Items where Author is "Ghosh Chowdhury, S"

Article

Singh, Raghuvir and Ghosh Chowdhury, S and Das, G and Singh, P K and Chattoraj, I (2012) Low Temperature Sensitization on the Orthogonal Surfaces of Prior deferomed AISI 304LN and aged at 673K to 873K (400 A degress C to 600 A degress C. Metallurgical and Materials Transaction A, 43A (3). pp. 986-1003.

Li, X and Jiao, F and Al-Samman, T and Ghosh Chowdhury, S (2012) Influence of second-phase precipitates on the texture evolution of Mg–Al–Zn alloys during hot deformation. Scripta Materialia, 66 (3-4). pp. 159-162.

Singh, Raghuvir and Ghosh Chowdhury, S and Das, Goutam and Singh, P K and Chattoraj, I (2012) Study on sensitization susceptibility and texture of cold rolled AISI 304LN stainless steel. Materials Science Forum, 702-703 . pp. 677-680.

Saray, O and Purcek, G and Mahato, B and Ghosh Chowdhury, S (2012) Texture evolution of IF-steel sheets processed by equal-channel angular sheet extrusion (ECASE). Materials Science Forum . (In Press)

Ghosh Chowdhury, S and Ravi Kumar, B and Das, Swapan K and Singh, Raghuvir (2011) Influence of Processing on Texture, Grain Boundary Structure and Corrosion Behaviour of Austenitic Stainless Steels. Steel Tech, 5 (4). pp. 43-57.

Ghosh Chowdhury, S and Gubicza, Jeno and Mahato, B and Chinh, Nguyen Q and Hegedus, Zoltan and Langdon, T G (2011) Texture evolution during room temperature ageing of silver processed by equal-channel angular pressing. Scripta Materialia, 64 (11). pp. 1007-1010.

Chakraborty, J and Kumar, Kishor and Ranjan, Rajeev and Ghosh Chowdhury, S and Singh, S R (2011) Thickness-dependent fcc–hcp phase transformation in polycrystalline titanium thin films. Acta Materialia, 59 (7). pp. 2615-2623.

Al-Samman, T and Li, X and Ghosh Chowdhury, S (2010) Orientation dependent slip and twinning during compression and tension of strongly textured magnesium AZ31 alloy. Materials Science and Engineering: A, 527 (15). pp. 3450-3463.

Sahu, Puspendu and Curtze, Sven and Das, Arpan and Mahato, B and Kuokkala, Veli Tapani and Ghosh Chowdhury, S (2010) Stability of austenite and quasi-adiabatic heating during high-strain-rate deformation of twinning-induced plasticity steels. Scripta Materialia, 62 (1). pp. 5-8.

Chakraborty, J and Kumar, Kishor and Ranjan, R and Ghosh Chowdhury, S and Singh, S R (2010) Stress, Texture and Phase Transformation in Titanium Thin Films. Texture and Anisotropy of Polycrystals, 160 . pp. 109-116.

Ghosh Chowdhury, S and Pereloma, Elena V and Santos, D B (2009) Corrigendum to “Evolution of texture at the initial stages of continuous annealing of cold rolled dual-phase steel: Effect of heating rate” [Mater. Sci. Eng.: A 480 (2008) 540–548]. Materials Science and Engineering: A , 525 (1-2). 211- .

Roy, Rajat K and Panda, A K and Ghosh Chowdhury, S and Mitra, A and Ghosh, R N (2009) Effect of annealing treatment on soft magnetic properties of Fe–6.5 wt% Si wide ribbons. Journal of Magnetism and Magnetic Materials, 321 (18). pp. 2865-2870.

Aich, S and Das, D and Al-Omari, I A and Alagarsamy, P and Ghosh Chowdhury, S and Chakraborty, M and Shield, J E and Sellmyer, D J (2009) Microstructures and magnetic properties of rapidly solidified Ni54Fe27-2xGa19+2x ferromagnetic Heusler alloys. Journal of Applied Physics, 105 (7). 07A943.

Mandal, D and Ghosh, M and Pal, J and De, P K and Ghosh Chowdhury, S and Das, S K and Das, Goutam and Ghosh, S (2009) Effect of austempering treatment on microstructure and mechanical properties of high-Si steel. Journal of Materials Science, 44 (4). pp. 1069-1075.

Ghosh Chowdhury, S and Sahu, Puspendu and Mahato, B and De, P K (2009) Evolution of Recrystallization Texture in AISI300 Series Austenitic Stainless Steels After Cold Rolling to Large Strain. Microstructure and Texture in Steels, 22 (22). pp. 361-378.

Singh, Raghuvir and Ghosh Chowdhury, S and Chattoraj, I (2008) Modification of Sensitization Resistance of AISI 304L Stainless Steel through Changes in Grain Size and Grain Boundary Character Distributions. Metallurgical and Materials Transactions A, 39 (10). pp. 2504-2512.

Ghosh Chowdhury, S and Mandal, A and Gubicza, Jeno and Krallics, Gyorgy and Fodor, Arpad (2008) Evolution of microstructure and texture in an ultrafine-grained A16082 alloy during severe plastic deformation. equal-channel angular pressing; aluminium alloy 6082; crystallographic texture; dislocation density; grain boundary misorientation distribution , 490 (1-2). pp. 335-342.

Ghosh Chowdhury, S and Mondal, Amit and Gubicza, Jeno and Krallics, Gyorgy and Fodor, Arpad (2008) Evolution of microstructure and texture in an ultrafine-grained Al6082 alloy during severe plastic deformation. Materials Science and Engineering A, 490 (1-2). pp. 335-342.

Venkataraman, R and Singh, S Pabla and Venkataraman, B and Das, D K and Pathak, L C and Ghosh Chowdhury, S and Ghosh, R N and Ravichandra, D and Rao, G V Narasima and Nair, Keasavan and Kathirkar, Rajesh (2008) A scanning electron microscopic study to observe the changes in the growth morphology of the α phased Alumina–13 wt.% titania coatings during plasma spraying. Surface and Coatings Technology, 202 (21). pp. 5074-5083.

Ghosh Chowdhury, S and Singh, Raghuvir (2008) The influence of recrystallized structure and texture on the sensitization behaviour of a stable austenitic stainless steel (AISI 316L). Scripta Materialia, 58 (12). pp. 1102-1105.

Ghosh Chowdhury, S and Pereloma, Elena V and Santos, D B (2008) Evolution of texture at the initial stages of continuous annealing of cold rolled dual-phase steel: Effect of heating rate. Materials Science and Engineering A, 480 (1-2). pp. 540-548.

Palit Sagar, S and Ravi Kumar, B and Ghosh Chowdhury, S and De, P K and Ghosh, R N (2008) Determination of crystallographic texture in cold-rolled copper and stainless steel by spectrum analysis of ultrasonic signal. Scripta Materialia, 58 (7). pp. 595-598.

Hamada, A S and Sahu, Puspendu and Ghosh Chowdhury, S and Karjalainen, L P and Levoska, J and Oittinen, T (2008) Kinetics of the γ → ε Martensitic Transformation in Fine-Grained Fe-26Mn-0.14C Austenitic Steel. Metallurgical and Materials Transactions A, 39 (2). pp. 462-465.

Ghosh Chowdhury, S and Xu, Cheng and Langdon, T G (2008) Texture evolution in an aluminum alloy processed by ECAP with concurrent precipitate fragmentation. Materials Science and Engineering: A, 473 (1-2). pp. 219-225.

Ghosh Chowdhury, S and Xu, Cheng and Langdon, T G (2008) Texture evolution in an aluminum alloy processed by ECAP with concurrent precipitate fragmentation. Materials Science And Engineering A-Structural Materials Properties Microstructure And Processing , 473 (1-2). pp. 219-225.

Ghosh Chowdhury, S and Kumar, P and De, P K (2008) Evolution of grain-boundary character distribution during iterative processing of an austenitic stainless steel. Philosophical Magazine Letters Online ISSN 1362-3036, 88 (6). pp. 407-414.

Ghosh Chowdhury, S and Mahato, B and Da silva, H R and Lourenco, G G and Santos, D B (2008) Evolution of texture in ultra-fine grained ferrite through warm-rolling and intercritical annealing. Nanomaterials By Severe Plastic Deformation Iv, Pts 1 And 2 Book Series: Materials Science Forum , 584-586 (1-2). pp. 610-616.

Singh, Raghuvir and Ghosh Chowdhury, S and Tiwari, S K and Dahotre, B (2008) Laser surface processing of Ti6Al4V in gaseous nitrogen: corrosion performance in physiological solution. Journal of Materials Science: Materials in Medicine, 19 (3). pp. 1363-1369.

Srivastava, V C and Uhlenwinkel, V and Schulz, A and Zoch, H -W and Mukhopadhyay, N K and Ghosh Chowdhury, S (2008) Synthesis of single phase i-AlCuFe bulk quasicrystal by spray forming. Zeitschirft fuer Kristallographie, 223 . pp. 711-715.

Srinivasan, A and Ghosh Chowdhury, S and Srivastava, V C and Swaminathan, J and Poddar, Palash and De, P K (2007) Microstructural and textural evolution during large strain hot rolling (LSR) of Mg–Al (AZ31) alloy. Materials Science and Technology, 23 (11). pp. 1313-1320.

Venkateswarlu, K and Ghosh Chowdhury, S and Pathak, L C and Ray, Ajoy K (2007) Microstructural examination of service exposed coal mill liner material. Materials Characterization, 58 (10). pp. 1029-1032.

Singh, Raghuvir and Ghosh Chowdhury, S and Ravi Kumar, B and Das, Swapan K and De, P K and Chattoraj, I (2007) The importance of grain size relative to grain boundary character on the sensitization of metastable austenitic stainless steel. Scripta Materialia, 57 (3). pp. 185-188.

Basu, A and Majumdar, J Dutta and Ghosh Chowdhury, S and AjiKumar, P K and Tyagi, A K and Baldevraj, and Manna, I (2007) Microstructural and texture studies of gas-nitrided Cr-coated low-alloy high-carbon steel. Surface and Coatings Technology, 201 (16-17). pp. 6985-6992.

Ravi Kumar, B and Ghosh Chowdhury, S and Narasaiah, N and Mahato, B and Das, Swapan K (2007) Role of Grain Boundary Character Distribution on Tensile Properties of 304L Stainless Steel. Metallurgical and Materials Transactions A, 38 (5). pp. 1136-1143.

Sahu, Puspendu and Hamada, A S and Ghosh Chowdhury, S and Karjalainen, L P (2007) Structure and microstructure evolution during martensitic transformation in wrought Fe-26Mn-0.14C austenitic steel: an effect of cooling rate. Journal Of Applied Crystallography, 40 (2). pp. 354-361.

Ghosh Chowdhury, S and Ray, R K and Jena, A K (2007) Deformation-induced structural transformation in boron-doped Ni76Al24. Intermetallics, 15 (3). pp. 260-269.

Ghosh Chowdhury, S and Datta, Sudarsan and Ravi Kumar, B and De, P K and Ghosh, R N (2007) Randomization of texture during recrystallization of austenite in a cold rolled metastable austenitic stainless steel. Materials Science and Engineering A, 443 (1-2). pp. 114-119.

Ghosh Chowdhury, S and Das, Samar and Ravi Kumar, B and De, P K (2006) Twinning-induced sluggish evolution of texture during recrystallization in AISI 316L stainless steel after cold rolling. Metallurgical And Materials Transactions A-Physical Metallurgy And Materials, 37 A (8). pp. 2349-2359.

Ghosh Chowdhury, S and Dutta, Abhijit and Ravi Kumar, B and Kumar, Amit (2006) Textural evolution during accumulative roll bonding of an Al–Li alloy. Materials Science and Engineering A, 428 (1-2). pp. 351-357.

Ghosh Chowdhury, S and Srivastava, V C and Ravi Kumar, B and Soren, S (2006) Evolution of texture during accumulative roll bonding (ARB) and its comparison with normal cold rolled aluminium–manganese alloy. Scripta Materialia, 54 (9). pp. 1691-1696.

Panda, A K and Ghosh Chowdhury, S and Mitra, A and Nishiyama, N (2006) Electron transport behaviour and soft magnetic properties of bulk amorphous Fe72Si4B20Nb4 alloy. Journal of Physics D: Applied Physics, 39 . pp. 3536-3542.

Ghosh Chowdhury, S and Das, Samar and De, P K (2005) Cold rolling behaviour and textural evolution in AISI 316L austenitic stainless steel. Acta Materialia, 53 (14). pp. 3951-3959.

Ghosh Chowdhury, S and Ray, R K (2005) Violation of Schmid's law and tension-compression asymmetry in L1(2) structured alloys: role of ordered structure. Materials Science and Technology, 21 (2). pp. 211-217.

Ghosh Chowdhury, S (2005) Development of texture during cold rolling in AA5182 alloy. Scripta Materialia, 52 (2). pp. 99-105.

Mallikarjun, K and Suwas, S and Ghosh Chowdhury, S and Bhargava, S (2003) Effect of prior beta processing steps on microstructural refinement during thermomechanical processing of a two phase (alpha+beta) titanium alloy. Materials Science and Technology, 19 (12). pp. 1688-1696.

Das, Goutam and Ghosh Chowdhury, S and Sahay, S K and Ranganath, V R and Vaze, K K (2003) Development and validation of ball indentation technique to evaluate the mechanical properties of materials. Transactions Of The Indian Institute Of Metals , 56 (5). pp. 465-475.

Bahadur, Aruna and Ravi Kumar, B and Ghosh Chowdhury, S (2003) Effect of Thermomechanical Treatment on X-Ray Elastic Constants and Residual Stresses in HSLA-100 Steel. Journal of Nondestructive Evaluation, 22 (2). pp. 53-62.

Das, Goutam and Ghosh, Sukomal and Ghosh Chowdhury, S and Ghosh, Sabita and Das, Swapan K and Bhattacharya, D K (2003) Investigation of sub-surface cracks in continuous cast billets. Engineering Failure Analysis, 10 (3). pp. 363-370.

Das, Goutam and Ghosh Chowdhury, S and Ray, Ashok K and Das, Swapan K and Bhattacharya, D K (2003) Turbine blade failure in a thermal power plant. Engineering Failure Analysis, 10 (1). pp. 85-91.

Das, Goutam and Ghosh Chowdhury, S and Ray, Ashok K and Das, Swapan K and Bhattacharya, D K (2002) Failure of a super heater tube. Engineering Failure Analysis, 9 (5). pp. 563-570.

Ray, Ajoy K and Tiwari, Y N and Chaudhuri, S and Ranganath, V R and Sivaprasad, S and Roy, P K and Das, Goutam and Ghosh Chowdhury, S and Kumar, P and Ghosh, R N (2002) Remaining life assessment of service exposed reheater and superheater tubes in a boiler of a thermal power plant. Engineering Failure Analysis , 21 (1-2). pp. 109-121.

Ghosh Chowdhury, S and Das, Swapan K and Ravi Kumar, B and Kumar, S and Gottstein, G (2002) Textural development in AISI 316 stainless steel during cold rolling and annealing. Textures of Materials, 408-4 . pp. 1371-1376.

Ghosh Chowdhury, S and Kumar, Pravesh and Das, Swapan K and Bhattacharya, D K and Parida, N (2001) Failure analysis of high temperature studs. Engineering Failure Analysis, 8 (6). pp. 521-528.

Ravi Kumar, B and Bhattacharya, D K and Das, Swapan K and Ghosh Chowdhury, S (2000) Premature fatigue failure of a spring due to quench cracks. Engineering Failure Analysis, 7 (6). pp. 377-384.

Ghosh Chowdhury, S and Jena, A K and Ray, R K (2000) Recovery and ordering in cold-rolled boron-doped Ni76Al24. Metallurgical and Materials Transactions A, 31 (9). pp. 2127-2134.

Ghosh Chowdhury, S and Ray, R K and Jena, A K (2000) Texture evolution during recrystallization in a boron-doped Ni76Al24 alloy. Materials Science and Engineering A, 277 (1-2). pp. 1-10.

Mukhopadhyay, N K and Ghosh Chowdhury, S and Sinha, R K and Bhattacharya, D K and Chaudhuri, S (1999) Remaining life estimation of a service exposed economiser tube. Engineering Failure Analysis, 6 (4). pp. 233-243.

Ghosh Chowdhury, S and Jena, A K and Ray, R K (1998) Recrystallization behavior of boron-doped Ni76Al24. Metallurgical and Materials Transactions A, 29 (12). pp. 2893-2902.

Ghosh Chowdhury, S and Mukhopadhyay, N K and Das, Goutam and Das, Swapan K and Bhattacharya, D K (1998) Failure analysis of aweld repaired steam turbine casing. Engineering Failure Analysis, 5 (3). pp. 205-218.

Ghosh Chowdhury, S and Mukhopadhyay, N K and Das, Goutam and Das, Swapan K and Bhattacharya, D K (1998) Failure analysis of a weld repaired steam turbine casing. Engineering Failure Analysis, 5 (3). pp. 205-218.

Mukhopadhyay, N K and Ghosh Chowdhury, S and Das, Goutam and Chattoraj, I and Das, S K and Bhattacharya, D K (1998) An investigation of the failure of low pressure steam turbine blades. Engineering Failure Analysis, 5 (3). pp. 181-193.

Ghosh Chowdhury, S and Ray, R K and Jena, A K (1998) Rolling texture in the intermetallic compound Ni76Al24(B). Materials Science and Engineering A, 246 (1-2). pp. 289-301.

Mukhopadhyay, N K and Das, Swapan K and Ravi Kumar, B and Ranganath, V R and Ghosh Chowdhury, S (1997) Premature failure of a leaf spring due to improper materials processing. Engineering Failure Analysis, 4 (3). pp. 161-170.

Conference or Workshop Item

Ghosh Chowdhury, S and Munda, Parikshit and Singh, S R (2010) Development of Advanced High Strength Steels (AHSS) for Automobiles: A Review on Design Criteria. In: International Conference : Automotive Materials & Manufacturing - 2010, Oct 2010, Pune.

Srivastava, V C and Singh, T and Kumar, S and Ghosh Chowdhury, S and Jindal, Vikas (2007) Microstructural Characteristics of Accumulative Roll Bonded Ni-Al Based Metal Intermetallic Laminate Composite. In: International Conference on Recent Advances in Composite Materials, 2007, New Delhi, India, February 20-23, 2007, New Delhi.

Ray, Ashok K and Tiwari, Y N and Sahu, J K and Swaminathan, J and Roy, P K and Sinha, S K and Das, Goutam and Ghosh Chowdhury, S and Kumar, P and Chaudhuri, S (2001) Effect of Oxide Scale Deposition on the Residual Life of Service Exposed Reheater Tubes in Boiler of a Thermal Power Plant. In: National Seminar on Corrosion and Its Prevention(NSCP-2001), 13-14, December, 2001, National Metallurgical Laboratory, Jamshedpur.

Ghosh Chowdhury, S (1999) X-ray diffraction: principles and its application to structural analysis. In: UNSPECIFIED.

Ghosh Chowdhury, S (1997) Failures due to improper hardening of steel components. In: UNSPECIFIED.

Project Reports

Munda, Parikshit and Das, Swapan K and Husain, Md Murtuja and Ghosh Chowdhury, S and Parida, N (2011) Failure Investigation of 1st Stage LPCR Blade Pertaining to Aero-Engine No. 8831010. Other (TMP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Munda, Parikshit and Das, Swapan K and Prakash, Amit and Ghosh Chowdhury, S and Parida, N (2011) Failure Investigation of 1st Stage Rotor Blade Pertaining to Aero-Engine No. HDR-80086U. Other (TMP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Murmu, Laxmi and Ghosh Chowdhury, S and Gunjan, M K (2011) Project report on Microstructural Evolution of Ultra Fine Grained C-Mn Steel warm Rolling and Inter-Critical Annealed. Training Report (TR). CSIR -NML Jamshedpur, Jamshedpur. (Submitted)

Munda , Parikshit and Das, Swapan K and Ghosh Chowdhury, S and Das, Goutam and Singh, S R (2010) Investigation on the Failure of Gear Pump. Sponsored (SSP). National Metallurgical Laboratory, Jamshedpur. (Submitted)

Rajinikanth, V and Munda, Parikshit and Mandal, D and Minj, R K and Das, Swapan K and Ghosh Chowdhury, S and Singh, S R (2009) Development and Evaluation of Wear Resistant Material. Exploratory (OLP). NML, Jamshedpur. (Submitted)