shell fired 20 MW thermal boiler. Biomass and Bioenergy, 27 (4). pp. 375-384.

Srikanth, S and Jacob, K T (1989) Extention of Darken's Quadric Formalism to Dilute Multicomponent solutions. ISIJ International, 29 (2). pp. 171-174.

Srikanth, S and laxmi, V Devi and Kumar, Rakesh (2015) Unfolding the complexities of mechanical activation assisted alkali leaching of zircon (ZrSiO4). Hydrometallurgy, Available online 10 December 2015 . (In Press)

Srikanth, S and Ramachandrarao, P (1998) Construction and application of metastability field diagrams for non-equilibrium processing of alloys. International Journal of Non-equilibrium processing, 10 (3-4). pp. 219-239.

Srikanth, S and Ramachandrarao, P and Chvoj, Z (2000) Limits of constitutional undercooling and interfacial liquid compositions during steady-state directional solidification of binary alloys at various interface velocities. Journal of Crystal Growth, 208 (1-4). pp. 779-785.

Srikanth, S and Sanyal, D and Ramachandrarao, P (1996) A re-evaluation of the Al---Ge system. Calphad, 20 (3). pp. 321-332.

Srinivasan, A and Ajithkumar, K K and Swaminathan, J and Pillai, U T S and Pai, B C (2013) Creep Behavior of AZ91 Magnesium Alloy. Procedia Engineering, 55 . pp. 109-113.

Srinivasan, A and Pillai, U T S and Swaminathan, J and Das, Swapan K and Pal, B C (2006) Observations of microstructural refinement in Mg–Al–Si alloys containing strontium. Journal of Materials Science, 41 (18). pp. 6087-6089.

Srinivasan, A and Pillai, U T S and Swaminathan, J and Pai, B C (2006) Enhanced high temperature properties of low pressure cast AZ91 Mg alloy. International Journal of Cast Metals Research, The, 19 (5). pp. 265-268.

Srinivasan, A and Swaminathan, J and Gunjan, M K and Pillai, U T S and Pal, B C (2010) Effect of intermetallic phases on the creep behavior of AZ91 magnesium alloy. Materials Science and Engineering: A, 527 (6). pp. 1395-1403.

Srinivasan, N R (1957) Tantalum & Niobium Minerals of India. In: Non-Ferrous Metal Industry in India. NML, Jamshedpur, India, Jamshedpur, pp. 25-29.

Srinivasan, S R (1974) Seminar on bacterial leaching. Chemical & Engineering News, 33 (1). pp. 11-14.

Srivastava, A K and Patel, N K and Ravi Kumar, B and Sharma, A and Ahn, Byungmin (2020) Strength-Ductility Trade-Off in Dual-Phase Steel Tailored via Controlled Phase Transformation. Journal of Materials Engineering and Performance, 29 . pp. 2783-2791.

Srivastava, J P and Pathak, P N (2000) Pre-concentration: a necessary step for upgrading tungsten ore. International Journal of Mineral Processing, 60 (1). pp. 1-8.

Srivastava, R R and Mishra, A N and Singh, V K (2013) Co-precipitation study of nickel and cobalt from ammoniacal leach liquor of laterite ore. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 67-72.

Srivastava, S C and Das, A N and Pandey, L P and Ram, S (1995) X-ray fluorescence study of fine powders of wolframite ores with SiO2 and WO3 major phases. Journal of Materials Science, 30 (24). pp. 6303-6308.

Srivastava, S C and Ghosh, M K (1976) X-ray spectrometric analysis of low alloy steels. NML Technical Journal, 18 (3). pp. 34-38.

Srivastava, S C and Godiwalla, K M and Banerjee, M K (1997) Fuel ash corrosion of boiler and superheater tubes. Journal of Materials Science, 32 (4). pp. 835-849.

Srivastava, S C and Subhashini, B (1975) A note on the analysis of nickel in the nickel complex with the help of x-ray fluorescence. NML Technical Journal, 17 (2). pp. 21-22.

Srivastava, V C and De, P K and Lakra, B A and Ravi Kumar, B and Pramanick, A K and Das, Goutam (2006) Development of Quasi-crystal Reinforced Aluminium based Metal matrix Composites. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Srivastava, V C and Ellendt, N and Meyer, C and Uhlenwinkel, V (2014) Bulk synthesis of amorphous and nano-crystalline materials by spray forming. Materialwissenschaft und Werkstofftechnik, 45(8) (IF-0.505). pp. 744-757.

Srivastava, V C and Ghosal, P (2002) Microstructure and phase formation in spray-deposited Al–18%Si–5%Fe–1.5%Cu alloy. Materials Letters, 56 (5). pp. 797-801.

Srivastava, V C and Ghosal, P and Ojha, S N (2002) Microstructure and phase formation in spray-deposited Al-18%Si-5%Fe-1.5%Cu alloy. Materials Letters, 56 (5). pp. 797-801.

Srivastava, V C and Ghosal, P and Ojha, S N (2002) Microstructure and phase formation in spray-deposited Al-18%Si-5%Fe-1.5%Cu alloy. Materials Letters, 56 (5). pp. 797-801.

Srivastava, V C and Mishra, Suman K and Das, Goutam and Ghosh, R N (2006) Study of Structural Evaluation and Mechanical properties of IF Steel and Aluminium sheets processes by ARB process. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Srivastava, V C and Ojha, S N (2005) Microstructure and electrical conductivity of Al-SiCp composites produced by spray forming process. Bulletin of Materials Science, 28 (2). pp. 125-130.

Srivastava, V C and Schneider, A and Uhlenwinkel, V and Bauckhage, K (2004) Effect of porosity and reinforcement content on the electrical conductivity of spray formed 2014-Al alloy + SiCp composites. Journal of Materials Science, 39 (22). pp. 6821-6825.

Srivastava, V C and Surreddi, K B and Scudino, S and Schowalter, M and Schulz, A and Rosenauer, A and Zoch, W and Eckert, J (2009) Spray forming of bulk Al85Y8Ni5Co2 with co-existing amorphous, nano- and micro-crystalline structures. Transactions of the Indian Institute of Metals, 62 (4-5). pp. 331-335.

Starman, S and Matz, V (2011) Automated System for Crack Detection using Infrared Thermographic Testing. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Starman, S and Matz, V (2011) Real Implementation of Ultrasonic Phased Array Technology Using Advanced Signal Processing Algorithms. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Stephen, A and Ananth, M V and Ravichandran, V and Narasimhan, B R V (2000) Magnetic properties of electrodeposited nickel-manganese alloys: Effect of Ni/Mn bath ratio. Journal of Applied Electrochemistry, 30 (11). pp. 1313-1316.

Subrahmanyam, T V and Khangaonkar, P R (1982) Adsorption and desorption studies - chalcopyrite-xanthate system. Anais da academia brasileira de ciencias, 54 (1). p. 265.

Subrahmanyam, T V and Khangaonkar, P R (1983) Xanthate adsorption on chalcopyrite. Anais da academia brasileira de ciencias, 55 (3). pp. 287-291.

Subramanyam, AV and Altekar, V A and Narasimhan, M D (1980) Alkali attack by molten-salts on alumino-silicate samples. Refractories Journal (3). pp. 12-19.

Sundaracharlu, R (1958) A Consumers Appreciation of the Symposium. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Sundaresan, S and Albert, S K and Sireesha, M and Swaminathan, J and Kamaraj, M (2005) Stress rutpure behavior of transition joints between modified Kr-Mo steel and 316 L(N) SS. Transactions Of The Indian Institute Of Metals , 58 (2-3). pp. 493-499.

Supriya, and Prakash, Amit and Metya, Avijit Kumar and Palit Sagar, S (2011) Application of Ultrasonic Waves in Non-Destructive Testing and Evaluation. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Suresh, B and Rao, M Ananda and Bisoyi, Suryanarayan and Umadevi, T and Sah, Rameshwar and Ram, Maruti K (2013) Response of Reverse Flotation on Iron Ore Slimes Varying in Size Distribution and Assay Content. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Suresh, Nikkam (2013) Flowsheet Design and Layout Preparation of Coal Processing Plants. In: proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18,2013, CSIR-NML Jamshedpur.

Suresh, S and Viswanathan, N N (2015) Hydrogen reduction of single pellet nickel oxide under microwave irradiation. Journal of Metallurgy and Materials Science, 57(4) . pp. 257-264.

Suresh, S and Viswanathan, N N (2013) Microwave mineral processing : A challenge in process intensification. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 141-148.

Sutton, C R and Geiger, G F (1958) Heat and Corrosion-Resistant Alloy Castings of the United States of America. In: Symposium on Production, Properties and Applications of Alloy and special Steels, Feb. 1-4, 1956, NML, Jamshedpur.

Suvarna, Kripa M and Udupa, K. Rajendra and Surendranathan, A O (2013) Corrosion studies on 316L fusion zone and base metal in natural sea water by weight loss method. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 219-226.

Swain, S K and Sen, S (2011) Study of microstructure of thick wall ductile iron castings. Journal of Metallurgy and Materials Science, 53 (2). pp. 133-137.

Swaminathan, J and Chattoraj, I and Gunjan, M K and Konar, J and Updhyay, A K (2007) Failure Analysis of air Pre-Heater Tubes. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Swaminathan, J and Das, C R and Baral, Jayashree and Phaniraj, C and Ghosh, R N and Albert, S K and Bhaduri, A K (2014) Creep strength behavior of boron added P91 steel and its weld in the temperature range of 600–650 degree C. In: Energy Materials Conference proceedings 2014, November 4-6, 2014, Xi'an Shaanxi Provice, China.

Swaminathan, J and Guguloth, K and Gunjan, M K and Roy, P K and Ghosh, R N (2008) Failure analysis and remaining life assessment of service exposed primary reformer heater tubes. Engineering Failure Analysis, 15 (4). pp. 311-331.

Swaminathan, J and Krishna, G and Gunjan, M K and Mahato, B and Ravi Kumar, B and Hansda, K L and Sharma, R K and Upadhyay, A K (2007) Failure Analysis of Water wall Tubes of Boiler No.7. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Swaminathan, J and Singh, Raghubir and Das, Swapan K and Das, Goutam (2006) Failure Analysis of Welded Reformer Tubes of a Fertilizer Unit. In: Proceeding of the International Conference & Exhibition on Pressure Vessels and Piping, 7-9, February 2006, Chennai.

Swaminathan, J and Singh, Raghuvir and Gunjan, M K and Mahato, B (2011) Sensitization induced stress corrosion failure of AISI 347 stainless steel fractionator furnace tubes. Engineering Failure Analysis, 18 (8). pp. 2211-2221.

T

Tarafder, Mita and Chattoraj, I and Nasipuri, M and Tarafder, S and Das, S K (2010) Fractal Analysis of Microstructural Images For Evaluation of HSLA Steel. TMS 2010 139th Annual Meeting & Exhibition - Supplemental Proceedings, 2 . pp. 567-276.

Tarafder, Mita and Chattoraj, I and Tarafder, S and Nasipuri, M (2009) Fractal Analysis to Determine Self-Similar Characteristics in the Microstructure of HSLA Steel. Materials and Manufacturing Processes, 24 . pp. 145-149.

Tarafder, Mita and Chattoraj, I and Tarafder, S and Nasipuri, M (2009) Self-similar and self-affine characteristics of microstructural images of HSLA steel. Materials Science and Technology, 25 (4). pp. 542-548.

Tarafder, Mita and Das, Swapan K and Dash, Byomkesh and Tarafder, S and Chattoraj, I (2006) Fractal Characterisation of Ductile Fracture Surface. Exploratory (OLP). CSIR-NML, Jamshedpur. (Submitted)

Tarafder, Mita and Dey, Swati and Dash, Byomkesh and Sivaprasad, S and Tarafder, S (2004) Initiation fracture toughness of HSLA steel through automatic measurement of stretch zone. Materials Science and Technology, 20 (12). pp. 1531-1537.

Tarafder, Mita and Dey, Swati and Sivaprasad, S and Tarafder, S (2006) A Novel Technique for Extracting Stretch Zone Features from Fractographs. In: Fracture of Nano and Engineering Materials and Structures. Proceedings of the 16th European Conference of Fracture, Alexandroupolis, Greece, July 3–7, 2006, B. ( 2T3). Springer, Netherlands, pp. 145-146. ISBN 978-1-4020-4971-2 (Print) 978-1-4020-4972-9 (Online)

Tarafder, Mita and Dey, Swati and Sivaprasad, S and Tarafder, S and Nasipuri, M (2005) Stretch-zone analysis by image processing for the evaluation of initiation fracture toughness of a HSLA steel. Zeitschrift für Metallkunde, 96 (8). pp. 924-932.

Tarafder, Mita and Sinha, Pankhuri and Kundu, Amrita and Strangwood, M and Davis, Claire (2013) Fractal based correlations for Nb microalloyed steel undergoing static recrystallization. Materials Characterization, 85 . pp. 92-99.

Tarafder, S (2001) Fracture Mechanisms and the Quantification of Fracture Resistance. In: Proceedings of Workshop on Recent Trends in Structural Integrity Assessment. NML, Jamshedpur, India, Jamshedpur, pp. 105-129. ISBN 81-87053-62-3

Tarafder, S (1994) Recent Advances in Heat-Treat Technology. In: Workshop on Heat Treatment and Surface Engineering of Iron and Steels (HTIS-94), May 11-13, 1994, NML, Jamshedpur.

Tarafder, S and Ranganath, V R and Sivaprasad, S and Johri, P (2003) Ductile fracture behaviour of primary heat transport piping material of nuclear reactors. Sadhana, 28 (1-2). pp. 167-186.

Tarafder, S and Sivaprasad, S (2009) Component Integrity Evaluation. In: Metallurgy for Engineers, December 14-16, 2009, NML, Jamshedpur.

Tarafder, S and Tarafder, Mita and Ranganath, V R (1994) Compliance crack length relations for the 4-point bend specimen. Engineering Fracture Mechanics, 47 (6). p. 901.

Tarafder, S and Tarafder, Mita and Ranganath, V R (1994) Compliance crack length relations for the four-point bend specimen. Engineering Fracture Mechanics, 47 (6). pp. 901-907.

Tarafder, S and Tarafder, Mita and Ranganath, V R (1996) Fracture mechanics expressions for the standard chord-supported arc bend specimen. Journal of Testing and Evaluation, 24 (2). pp. 73-79.

Teng, Lidong and Eriksson, Jan-Erik and Badrinathan, Raghu and Sjöden, Olof and Lehman, Anders (2013) Impact Of Electromagnetic Stirring (EMS) On The EAF Process. In: Proceeding of the International Conference on Science and Technology Of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Tewari, C R and Prakash, Ved (1969) Phase changes in Mn1.11 Al 0.89 alloy and their effects on magnetic properties. NML Technical Journal, 11 (3). pp. 18-20.

Tewari, C R and Pramanick, P and Rao, Venkatesh and Mohanty, O N (1992) Microstructural and magnetic-properties of fe-mn-al soft magnetic-alloys. Materials Transactions JIM, 33 (11). pp. 1063-1067.

Tewari, C R and Pramanik, S and Rao, Venkatesh and Mohanty, O N (1992) Microstructural and magnetic-properties of Fe-Mn-Al soft magnetic-alloys. Materials Transactions Jim, 33 (11). pp. 1063-1067.

Tewari, J P and Upadhyaya, G S (1977) Sintering behavior of Ni-Cu-Mo low-alloy steels. Transactions of the Indian Institute of metals, 30 (5). pp. 345-347.

Thangaraj, B and Sankara Narayanan, T S N and Kulandaivelu, R and Lee, Min Ho (2015) A Facile Method to Modify the Characteristics and Corrosion Behavior of 304 Stainless Steel by Surface Nanostructuring toward Biomedical Applications. ACS Appl Mater Interfaces, 7(32) (IF-6.723). pp. 17731-17747.

Thilakan, H R and Lahiri, A K and Banerjee, T (1967) Studies on the resistance and alloy steels against oil-ash Corrosion -Part1. NML Technical Journal, 9 (2). pp. 20-25.

Thilakan, H R and Lahiri, A K and Banerjee, T (1969) Studies on the resistance of alloy steels against oil-ash corrosion-Part II. NML Technical Journal, 11 (1). pp. 12-16.

Thriveni, Thenepalli and Ahn, Young Jun and Han, Choon and Nam, Um and Ahn, Ji-Whan (2013) Scalenohedral calcite crystal growth by carbonation process for CO2 sequestration. Journal of Metallurgy and Materials Science, 55(1) (Non-SCI). pp. 49-57.

Tichit, Didier and Das, N N and Coq, Bernard and Durand, Robert (2002) Preparation of Zr-containing layered double hydroxides and characterization of the acido-basic properties of their mixed oxides. Chemistry of Materials, 14 (4). pp. 1530-1538.

Tiwari, Ashutosh and Pramanick, A K (2012) Characterization of Zr-Ti-Nb alloys by AFM. Training Report (TR). CSIR -NML, Jamshedpur. (Unpublished)

Tiwari, S K and Adhikary, Jhuma and Singh, T B and Singh, Raghuvir (2009) Preparation and characterization of sol–gel derived yttria doped zirconia coatings on AISI 316L. Thin Solid Films, 517 (16). pp. 4502-4508.

Tiwari, S K and Choubey, Pankaj K and Mahapatra, S P (2013) Bound rubber properties of chlorobutyl elastomer nanocomposites: effect of carbon nanotube and storage time. Journal of Metallurgy and Materials Science, 55(3) (Non-SCI). pp. 187-193.

Tiwari, S K and Mishra, T (2006) Studies on corrosion, physical and chemical properties of CRS bars for their use in Narmada Project Canal. Sponsored (SSP). CSIR-NML, Jamshedpur. (Submitted)

Tiwari, S K and Mishra, T and Gunjan, M K and Bhattacharyya, A S and Singh, T B and Singh, Raghuvir (2007) Development and characterization of sol–gel silica–alumina composite coatings on AISI 316L for implant applications. Surface and Coatings Technology, 201 (16-17). pp. 7582-7588.

Tiwari, S K and Tripathi, Manju and Singh, Raghuvir (2013) Influence of SiO, Substitution on Corrosion Behavior of Sol-gel TiO,Coating on Mild Steel. IIM Metal News, 16(5) . pp. 1-4.

Tiwari, Y N (2010) Assessment of SRT & Mechanical properties on boiler tubes. Sponsored (SSP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Tiwari, Y N and Guguloth, K (2011) Stress rupture properties on SA 209 grades (T1/T1a) of steel bloom sample. Sponsored (SSP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Tiwari, Y N and Roy, P K (2011) Assessment of mechanical properties of boiler tubes. Sponsored (SSP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Tiwari, Y N and Singh, S R and Parida, N and Roy, P K (2011) Stress rupture properties evaluation of service exposed boiler tubes. Sponsored (SSP). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Tran, N and Mir, Aparna and Mallik, D and Sinha, Arvind and Nayar, S and Webster, Thomas J (2010) Bactericidal effect of iron oxide nanoparticles on Staphylococcus aureus. International Journal of Nanomedicine, 5 . pp. 277-283.

Trehan, Y N (1967) Ageing characteristics of some Al-Zn-Mg alloy. NML Technical Journal, 9 (3). pp. 4-7.

Trehan, Y N (1967) Epitaxial growth of thin oxide and sulphide films on copper. NML Technical Journal, 9 (1). pp. 9-15.

Trehan, Y N (1968) Thermal expansion characteristics of some Fe-Cr-Mn-N alloys. NML Technical Journal, 10 (2). pp. 31-34.

Trentini, B and Allard, M (1959) Steelmaking by Injection of Oxygen and Lime Powder Irsid-O.L.P. Process. NML Technical Journal, 1 (1). pp. 115-120.

Tripathy, T and Bhagat, R P and Singh, R P (2001) The flocculation performance of grafted sodium alginate and other polymeric flocculants in relation to iron ore slime suspension. European Polymer Journal, 37 (1). pp. 125-130.

Tudu, Mohan Kherual and Sivaprasad, S (2012) Fracture and deformation behaviour of materials. Training Report (TR). CSIR New Delhi, Jamshedpur. (Unpublished)

U

Um, Nam Il and Thriveni, Thenepalli and Nam, Seong-Young and Ahn, Ji-Whan (2013) Effect of water content on accelerated carbonation of municipal solid waste incinerator bottom ash for CO2 capture. Journal of Metallurgy and Materials Science, 55(2) (Non-SCI). pp. 113-117.

Upadhyay, C and Verma, H C and Rath, C and Sahu, K K and Anand, S and Das, R P and Mishra, N C (2001) Mössbauer studies of nanosize Mn1−xZnxFe2O4. Journal of Alloys and Compounds, 326(1-2) . pp. 94-97.

Upadhyay, Hemant and Kundu, T K (2013) Drain Rate and Liquid Level Simulation in Blast Furnace Hearth Based on Plant Data. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

V

Vaidyanath, L R (1981) The Indian Institute of Metals. In: The Indian Institute of Metals, February 15, 1981, NML, Jamshedpur.

Vaish, A K and Akerkar, D D (1988) An electrothermal model for the optimum design and smelting operation in reducing type ferro-alloy furnaces. Transactions of the Indian Institute of metals, 41 (3). pp. 247-254.

Vaish, A K and Akerkar, D D (1988) Quick lime process for the production of calcium silicide through electrothermal smelting. Transactions of the Indian Institute of metals, 41 (4). pp. 385-387.

Vaish, A K and Bhatnagar, S K (2015) Steel making in LD converter for the production of billets - A typical case study. Journal of Metallurgy and Materials Science, 57(4) . pp. 225-235.

Vaish, A K and Biswas, P K and Goswami, N G and Sivaramakrishnan, C S and Ramachandrarao, P (2000) Historical perspective of iron in ancient India. Journal of Metallurgy and materials Science, 42 (1). pp. 65-74.

Vaish, A K and Biswas, P K and Humane, M M and Rao, D S and Goswami, N G (2001) Tribal system of iron making in India -R&D for optimum operation. Journal of Metallurgy and materials Science, 43 (3). pp. 213-220.

Vaish, A K and Goswami, N G (2002) Development in the quality and usage of steel for automobile vehicle. Journal of Metallurgy and materials Science., 44 (2). pp. 59-80.

Vaish, A K and Goswami, N G (2002) Environmental degradation in an integrated steel plant: Specific measures for its sustainable growth. Journal of Metallurgy and materials Science., 44 (4). pp. 203-216.

Vaish, A K and Gupta, R C and Mehrotra, S P (2007) Smelting reduction of iron ore - An optimum approach. Journal of Metallurgy and Materials Science, 49 (3). pp. 129-143.

Vaish, A K and Gupta, R C and Mehrotra, S P (2006) Thermodynamic and kinetic aspects of the smelting reduction of multimetallic Indian magnetite ore. Journal of Metallurgy and Materials Science, 48 (1). pp. 1-12.

Vaish, A K and Humane, M M and De, P K and Mahato, B and Ravi Kumar, B (2003) Effect of texture formation on formability of cold rolled and annealed extra deep drawing and inerstitial free steel sheets. Journal of Metallurgy and materials Science, 45 (1). pp. 1-10.

Vaish, A K and Humane, M M and De, P K and Ranganath, V R and Das, Goutam and Das, Swapan K and Kumar, R and Das, Samar (2001) Effect of thermo-mechanical processing on the microstructure and mechanical properties of micro alloyed steels. Journal of Metallurgy and materials Science, 43 (4). pp. 221-238.

Vaish, A K and Humane, M M and De, P K and Ranganath, V R and Minj, R K and Das, Goutam and Das, S K and Kumar, R and Das, Samar and Lakra, B A and Das, Swapan K and Ravi Kumar, B and Das, Samar and Lakra, B A (2001) Development of microalloyed steels and its design aspects Part I : Medium and low carbon micro-alloyed forging steels. Journal of Metallurgy and materials Science., 43 (3). pp. 147-173.

Vaish, A K and Humane, M M and Singh, S D and Goswami, N G (2002) Environmental management for sustainable growth in foundry industries. Journal of Metallurgy and Materials Science, 44 (3). pp. 135-149.

Vaish, A K and Iyer, G V R and De, P K and Lakra, B A and Chakrabarti, A K and Ramachandrarao, P (2000) Electroslag remelting - Its status, mechanism and refining aspects in the production of quality steels. Journal of Metallurgy and materials Science, 42 (1). pp. 11-29.

Vaish, A K and Mehrotra, S P and Gupta, R C (2006) Thermodynamics and reduction kinetics of iron ore in direct reduction processes. Journal of Metallurgy and Materials Science, 48 (2). pp. 59-73.

Vaish, A K and Minj, R K (2002) Significance of burden distribution in the performance of a blast furnace. Journal of Metallurgy and materials Science., 44 (4). pp. 167-183.

Vaish, A K and Minj, R K and Marutiprasad, Y (2003) Modern features for the optimum performance of blast furnace. Journal of Metallurgy and materials Science, 45 (3). pp. 103-125.

Vaish, A K and Nayak, B and Mehrotra, S P and Gupta, R C (2007) The Ni-Cr-Co bearing magnetite ore of Nagaland, India - its mineralogical characteristics. Journal of Metallurgy and Materials Science, 49 (4). pp. 215-220.

Vaish, A K and Singh, S D and Biswas, D K (2001) Cokeless cupola melting - An efficient and cost effective process for foundries. Journal of Metallurgy and materials Science, 44 (4). pp. 239-245.

Vaish, A K and Singh, S D and Biswas, D K (2002) Development of a thermo-chemical model for efficient, eco-friendly and cost effective melting in cokeless cupola. Journal of Metallurgy and materials Science., 44 (1). pp. 15-29.

Vaish, A K and Singh, S D and Humane, M M and Goswami, N G (2006) Woodchar - A sustainable reductant and renewable source of thermal energy for tribal iron making. Journal of Metallurgy and Materials Science, 48 (1). pp. 51-58.

Vaish, A K and Singh, S D and Minj, R K and Humane, M M (2005) Need to exploit Indian ilmenite for commercial production of titanium sponge by carbo-chlorination process. Journal of Metallurgy and Materials Science, 47 (4). pp. 223-227.

Vaish, A K and Singh, S D and Singh, K K and Paul, K K and Mallik, A K and Ramachandrarao, P (1999) Design aspects of DC arc plasma reactors for materials processing. Bulletin of Electrochemistry, 15 (7-8). pp. 323-328.

Varshney, A and Sangal, S and Pramanick, A K and Mondal, K (2020) On the extent of transformation of austenite to bainitic ferrite and carbide during austempering of high Si steel for prolonged duration and its effect on mechanical properties. Materials Science and Engineering A, 793 (IF-4.652). p. 139764.

Vatchagandhy, J S (1958) An Exposition of Alloy Steels for the Engineer. In: Symposium on Production, Properties & Applications of Alloy & Special steels, Feb. 1-4, 1956, NML, Jamshedpur.

Venkata Siva, S B and Ganguly, R I and Srinivasarao, G and Sahoo, K L (2013) Machinability of Aluminum Metal Matrix Composite Reinforced with In-Situ Ceramic Composite Developed from Mines Waste Colliery Shale. Materials and Manufacturing Processes, 28(10) . pp. 1082-1089.

Venkata Siva, S B and Sahoo, K L and Ganguly, R I and Dash, R R (2012) Effect of Hot Working on Structure and Tribological Properties of Aluminium Reinforced with Aluminium Oxide Particulates. Journal of Materials Engineering and Performance, 21 (7). pp. 1226-1231.

Venkata Siva, S B and Sahoo, K L and Ganguly, R I and Dash, R R and Singh, S K and Satpathy, B K and Srinivasarao, G (2013) Preparation of Aluminum Metal Matrix Composite with Novel In situ Ceramic Composite Particulates, Developed from Waste Colliery Shale Material. Metallurgical and Materials Transactions B , 44 (IF-1.212). pp. 800-808.

Venkata Subramanian, G S and Deshmukh, P R (2013) Clean Coke Making Technologies. In: Proceeding of the International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, 2013, CSIR-NML Jamshedpur.

Venkatadri, A S and Ghosh, M and Ramaswamy, V and Tiwary, S K (1991) Pretreatment of hot metal with soda ash and with soda ash sodium-sulfate mixture. Ironmaking & Steelmaking, 18 (6). pp. 411-416.

Venkataraman, N (1997) Iron and Steel Heritage of Mankind. In: Iron and Steel Heritage of India, November 1997, IIM & Tata Steel, Jamshedpur.

Venkataraman, R and Das, Goutam and Venkataraman, B and Narashima, Rao and Krishnamurty, R (2006) Image processing and statistical analysis of microstructures of as plasma sprayed Alumina–13 wt.% Titania coatings. Surface and Coatings Technology, 201 (6). pp. 3691-3700.

Venkataraman, R and Krishnamurty, R (2006) Evaluation of fracture toughness of as plasma sprayed alumina-13 wt.% titania coatings by micro-indentation techniques. Journal of the European Ceramic Society, 26 (15). pp. 3075-3081.

Venkataraman, R and Parmanick, B and Ravi Kumar, B and Pathak, L C and Das, D K and Venkataraman, B (2006) The influence of substrate on partially rapidly solidified Alumina-3 wt % titania nanocrystalline coatings deposited by plasma spray technique. Surface Engineering for Manufacturing Applications , 890 . pp. 69-75.

Venkataraman, R and Ravi Kumar, B and Krishnamurty, R and Das, D K (2006) A study on phase stability observed in as sprayed Alumina-13 wt.% Titania coatings grown by detonation gun and plasma spraying on low alloy steel substrates. Surface and Coatings Technology, 201 (6). pp. 3087-3095.

Venkataraman, R and Singh, S Pabla and Venkataraman, B and Das, D K and Pathak, L C and Ghosh Chowdhury, S and Ghosh, R N and Ravichandra, D and Rao, G V Narasima and Nair, Keasavan and Kathirkar, Rajesh (2008) A scanning electron microscopic study to observe the changes in the growth morphology of the α phased Alumina–13 wt.% titania coatings during plasma spraying. Surface and Coatings Technology, 202 (21). pp. 5074-5083.

Venkatesan, J and Ashok, K and Venkatakrishnan, P G (2013) Quantification of Slag Carry Over & Its Effect on Melting Practice of Medium Carbon Re-Sulphur Steel. In: Proceedings of The International Conference on Science and Technology of Ironmaking and Steelmaking, December 16-18, CSIR-NML, JSR.

Venkateswararao, V (1992) Microstructural features of rapidly solidified 7075 alloy containing 1.0 wt-percent-Mn. Scripta Metallurgica Et Materialia , 26 (5). pp. 819-823.

Venkateswarlu, K and Chakraborty, M and Murty, B S (2004) Influence of thermo-mechanical processing of Al-5Ti-1B master alloy on its grain refining efficiency. Materials Science and Engineering A, 364 (1-2). pp. 75-83.

Venkateswarlu, K and Das, Goutam and Pramanick, A K and Ray, A K and T, Naveen and Xu, Cheng and Langdon, T G (2006) Microstructure, Tensile Strength of Severely deformed Al-2Si Alloy. In: International Conference on Advanced Materials, 2005, Goa, India.

Venkateswarlu, K and Das, Swapan K and Chakraborty, M and Murty, B S (2003) Influence of thermo-mechanical treatment of Al-5Ti master alloy on its grain refining performance on aluminium. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing , 351 (1-2). pp. 237-243.

Venkateswarlu, K and Ghosh, M and Ray, Ajoy K and Xu, Cheng and Langdon, T G (2008) On the feasibility of using a continuous processing technique incorporating a limited strain imposed by ECAP. Materials Science and Engineering: A, 485 (1-2). pp. 476-480.

Venkateswarlu, K and Ghosh Chowdhury, S and Pathak, L C and Ray, Ajoy K (2007) Microstructural examination of service exposed coal mill liner material. Materials Characterization, 58 (10). pp. 1029-1032.

Venkateswarlu, K and Mohapatra, S and Rao, R G and Ray, Ajoy K and Pathak, L C and Mondal, D P (2006) High abrasive wear response of diamond reinforced composite coating: a factorial design approach. Tribology Letters, 24 (1). pp. 7-14.

Venkateswarlu, K and Murty, B S and Chakraborty, M (2001) Effect of hot rolling and heat treatment of Al–5Ti–1B master alloy on the grain refining efficiency of aluminium. Materials Science and Engineering A, 301 (2). pp. 180-186.

Venkateswarlu, K and Pathak, L C and Ray, Ajoy K and Das, Goutam and Verma, P K and Kumar, M and Ghosh, R N (2004) Microstructure, tensile strength and wear behaviour of Al–Sc alloy. Materials Science and Engineering A, 383 (2). pp. 374-380.

Venkateswarlu, K and Rajnikanth, V and Naveen, T and Sinha, D P and Atiquzzaman, and Ray, Ajoy K (2009) Abrasive wear behavior of thermally sprayed diamond reinforced composite coating deposited with both oxy-acetylene and HVOF techniques. Wear, 266 (9-10). pp. 995-1002.

Venkateswarlu, K and Rajnikanth, V and Ray, Ajoy K and Xu, Cheng and Langdon, T G (2010) The characteristics of aluminum–scandium alloys processed by ECAP. Materials Science and Engineering: A, 527 (6). pp. 1448-1452.

Venkateswarlu, K and Rajnikanth, V and Ray, Ajoy K and Xu, Cheng and Langdon, T G (2010) Effect of A Scandium Addition On An Al-2% Si Alloy Processed by ECAP. Reviews on Advanced Materials Science, 25 (2). pp. 99-106.

Venkateswarlu, K and Rajnikanth, V and Sen, Mani Kuntal and Alhajeri, S N and Langdon, T G (2010) Application of High-Pressure Torsion to Al-Si Alloys with and without Scandium Additions. Materials Science Forum, 667-669 . pp. 743-748.

Venkateswarlu, K and Ray, Ajoy K and Chaudhury, S K and Pathak, L C (2002) Development of Aluminium based Metal Matrix Composites. In: Proceedings of the Indo-Malaysian Joint Workshop (WAM - 2002), 12-13 March, 2002, National Metallurgical Laboratory, Jamshedpur.

Venkateswarlu, K and Saurabh, Suman and Rajnikanth, V and Sahu, Ranjan K and Ray, Ajoy K (2010) Synthesis of TiN Reinforced Aluminium Metal Matrix Composites Through Microwave Sintering. Journal of Materials Engineering and Performance, 19 (2). pp. 231-236.

Venkatraman, B (2011) Advanced NDE and QA for Ensuring Quality and Integrity of Critical Components in Nuclear Industry. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Venugopalan, T and Misra, S and Srikanth, S and Tarafder, S (2013) Preface. Transactions of Indian Institute of Metals, 66(5-6) Special Issue: SI (IF-0.215). p. 445.

Verma, A and Roy, A and Anantharaman, T R (1991) Processing and properties of silver-tin oxide-indium oxide electrical contact materials. International journal of powder metallurgy, 27 (1). pp. 51-56.

Verma, A K and Sharma, S and Ghosh, K S (1996) Ceramics for Automobile Industries. NML Technical Journal, 38 (2). pp. 63-72.

Verma, B N and Kumar, Sanjay and Joarder, B (2011) Improvement in New Grades of Work Roll for Hot Strip Mill through NDE. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.

Verma, N P and Sinha, Arvind (2013) Effect of solid to liquid ratio on the physical properties of injectable nanohydroxyapatite. Journal of Materials Science-Materials in Medicine, 24(1) (IF-2.141). pp. 53-59.

Verma, Piyush Chandra and Mishra, Suman K (2020) Synthesis of iron boride powder by carbothermic reduction method. Materials Today: Proceedings, Online (SNIP-0.576).

Vidyadhar, A and Rao, K Hanumantha (2007) Adsorption mechanism of mixed cationic/anionic collectors in feldspar-quartz flotation system. Journal of Colloid and Interface Science, 306 (2). pp. 195-204.

Vijaya Kumar, T V and Prabhakar, S and Bhaskar Raju, G (2002) Adsorption of oleic acid at sillimanite/water interface. Journal of Colloid and Interface Science, 247 (2). pp. 275-281.

Vijayasarathi, P and Prabhu, S P and Rajaram, Gukan (2015) Abrasive wear behavior of Ti-Al-N hard-faced coatings evaluated with ball-cratering test method. Journal of Metallurgy and Materials Science, Vol. 57, No. 1, January-March 2015, pp. 9-18, 57(1) . pp. 9-18.

Vijayasarthi, P and Kavitha, C (2015) An investigation of design and thermal analysis of the different material on disc brake with frictional heat generation. Journal of Metallurgy and Materials Science, 57(4) . pp. 237-242.

Vikash, Avijeet and Metya, Avijit Kumar and Palit Sagar, S (2011) Application of Ultrasonic Technique for Materials property evaluation. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Viswanath, S G and Jachak, Manish M (2013) Preparation of electrolytic cobalt powder by electrodeposition from cobalt sulphate solution in presence of glycerol and sulfuric acid medium and the study of morphology of the powder. Journal of Metallurgy and Materials Science, 55(4) (Non-SCI). pp. 279-291.

Viswanathan, M (1994) Wire Drawing - Influence of Manufacturing Practice on Wire Quality. In: Tailoring of Properties through Mechanical Processing, 23-24, September 1994, NML, Jamshedpur.

Voice, E W (1960) The Uses and Limitations of Pilot Plants in Studying Iron Making Problems. NML Technical Journal, 2 (1). pp. 24-26.

W

Wanderka, N and Radiguet, B and Sahoo, K L and Banhart, J (2007) Crystallization Behavior of Al87Ni5La7Zr1 Metallic Glass. Materials Science Forum, 539-543 . pp. 1917-1920.

Wilde, B E and Chattoraj, I (1992) The effect of shot peening on hydrogen absorption by and hydrogen permeation through AISI 4130 steels. Scripta Metallurgica et Materialia, 26 (4). pp. 627-632.

Wilde, B E and Chattoraj, I (1992) The effect of shot peening on hydrogen absorption by and hydrogen permeation through aisi-4130 steels. Scripta Metallurgica Et Materialia , 26 (4). pp. 627-632.

Y

Young, M J R and Meadows, B J (1974) Application of stress analysis theory to the prediction of tube-drawing schedules. NML Technical Journal, 16 (3-4). pp. 41-45.

Z

Zandrahimi, Morteza and Ebrahimifar, Hadi (2010) A study on the formation of intermetallic compound coatings on Inconel through pack cementation method. Journal of Metallurgy and Materials Science, 52 (4). pp. 331-339.

Zhou, L and Liu, J and Hao, X J and Strangwood, M and Peyton, A J and Balamurugan, S and Morris, P F and Davis, C L (2011) Quantification of the effect of changes in steel microstructural parameters on EM sensor signals. In: Proceedings of the International Conference on Non Destructive Evaluation for Steel and Allied Industries - NDESAI 2011, Dec. 2-3, 2011, SNTI Auditorium Jamshedpur, India.